Digchip : Database on electronics components
Electronics components database



Details, datasheet, quote on part number: S6070W
 
 
Part numberS6070W
CategoryDiscrete
DescriptionTeccor® SCR ;; Package= TO-252AA SM D-pak
CompanyTeccor Electronics
DatasheetDownload S6070W datasheet
Request For QuoteFind where to buy S6070W
 


 
Specifications, Features, Applications

The Teccor line of thyristor SCR semi-conductors are half-wave, unidirectional, gate-controlled rectifiers which complement Teccor's line of sensitive SCRs. Teccor offers devices with ratings 70 A and 1000 V, with gate sensitivities from to 50 mA. If gate currents in the 500 A ranges are required, see "Sensitive SCRs" section of this catalog. Three packages are offered in electrically isolated construction where the case or tab is internally isolated to allow the use of low-cost assembly and convenient packaging techniques. The Teccor line of SCRs features glass-passivated junctions to ensure long-term reliability and parameter stability. Teccor's glass offers a rugged, reliable barrier against junction contamination. Variations of devices covered in this data sheet are available for custom design applications. Consult the factory for more information.

Features

Electrically-isolated package High voltage capability 1000 V High surge capability 950 A Glass-passivated chip

Surface mount package 1 A series New small profile three-leaded Compak package Packaged in embossed carrier tape with 2,500 devices per reel Can replace SOT-223


di/dt Maximum rate-of-rise of on-state current; IGT 150 mA with 0.1 s rise time dv/dt Critical rate of applied forward voltage I2t RMS surge (non-repetitive) on-state current for period 8.3 ms for fusing IDRM and IRRM Peak off-state forward and reverse current at VDRM and VRRM Igt dc gate trigger current; 12 V dc; 60 W for 16 A devices and 30 W for 70 A devices IGM Peak gate current IH dc holding current; gate open IT Maximum on-state current ITSM Peak one-cycle forward surge current PG(AV) Average gate power dissipation PGM Peak gate power dissipation tgt Gate controlled turn-on time; gate pulse = 100 mA; minimum width 15 s with rise time s tq Circuit commutated turn-off time

VDRM and VRRM Repetitive peak off-state forward and reverse voltage Vgt DC gate trigger voltage; 12 V dc; 60 W for 16 A devices and 30 W for 70 A devices VTM Peak on-state voltage at maximum rated RMS current

All measurements are made 60 Hz with a resistive load at an ambient temperature +25 C unless otherwise specified. Operating temperature range (TJ) +125 C for TO-92 devices and +125 C for all other packages. Storage temperature range (TS) +150 C for TO-92 devices, +150 C for TO-202 and TO-220 devices, and +125 C for all others. Lead solder temperature is a maximum 230 C for 10 seconds maximum; 1/16" (1.59 mm) from case. The case temperature (TC) is measured as shown on dimensional outline drawings in the "Package Dimensions" sectionof this catalog.

See Figure E6.5 through Figure E6.16 for current rating at specified operating case temperature. See Figure E6.1 and Figure E6.2 for free air current rating. See Figure E6.19 and Figure E6.20 for instantaneous on-state current versus on-state voltage (typical). See Figure E6.18 for IGT versus TC. See Figure E6.17 for IH versus TC. For more than one full cycle rating, see Figure E6.23. See Figure E6.22 for tgt versus IGT. See Figure E6.21 for VGT versus TC. Test conditions are as follows: 1 A for 1 A devices and 2 A for all other devices Pulse duration = 50 s, dv/dt = 20 V/s, di/dt = -10 A/s for 1 A devices, and -30 A/s for other devices IGT mA at turn-on (10) See Figure E6.5 through Figure E6.10 for maximum allowable case temperatures at maximum rated current.

(11) See package outlines for lead form configuration. When ordering special lead forming, add type number as suffix to part number. (12) Pulse width s (13) Initial on-state current mA dc for 1 A through 16 A devices; mA dc for 20 A through 70 A devices. = TJ for test conditions in off state. (15) The or M package rating is intended for high surge condition use only and not recommended for 50 A rms continuous current use since narrow pin lead temperature can exceed PCB solder melting temperature. Teccor's J package or W package is recommended for 50 A rms continuous current requirements. (16) For various durations of an exponentially decaying current waveform, see Figure E6.3 and Figure E6.4. (tW is defined as 5 time constants.) (17) Minimum non-trigger VGT 0.2 V.




Related products with the same datasheet
S2006F1   S2006L   S2006V   S2008D   S2008F1   S2008L  
S2008R   S2008V   S2010D   S2010F1   S2010L   S2010R  


Some Part number from the same manufacture Teccor Electronics
S6N1 Teccor® SCR ;; Package= TO-252AA SM D-pak
S6S Teccor® Sensitive SCR ;; Package= TO-92 Three-lead
S8006D Teccor® SCR ;; Package= TO-252AA SM D-pak
SLP1101U Multi-port Line Protector
ST-32 Teccor® Diac ;; Package= DO-35
ST-36 Bilateral Trigger Diacs et And ST Series
ST-36A Teccor® Diac ;; Package= DO-35
SXX06 SCRS (1 - 70 Amps)
SXX08
SXX1E
T106B1 Teccor® Sensitive SCR ;; Package= TO-92 Three-lead
TCR22 Sensitive SCRS (0.8 - 10 Amps)
TCR22-4 Teccor® Sensitive SCR ;; Package= TO-92 Three-lead
P3203A Solid State Crowbar Devices
S4001L SCRs 1-70 AMPS Non-sensitive GATE
S6050J
P3403Z Solid State Crowbar Devices
P3100Z
AC10DGM Thyristor Product Catalog
P1800S Sidactor Device
AC16BGM Thyristor Product Catalog