|Category||Power Management => Battery Management|
|Description||Micromaster - System Supervisor With Power Supply Monitor, Watchdog And Battery Backup|
|Datasheet||Download TC71 datasheet
|TC70/71 MICROMASTERTM SYSTEM SUPERVISOR WITH POWER SUPPLY MONITOR, WATCHDOG AND BATTERY BACKUP
s Maximum Functional Integration: Precision Power Supply Monitor, Watchdog Timer, External RESET Override, Threshold Detector and Battery Backup Controller an 8-Pin Package Generates Power-on RESET and Guards Against Unstable Processor Operation Resulting from Power "Brown-out" Automatically Halts and Restarts an Out-ofControl Microprocessor Output Can be Wire-ORed, or Hooked to Manual RESET Pushbutton Switch Watchdog Disable Pin for Easier Prototyping (TC70) Voltage Monitor for Power Fail or Low Battery Warning (TC71) Available in 8-Pin Plastic DIP or 8-Pin SOIC Packages Cost Effective
The is a fully-integrated power supply monitor, watchdog and battery backup circuit in a space-saving 8-pin package. When power is initially applied, the TC70/71 holds the processor in its reset state for a minimum of 500msec after VCC is in tolerance to ensure stable system start-up. After start-up, processor sanity is monitored by the on-board watchdog circuit. The processor must provide periodic highto-low level transitions to the TC70/71 to verify proper execution. Should the processor fail to supply this signal within the specified timeout period, an out-of-control processor is indicated and the TC70/71 issues a momentary processor reset as a result. The TC70 also features a watchdog disable pin to facilitate system test and debug. The output of the TC70/71 can be wire-ORed to a pushbutton switch (or electronic signal) to reset the processor. When connected to a push-button switch, the TC70/71 provides contact debounce. The integrated battery backup circuit on-board the TC70/ 71 converts CMOS RAM into nonvolatile memory by first write-protecting, then switching the VCC line of the RAM over to an external battery. The TC71 incorporates an additional 1.3V threshold detector for power fail warning, low battery detection or to monitor power supply voltages other than +5V.TYPICAL APPLICATIONS
All Microprocessor-based Systems Test Equipment Instrumentation Set-Top Boxes
8-Pin SOIC 8-Pin Plastic DIP 8-Pin SOIC 8-Pin Plastic DIP 8-Pin SOIC 8-Pin Plastic DIP 8-Pin SOIC 8-Pin Plastic DIPMICROMASTERTM SYSTEM SUPERVISOR WITH POWER SUPPLY MONITOR, WATCHDOG AND BATTERY BACKUP
Voltage (Any Pin) with Respect to Ground................................ GND 0.3 to VCC + 0.3V Operating Temperature Range............... to +85°C Storage Temperature Range................ to +150°C Lead Temperature (Soldering, 10 sec)................. +300°C
*This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to Absolute Maximum Rating Conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS: Recommended DC Operations: TA = TMIN to TMAX, unless otherwise specified.Supply Voltage Input HIGH Level Input HIGH Level Input LOW Level
Note 1 CEI, WDD (Note 1) RS (Note 1) CEI, WDD, RS (Note 1)
ELECTRICAL CHARACTERISTICS: DC: TA = TMIN to TMAX, VCC to 5.5V, unless otherwise specified.
Operating Current Operating Current in Battery Backup Mode Input Leakage Input Leakage Input Leakage Battery Standby Current Battery Standby Current
ELECTRICAL CHARACTERISTICS: DC: Power Supply Monitor, EXT. RESET and Watchdog: TA = TMIN to TMAX, VCC to 5.5V, unless otherwise specified.
Output Current 0.4V (RS, TDO, CEO, PF Pins) Output Current 2.4V (TDO, CEO, PF Pins) WDD Input Current RS Strobe (HIGH) Level RS Strobe (LOW) Level VCC Trip Point
ELECTRICAL CHARACTERISTICS: DC: Battery Backup and Threshold Detector: TA = TMIN to TMAX, VCC to 5.5V, unless otherwise specified.VCCO Output Voltage VOUT in Battery Backup Mode
ELECTRICAL CHARACTERISTICS: (Cont.) DC: Battery Backup and Threshold Detector: TA = TMIN to TMAX, VCC to 5.5V, unless otherwise specified.IOUT1 IOUT2 VSW VHYST VOHCEO VTDI ITDI VTDI (HYST)
VCCO Output Current VCCO Output Current in Battery Backup Mode Battery Switchover Threshold (VCC Falling) Battery Switchover Hysteresis CEO Output Voltage in Battery Backup Mode Threshold Detector Trip Voltage Threshold Detector Input Current Threshold Detector Hysteresis
ELECTRICAL CHARACTERISTICS: AC: Power Supply Monitor, EXT. RESET and Watchdog: TA = TMIN to TMAX, VCC to 5.5V, unless otherwisePB Hold Time Reset Active Time RS STROBE Pulsewidth Watchdog Timeout Period VCC Detect to RS LOW
Figure 4 (Note 4) Figure 6 Figure 3 Figure 3 Figure 6
ELECTRICAL CHARACTERISTICS: AC: Battery Backup and Threshold Detector: TA = TMIN to TMAX, VCC to 5.5V, unless otherwise specified.VCC Fall Time From to 3.0V VCC Rise Time From to 4.25V
All voltages referenced to ground. No output load. Measured with VCCO and CEO open. The RS output must be held low for a minimum 20msec to guarantee a reset.
