|
|
Part: 5962-8995701VA
Category:
Power Management
-> Motor Controller/Drivers
-> Motion/Motor Control
Description: ti UC1637, Switched Mode Controller For DC Motor Drive
Company: Texas Instruments, Inc.
Datasheet: Download 5962-8995701VA datasheet File size : 224 kB
Request For quote: Find where to buy 5962-8995701VA
Datasheet text preview:
UC1637 UC2637 UC3637
Switched Mode Controller for DC Motor Drive
FEATURES
· · · Single or Dual Supply Operation ±2.5V to ±20V Input Supply Range ±5% Initial Oscillator Accuracy; ± 10% Over Temperature Pulse-by-Pulse Current Limiting Under-Voltage Lockout Shutdown Input with Temperature Compensated 2.5V Threshold Uncommitted PWM Comparators for Design Flexibility Dual 100mA, Source/Sink Output Drivers
DESCRIPTION
The UC1637 is a pulse width modulator circuit intended to be used for a variety of PWM motor drive and amplifier applications requiring either uni-directional or bidirectional drive circuits. When used to replace conventional drivers, this circuit can increase efficiency and reduce component costs for many applications. All necessary circuitry is included to generate an analog error signal and modulate two bi-directional pulse train outputs in proportion to the error signal magnitude and polarity. This monolithic device contains a sawtooth oscillator, error amplifier, and two PWM comparators with ±100mA output stages as standard features. Protection circuitr y includes under-voltage lockout, pulse-by-pulse current limiting, and a shutdown port with a 2.5V temperature compensated threshold. The UC1637 is characterized for operation over the full military temperature range of -55°C to +125°C, while the UC2637 and UC3637 are characterized for -25°C to +85°C and 0°C to +70°C, respectively.
· · ·
·
ABSOLUTE MAXIMUM RATINGS (Note 1)
·
BLOCK DIAGRAM
Supply Voltage (±Vs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20V Output Current, Source/Sink (Pins 4, 7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500mA Analog Inputs (Pins 1, 2, 3, 8, 9, 10, 11 12, 13, 14, 15, 16) . . . . . . . . . . . . . . . . . . . . . . . ±Vs Error Amplifier Output Current (Pin 17) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20mA Oscillator Charging Current (Pin 18). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -2mA Power Dissipation at TA = 25°C (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000mW Power Dissipation at TC = 25°C (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000mW Storage Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65°C to +150°C Lead Temperature (Soldering, 10 Seconds). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +300°C Note 1: Currents are positive into, negative out of the specified terminal. Note 2: Consult Packaging Section of Databook for thermal limitations and considerations of package.
6/97
CONNECTION DIAGRAM
DIL-18 (TOP VIEW) J or N Package PLCC-20, LCC-20 (TOP VIEW) Q, L Packages
UC1637 UC2637 UC3637
PACKAGE PIN FUNCTION FUNCTION PIN
SOIC-20 (TOP VIEW) DW Package
+VTH CT -VTH AOUT -VS N/C +VS BOUT +BIN -BIN -AIN +AIN +C/L -C/L SHUTDOWN N/C +E/A -E/A E/A OUTPUT ISET
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
ELECTRICAL CHARACTERISTICS: Unless otherwise stated, these specifications apply for TA = -55°C to +125°C for the
UC1637; -25°C to +85°C for the UC2637; and 0°C to +70°C for the UC3637; +VS = +15V, -VS = - 15V, +VTH = 5V, -VTH = -5V, RT = 16.7k, CT = 1500pF, TA=TJ. PARAMETER Oscillator Initial Accuracy Voltage Stability Temperature Stability +VTH Input Bias Current -VTH Input Bias Current +VTH, -VTH Input Range Error Amplifier Input Offset Voltage Input Bias Current Input Offset Current Common Mode Range Open Loop Voltage Gain Slew Rate Unity Gain Bandwidth CMRR PSRR Over Common Mode Range VS = ±2.5 to ±20V 75 75 VCM = 0V VCM = 0V VCM = 0V VS = ±2.5 to 20V RL = 10k -VS+2 75 100 15 2 100 110 75 75 1.5 0.5 0.1 5 5 1 +VS -VS+2 80 100 15 2 100 110 1.5 0.5 0.1 10 5 1 +VS mV µA µA V dB V/µS MHz dB dB TJ = 25°C (Note 6) VS = ±5V to ±20V, VPIN 1 = 3V, VPIN 3 = -3V Over Operating Range (Note 3) VPIN 2 = 6V VPIN 2 = 0V -10 -10 +VS-2 9.4 10 5 0.5 0.1 -0.5 10.6 7 2 10 -10 -10 -VS+2 +VS-2 9 10 5 0.5 0.1 -0.5 -VS+2 11 7 2 10 kHz % % µA µA V TEST CONDITIONS UC1637/UC2637 MIN TYP MAX MIN UC3637 TYP MAX UNITS
2
