|
Details, datasheet, quote on part number:P1602CA
| |
Datasheet text preview:
Compak Two-chip SIDACtor Device
Compak Two-chip SIDACtor Device
1 (T) 3 (R) 2 (G)
The modified DO-214AA SIDACtor device provides low-cost, longitudinal protection. SIDACtor devices are used to enable equipment to meet various regulatory requirements including GR 1089, ITU K.20, K.21, and K.45, IEC 60950, UL 60950, and TIA-968 (formerly known as FCC Part 68).
Electrical Parameters
Part Number P1402C_ P1602C_ P2202C_ P2702C_ P3002C_ P3602C_ P4202C_ P4802C_ P6002C_ VDRM Volts 58 65 90 120 140 170 190 220 275 VS Volts 77 95 130 160 180 220 250 300 350 VDRM Volts Pins 1-3 116 130 180 240 280 340 380 440 550 154 190 260 320 360 440 500 600 700 VS Volts VT Volts 4 4 4 4 4 4 4 4 4 IDRM µAmps 5 5 5 5 5 5 5 5 5 IS mAmps 800 800 800 800 800 800 800 800 800 IT Amps 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 IH mAmps 120 120 120 120 120 120 120 120 120 CO pF Pins 1-3 15 15 15 15 15 15 15 15 15
Pins1-2, 2-3
* For surge ratings, see table below. General Notes: · All measurements are made at an ambient temperature of 25 °C. IPP applies to -40 °C through +85 °C temperature range. · IPP is a repetitive surge rating and is guaranteed for the life of the product. · Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. · VDRM is measured at IDRM. · VS is measured at 100 V/µs. · Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. · Off-state capacitance is measured between Pins 1-3 at 1 MHz with a 2 V bias. · UL 60950 creepage requirements must be considered.
Surge Ratings
IPP 2x10 µs Amps 150 250 IPP 8x20 µs Amps 150 250 IPP 10x160 µs Amps 90 150 IPP 10x560 µs Amps 50 100 IPP 10x1000 µs Amps 45 80 ITSM 60 Hz Amps 20 30 di/dt Amps/µs 500 500
Series A B*
* Contact factory for release date.
http ://www.teccor.com +1 972-580-7777
2 - 12
© 2003 Teccor Electronics SIDACtor® Data Book and Design Guide
Compak Two-chip SIDACtor Device
Thermal Considerations
Package Modified DO-214AA
Pin 3
Symbol TJ TS RJA
Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient
Value -40 to +150 -65 to +150 85
Unit °C °C °C/W
Pin 1 Pin 2
+I +I
IPP Peak Pulse Current %IPP
tr = rise time to peak value td = decay time to half value
IT IT IS S IH IDRM
V --V VT VT VDRM VDRM VS V
S
100
Peak Value
Wavefor m = tr x td
+V +V
50
Half Value
0 0 tr td t Time (µs)
-I -I
V-I Characteristics tr x td Pulse Wave-form
14
Percent of VS Change %
10
IH (TC = 25 °C)
12 8 6 4 2 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160
2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160
IH
25 °C
25 °C
Ratio of
Case Temperature (TC) °C
Junction Temperature (TJ) °C
Normalized VS Change versus Junction Temperature
Normalized DC Holding Current versus Case Temperature
© 2003 Teccor Electronics SIDACtor® Data Book and Design Guide
2 - 13
http:// www.teccor.com +1 972-580-7777
Data Sheets
|
|
