|
|
Part: 5962-8874401FA
Category:
Interface and Interconnect
-> Line Drivers/Interfaces
-> Non-Standard Line Circuits
Description: ti SN55113, Dual Differential Line Driver
Company: Texas Instruments, Inc.
Datasheet: Download 5962-8874401FA datasheet File size : 117 kB
Request For quote: Find where to buy 5962-8874401FA
Datasheet text preview:
SN55113, SN75113 DUAL DIFFERENTIAL LINE DRIVERS
SLLS070C SEPTEMBER 1973 REVISED MARCH 1997
D D D D D D D D D D D D
Choice of Open-Collector, Open-Emitter, or 3-State Outputs High-Impedance Output State for Party-Line Applications Single-Ended or Differential AND/NAND Outputs Single 5-V Supply Dual Channel Operation Compatible With TTL Short-Circuit Protection High-Current Outputs Common and Individual Output Controls Clamp Diodes at Inputs and Outputs Easily Adaptable to SN55114 and SN75114 Applications Designed for Use With SN55115 and SN75115
SN55113 . . . J OR W PACKAGE SN75113 . . . N PACKAGE (TOP VIEW)
1ZP 1ZS 1YS 1YP 1A 1B 1C GND
1 2 3 4 5 6 7 8
16 15 14 13 12 11 10 9
V CC 2ZP 2ZS 2YS 2YP 2A 2C CC
SN55113 . . . FK PACKAGE (TOP VIEW)
description
The SN55113 and SN75113 dual differential line 14 8 drivers with 3-state outputs are designed to 9 10 11 12 13 provide all the features of the SN55114 and SN75114 line drivers with the added feature of driver output controls. Individual controls are provided for each output pair, as well as a NC No internal connection common control for both output pairs. If any output is low, the associated output is in a high-impedance state and the output can neither drive nor load the bus. This permits many devices to be connected together on the same transmission line for party-line applications. The output stages are similar to TTL totem-pole outputs, but with the sink outputs, YS and ZS, and the corresponding active pullup terminals, YP and ZP, available on adjacent package pins. The SN55113 is characterized for operation over the full military temperature range of 55°C to 125°C. The SN75113 is characterized for operation over the temperature range of 0°C to 70°C.
1C GND NC CC 2C
1YS 1YP NC 1A 1B
4 5 6 7
3 2 1 20 19 18 17 16 15
1ZS 1ZP NC VCC 2ZP 2ZS 2YS NC 2YP 2A
Copyright © 1997, Texas Instruments Incorporated
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.
POST OFFICE BOX 655303
· DALLAS, TEXAS 75265
1
SN55113, SN75113 DUAL DIFFERENTIAL LINE DRIVERS
SLLS070C SEPTEMBER 1973 REVISED MARCH 1997
FUNCTION TABLE INPUTS OUTPUT C L X H H H CONTROL CC X L H H H DATA A X X L X H B X X X L H OUTPUTS AND Y Z Z L L H NAND Z Z Z H H L
H = high level, L = low level, X = irrelevant, Z = high impedance (off) B input and 4th line of function table are applicable only to driver number 1.
logic symbol
1C CC 2C 7 9 10 & & EN1
logic diagram (positive logic)
1C 7 4 3
CC EN2 4 3 1 2 12 13 15 14 2C 1YP 1YS 1ZP 1ZS 2YP 2YS 2ZP 2ZS 2A 1A 1B
9
1YP 1YS
10
1 2
1A
5
&
1 1
1ZP 1ZS
5 6
1B
6
1 1 2
12 13
2YP 2YS
11 15 14 2ZP 2ZS
2A
11
2 2 2
This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. Pin numbers shown are for the J, N, and W packages.
2
POST OFFICE BOX 655303
· DALLAS, TEXAS 75265
SN55113, SN75113 DUAL DIFFERENTIAL LINE DRIVERS
SLLS070C SEPTEMBER 1973 REVISED MARCH 1997
schematic
Input 1B Input 1A 5 6 16 V CC 1 k V V 600 9 AND 4 Pullup 1YP 4 k 900 AND Sink 3 Output 1YS 100 5 k 90 333 900 90 5 k 100 600 4 k 9 1 NAND Pullup 1ZP 4 k 600 To Other Driver 1 k
NAND 2 Sink Output 1ZS
500
100
100
500
V
4 k
1.6 k
Output 7 Control 1C
Common Output 9 Control CC 10 Output Control 2C 11 Input 2A
12 13 15 14
AND Pullup 2YP AND Output 2YS NAND Pullup 2ZP NAND Output 2ZS
1 k 8 GND
V ... VCC bus
These components are common to both drivers. Resistor values shown are nominal and in ohms.