|Related products with the same datasheet|
|Some Part number from the same manufacture TelCom Semiconductor|
|TC7106ACPL 3-1/2 Digit A/D Converter. Drive LCD Display Directly. Internal Reference With Low Temperature Drift 20ppm/degC,typ.|
|TC7107ACPL Micromaster - System Supervisor With Power Supply Monitor, Watchdog And Battery Backup|
|TC7107ARCKW 3-1/2 Digit A/D Converter. Drive Led Display Directly. Internal Reference With Low Temperature Drift 20ppm/degC,typ.|
TC4420COA : 6A High-speed MOSFET Driver. Logic Noninverting.
TC500ACOE : Precision Analog Front End.
TC54VC2901EMB : Voltage Detector. Detected Voltage 2.9V. Output Form: CMOS Output. Tolerance +-1.0%.
TC54VN5502ECB : Voltage Detector. Detected Voltage 5.5V. Output Form: NCH Open Drain. Tolerance +-2.0%.
TC7107RCLW : 3-1/2 Digit A/D Converter. Drive Led Display Directly. Internal Reference With Low Temperature Drift 80ppm/degC,typ.
TCM809TENB : Microp Reset Monitor. Reset VCC Threshold 3.08V. Precision VCC Monitor For 3.0V, 3.3V, 5.0V Nominal System V Supplies.
TC828A : Switched Capacitor Voltage Converter
TC54VC3001ECBSTP : Voltage Detector
TC4949 : Multifunction Very Low Dropout Voltage Regulator
TC54VN4302ECBRTP : Voltage Detector
TC54VN3901EZBSTP : Voltage Detector
TC54VN2502ECBSTP : Voltage Detector
5962-89905012A : Current Mode. ti UC1823, High Speed PWM Controller. Compatible with Voltage or Current-Mode Topologies Practical Operation @ Switching Frequencies 1.0MHz 50ns Propagation Delay to Output High Current Totem Pole Output (1.5A peak) Wide Bandwidth Error Amplifier Fully Latched Logic with Double Pulse Suppression Pulse-by-Pulse Current Limiting Soft Start/Max. Duty Cycle Control Under-Voltage Lockout with.
AD402M81RBA-5 : Low Voltage Operation is More Suitable to be Used on Battery Backup, Portable Electronic.
ADM663A : Fixed. Tri-Mode: +3.3 V, +5 V, Adjustable Micropower Linear Voltage Regulators.
FK1301-7R : 150 Watt DC-DC Converters. Input voltage ranges from 1or 2 outputs kV AC I/O electric strength test voltage Rugged electrical and mechanical design Fully isolated outputs Operating ambient temperature range 4071 °C with convection cooling Output 1 Uo nom Io nom [V DC] [A] Output 1 Uo nom Io nom [V DC] [A] Output 2 Uo nom Io nom [V DC] [A] Output 2 Uo nom Io nom [V DC] [A] Type.
IP7800ASeries : 1 Amp Positive Voltage Regulator. OUTPUT CURRENT TO 1.0A OUTPUT VOLTAGES / V LINE REGULATION / A LOAD REGULATION THERMAL OVERLOAD PROTECTION OUTPUT TRANSISTOR SOA PROTECTION 1% VOLTAGE TOLERANCE (A VERSIONS) The / IP7800 series of 3 terminal regulators is available with several fixed output voltage making them useful in a wide range of applications. The A suffix devices are fully specified.
IRFK2FE50 : ISOlated Base Power Hex Pak(tm) Assembly- Half Bridge Configuration.
LM2320-7 : 50 Watt Ac-dc Converters. Input voltage range or 3 isolated outputs kV AC I/O electric strength test voltage Rugged electrical and mechanical design Outputs individually controlled with excellent dynamic properties Operating ambient temperature range 4071°C with convection cooling Options Input voltage Input frequency Inrush current limitation continuous range by thermistor.
