|
Details, datasheet, quote on part number:P2356UB
| |
Datasheet text preview:
Multiport Balanced SIDACtor Device
Multipor t Balanced SIDACtor Device
1 2 3 6 5 4
This multiport balanced protector is a surface mount alternative to the modified TO-220 package. It is based on a six-pin surface mount SOIC package and uses Teccor's patented "Y" (US Patent 4,905,119) configuration. It is available in surge current ratings up to 500 A. SIDACtor devices are used to enable equipment to meet various regulatory requirements including GR 1089, ITU K.20, K.21, and K.45, IEC 60950, UL 60950, and TIA-968 (formerly known as FCC Part 68).
Electrical Parameters -- Symmetrical
Part Num b er * P1556U_ P1806U_ P2106U_ P2356U_ P2706U_ P3206U_ P3406U_ P5106U_ VDRM Volts 130 150 170 200 230 270 300 420 VS Volts 180 210 250 270 300 350 400 600 VDRM Volt 130 150 170 200 230 270 300 420 VS Volts 180 210 250 270 300 350 400 600 VT Volts 8 8 8 8 8 8 8 8 IDRM µAmps 5 5 5 5 5 5 5 5 IS mAmps 800 800 800 800 800 800 800 800 IT Amps 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 IH mAmps 150 150 150 150 150 150 150 150 CO pF Pins 3-2, 6-5, 1-2, 4-5 40 40 40 40 30 30 30 30
Pins 1-2, 2-3, 1-3
Pins 4-5, 5-6, 4-6
Electrical Parameters -- Asymmetrical
VDRM Volts Part Num b er * A2106U_6 A5030U_6 VS Volts VDRM Volt VS Volts VT Volts 3.5 3.5 IDRM µAmps 5 5 IS mAmps 800 800 IT Amps 2.2 2.2 IH mAmps 120 150 CO pF 40 30
Pins 1-2, 2-3, 4-5, 5-6 170 400 250 550
Pins 4-6, 1-3 50 270 80 340
* For individual "UA", "UB", and "UC" surge ratings, see table below. General Notes: · All measurements are made at an ambient temperature of 25 °C. IPP applies to -40 °C through +85 °C temperature range. · IPP is a repetitive surge rating and is guaranteed for the life of the product. · Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. · VDRM is measured at IDRM. · VS is measured at 100 V/µs. · Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. · Off-state capacitance is measured between Pins 1-2 and 3-2 at 1 MHz with a 2 V bias and is a typical value for "UA" product. "UB" and "UC" capacitance is approximately 10 pF higher. · Device is designed to meet balance requirements of GTS 8700 and GR 974.
Surge Ratings
IPP 2x10 µs Amps 150 250 500 IPP 8x20 µs Amps 150 250 400 IPP 10x160 µs Amps 90 150 200 IPP 10x560 µs Amps 50 100 150 IPP 10x1000 µs Amps 45 80 100 ITSM 60 Hz Amps 20 30 50 di/dt Amps/µs 500 500 500
Series A B C
http ://www.teccor.com +1 972-580-7777
2 - 26
© 2003 Teccor Electronics SIDACtor® Data Book and Design Guide
Multiport Balanced SIDACtor Device
Thermal Considerations
Package Modified MS-013
6 5 4 1 2
Symbol TJ TS RJA
Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient
Value -40 to +125 -65 to +150 60
Unit °C °C °C/W
+I +I
IPP Peak Pulse Current %IPP
tr = rise time to peak value td = decay time to half value
IT IT IS S IH IDRM
V --V VT VT VDRM VDRM VS V
S
100
Peak Value
Wavefor m = tr x td
+V +V
50
Half Value
0 0 tr td t Time (µs)
-I -I
V-I Characteristics tr x td Pulse Wave-form
14
Percent of VS Change %
10
IH (TC = 25 °C)
12 8 6 4 2 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160
2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160
IH
25 °C
25 °C
Ratio of
Case Temperature (TC) °C
Junction Temperature (TJ) °C
Normalized VS Change versus Junction Temperature
Normalized DC Holding Current versus Case Temperature
© 2003 Teccor Electronics SIDACtor® Data Book and Design Guide
2 - 27
http:// www.teccor.com +1 972-580-7777
Data Sheets
3
|
|