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V Off-state voltage applied to open-collector outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 V Continuous total power dissipation (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating free-air temperature range, TA: SN55113 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55°C to 125°C SN75113 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65°C to 150°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: N package . . . . . . . . . . . . . . . . . . . . . 260°C Case temperature for 60 seconds: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: J or W package . . . . . . . . . . . . . . . . 300°C
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. DISSIPATION RATING TABLE PACKAGE FK J N W TA 25°C POWER RATING 1375 mW 1375 mW 1150 mW 1000 mW DERATING FACTOR ABOVE TA = 25°C 11.0 mW/°C 11.0 mW/°C 9.2 mW/°C 8.0 mW/°C TA = 70°C POWER RATING 880 mW 880 mW 736 mW 640 mW TA = 125°C POWER RATING 275 mW 275 mW N/A 200 mW
POST OFFICE BOX 655303
· DALLAS, TEXAS 75265
3
SN55113, SN75113 DUAL DIFFERENTIAL LINE DRIVERS
SLLS070C SEPTEMBER 1973 REVISED MARCH 1997
recommended operating conditions
SN55113 MIN Supply voltage, VCC High-level input voltage, VIH Low-level input voltage, VIL High-level output current, IOH Low-level output current, IOL Operating free-air temperature, TA 55 4.5 2 0.8 40 40 125 0 NOM 5 MAX 5.5 MIN 4.75 2 0.8 40 40 70 SN75113 NOM 5 MAX 5.25 UNIT V V V mA mA °C
electrical characteristics over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER VIK VOH VOL VOK Input clamp voltage High-level output voltage Low-level output voltage Output clamp voltage VCC = MIN, VCC = MIN, , VIL = 0.8 V VCC = MIN, , IOL = 40 mA VCC = MAX, TEST CONDITIONS CONDITIONS II = 12 mA VIH = 2 V, , VIH = 2 V, , IO = 40 mA VOH = 12 V 12 VCC = MAX MAX VOH = 5.25 V 5 25 TA = 25°C, IOZ Off-state (high-impedance-state) output current VCC = MAX, Output controls at at 0.8 V TA = 25°C TA = 125°C TA = 25°C TA = 70°C VO = 0 to VCC VO = 0 VO = 0.4 V VO = 2.4 V VO = VCC II Input current at maximum maximum input voltage High-level input current Low-level input current Short-circuit output current§ Supply current (both drivers) A, B, C CC A, B, C CC A, B, C CC VCC = MAX MAX, VI = 5 5 V 5.5 ± 10 150 ± 80 ± 80 80 1 2 40 80 1.6 3.2 TA = 25°C 25°C VCC = MAX VCC = 7 V 40 90 47 65 120 65 85 40 90 47 65 IOH = 10 mA IOH = 40 mA VIL = 0.8 V, 2.4 2 MIN SN55113 TYP MAX 0.9 3.4 3.0 0.23 1.1 1 0.4 1.5 10 200 1 10 20 ± 10 20 ± 20 ± 20 20 1 mA 2 40 80 1.6 3.2 120 65 85 µA mA mA mA µA µA 1.5 2.4 2 MIN SN75113 TYP MAX 0.9 3.4 3.0 0.23 1.1 0.4 1.5 1.5 UNIT V V V V
Off-state IO(off) open-collector output output current
TA = MAX MAX
IIH IIL IOS ICC
VCC = MAX MAX, VCC = MAX MAX, VCC = MAX MAX,
VI = 2 4 V 2.4 VI = 0 4 V 0.4 VO = 0 0,
All inputs at 0 V, No load, TA = 25°C
All parameters with the exception of off-state open-collector output current are measured with the active pullup connected to the sink output. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions. All typical values are at TA = 25°C and VCC = 5 V, with the exception of VCC at 7 V. § Only one output should be shorted at a time, and duration of the short-circuit should not exceed one second.
4
POST OFFICE BOX 655303
· DALLAS, TEXAS 75265
SN55113, SN75113 DUAL DIFFERENTIAL LINE DRIVERS
SLLS070C SEPTEMBER 1973 REVISED MARCH 1997
switching characteristics, VCC = 5 V, CL = 30 pF, TA = 25°C
PARAMETER tPLH tPHL tPZH tPZL tPHZ tPLZ Propagation delay time, low-to-high level output Propagation delay time, high-to-low-level output Output enable time to high level Output enable time to low level Output disable time from high level Output disable time from low level TEST CONDITIONS CONDITIONS See Figure 1 Figure RL = 180 , See Figure 2 RL = 250 , See Figure 3 RL = 180 , See Figure 2 RL = 250 , See Figure 3 SN55113 MIN TYP 13 12 7 14 10 17 MAX 20 20 15 30 20 35 MIN SN75113 TYP 13 12 7 14 10 17 MAX 30 30 20 40 30 35 UNIT ns ns ns ns ns ns
PARAMETER MEASUREMENT INFORMATION
5V 1 k
Input
AND Output CL = 30 pF (see Note B) NAND Output CL = 30 pF (see Note B) TEST CIRCUIT
Pulse Generator (see Note A) 50
5 ns 90% Input 10% tPHL NAND Output tPLH 1.5 V 90% 1.5 V
5 ns 3V
10% tPLH
0V VOH
1.5 V
1.5 V VOL tPHL VOH
AND Output
1.5 V
1.5 V VOL
VOLTAGE WAVEFORMS NOTES: A. The pulse generator has the following characteristics: ZO = 50 , PRR 500 kHz, tw = 100 ns. B. CL includes probe and jig capacitance.
Figure 1. Test Circuit and Voltage Waveforms tPLH and tPHL
POST OFFICE BOX 655303
· DALLAS, TEXAS 75265
5
Others parts begin by 59
59-1 59-2 59-3 59-4 59-5 59-6 59-7 59-8 59-9 59-10 59-11 59-12 59-13 59-14 59-15 59-16 59-17 59-18 59-19 59-20 59-21 59-22 59-23 59-24 59-25
|
|
|