LM2586 : LM2586 - Simple Switcher 3-Amp Flyback Regulator, Package: to 263, Pin Nb=7.
MAX8709 : High-efficiency CCFL Backlight Controller With Smbus Interface The MAX8709 Integrated Backlight Controller is Optimized to Drive Cold-cathode Fluorescent Lamps (CCFLs) Using a Resonant Full-bridge Inverter Architecture. The Resonant Operation Maximizes Striking Capability And Provides Near-sinusoidal Waveforms Over The Entire Input Range to Improve.
PT4105A : Plug-in Power Solutions->Isolated->Single Output. ti PT4105, 12Vout 15W 24V Input ISOlated DC/DC Converter.
UC2544DW : ti UC2544, Power Supply Supervisory Circuit. Includes Over-voltage, Under-voltage, And Current Sensing Circuits Internal 1% Accurate Reference Programmable Time Delays SCR "Crowbar" Drive Of 300mA Remote Activation Capability Optional Over-voltage Latch Uncommitted Comparator Inputs For Low Voltage Sensing (UC1544 Series Only) The monolithic integrated circuits contain all the functions necessary.
UCC284-12 : Low Dropout 0.5a Negative Linear Regulator. Regulation 0.2 V Dropout 0.5 A Wide Input Voltage Range 15 V Low Quiescent Current Irrespective of Load Simple Logic Shutdown Interfacing 12 V, and Adjustable Output 2.5% Duty Cycle Short Circuit Protection The UCC384-x family of negative linear-series pass regulators is tailored for low-dropout applications where low-quiescent power is important.
UWR-3.3/1800Series : 6-10w, DC/DC Converter. Low Cost! Highly reliable! Proven SMT-on-pcb construction Designed to meet UL1950 and EN60950 Qual tested; HALT tested; EMC tested Small packages, x 0.375" Standard pinouts or 15 Volt outputs Choice of 3 wide-range inputs: 4.7-7.25 Volts 9-18 Volts 18-75 Volts Fully isolated, 1500Vdc guaranteed to +100°C operation 5-side metal shielded cases with non-conductive.
TK684xxAB1 : s The TK684xxAB1 is a CMOS LDO regulator. The package is the very small 4-bump flip chip. The IC is designed for portable applications with space requirements. The IC can supply 200mA output current. The IC does not require input capacitor, output capacitor, and noise-bypass capacitor. The IC offers low quiescent current. The output voltage is internally.
SSM3J117TU : The ever-increasing functionality of portable devices like cell phone, DSC and portable audio device is increasing their battery loading. In order to realize longer set operation, we are trying to decrease the system power consumption by lowering the internal operating voltage. Especially, lowering the voltage of the power supply and decreasing the internal.
TLC5946 : 16-Channel, 12-bit PWM LED Driver With 6-Bit Dot Correction The TLC5946 is a 16-channel, constant current sink LED driver. Each channel is individually adjustable with 4096 pulse-width modulated (PWM) steps and 64 constant current sink steps for dot correction. The dot correction adjusts the brightness variations between LEDs. Both grayscale control.
ADP1752 : 800mA Low-Vin LDO Regulator The ADP1752/ADP1753 are CMOS, low dropout linear regulators that operate from 1.6 V to 3.6 V and provide up to 800mA of output current. These Low Vin / Vout LDOs are ideal for regulation of nanometer FPGA geometries operating from 2.5V down to 1.8V I/O rails, and powering core voltages down to 0.75V. Using an advanced proprietary.
PRTR5V0U2D : Ultra Low Capacitance Double Rail-to-rail ESD Protection Ultra low capacitance double rail-to-rail ElectroStatic Discharge (ESD) protection device in a SOT457 (SC-74) small Surface-Mounted Device (SMD) plastic package. The device is designed to protect two Hi-Speed data lines or high-frequency signal lines from the damage caused by ESD and other transients.
PT7M7823XDE : µ µ µ µ µP Supervisor Circuits The PT7M7xxx family microprocessor (µP) supervisory circuits are targeted to improve reliability and accuracy of power-supply circuitry in µP systems. These devices reduce the complexity and number of components required to monitor power-supply and battery functions..
BQ34Z100 : 1s To 16s Impedance Track Fuel Gauge The Texas Instruments bq34z100 is a fuel gauge solution that works independently of battery series-cell configurations, and supports a wide range of Li-Ion and LiFePO4 battery chemistries. Batteries from 3 V to 65 V can be supported through an external voltage translation circuit that can be controlled automatically.