UC1637 UC2637 UC3637 ELECTRICAL CHARACTERISTICS: Unless otherwise stated, these specifications apply for TA = -55°C to +125°C for the
UC1637; -25°C to +85°C for the UC2637; and 0°C to +70°C for the UC3637: VS = +15V, -VS = - 15V, +VTH = 5V, -VTH = -5V, RT = 16.7k, CT = 1500pF, TA=TJ. PARAMETERS Error Amplifier (Continued) Output Sink Current Output Source Current High Level Output Voltage Low Level Output Voltage PWM Comparators Input Offset Voltage Input Bias Current Input Hysteresis Common Mode range Current Limit Input Offset Voltage Input Offset Voltage T.C. Input Bias Current Common Mode Range Shutdown Shutdown Threshold Hysteresis Input Bias Current Under-Voltage Lockout Start Threshold Hysteresis Total Standby Current Supply Current Output Section Output Low Level Output High Level Rise Time Fall Time ISINK = 20mA ISINK = 100mA ISOURCE = 20mA ISOURCE = 100mA (Note 3) CL = Inf, TJ = 25°C (Note 3) CL = Inf, TJ = 25°C 13 12 -14.9 -14.5 13.5 13.5 100 100 600 300 -13 -13 13 12 -14.9 -14.5 13.5 13.5 100 100 600 300 ns ns -13 -13 V V 8.5 15 8.5 15 mA (Note 5) 4.15 0.25 5.0 4.15 0.25 5.0 V mV VPIN 14 = +VS to -VS -10 (Note 4) -2.3 -2.5 40 -0.5 -10 -2.7 -2.3 -2.5 40 -0.5 -2.7 V mV µA VS = ±2.5V to ±20V -10 -VS VCM = 0V, TJ = 25°C 190 200 -0.2 -1.5 +VS-3 -10 -VS 210 180 200 -0.2 -1.5 +VS-3 220 mV mV/°C µA V VCM = 0V VCM = 0V VCM = 0V VS = ±5V to ±20V -VS+1 20 2 10 +VS-2 -VS+1 10 20 2 10 +VS-2 10 mV µA mV V VPIN 17 = 0V VPIN 17 = 0V 5 13 -50 11 13.6 -14.8 -13 -20 5 13 -50 11 13.6 -14.8 -13 -20 mA mA V V TEST CONDITIONS UC1637/UC2637 MIN TYP MAX MIN UC3637 TYP MAX UNITS
Note 3: Note 4: Note 5: Note 6:
These parameters, although guaranteed over the recommended operating conditions, are not 100% tested in production. Parameter measured with respect to +VS (Pin 6). Parameter measured at +VS (Pin 6) with respect to -VS (Pin 5). RT and CT referenced to Ground.
FUNCTIONAL DESCRIPTION
Following is a description of each of the functional blocks shown in the Block Diagram. Oscillator The oscillator consists of two comparators, a charging and discharging current source, a current source set terminal, lSET and a flip-flop. The upper and lower threshold of the oscillator waveform is set externally by applying a voltage at pins +VTH and -VTH respectively. The +VTH ter3 minal voltage is buffered internally and also applied to the lSET terminal to develop the capacitor charging current through RT. If RT is referenced to -VS as shown in Figure 1, both the threshold voltage and charging current will vary proportionally to the supply differential, and the oscillator frequency will remain constant. The triangle waveform oscillators frequency and voltage amplitude is determined by the external components using the formulas given in Figure 1.
UC1637 UC2637 UC3637
Figure 1. Oscillator Setup PWM Comparators Two comparators are provided to perform pulse width modulation for each of the output drivers. Inputs are uncommitted to allow maximum flexibility. The pulse width of the outputs A and B is a function of the sign and amplitude of the error signal. A negative signal at Pin 10 and 8 will lengthen the high state of output A and shorten the high state of output B. Likewise, a positive error signal reverses the procedure. Typically, the oscillator waveform is compared against the summation of the error signal and the level set on Pin 9 and 11.
MODULATION SCHEMES
Case A Zero Deadtime (Equal voltage on Pin 9 and Pin 11) In this configuration, maximum holding torque or stiffness and position accuracy is achieved. However, the power input into the motor is increased. Figure 3A shows this configuration. Case B Small Deadtime (Voltage on Pin 9 > Pin 11) A small differential voltage between Pin 9 and 11 provides the necessary time delay to reduce the chances of momentary short circuit in the output stage during transitions, especially where power-amplifiers are used. Refer to Figure 3B. Case C Increased Deadtime and Deadband Mode (Voltage on Pin 9 > Pin 11) With the reduction of stiffness and position accuracy, the power input into the motor around the null point of the servo loop can be reduced or eliminated by widening the window of the comparator circuit to a degree of acceptance. Where position accuracy and mechanical stiffness is unimportant, deadband operation can be used. This is shown in Figure 3C.
Figure 2. Comparator Biasing Output Drivers Each output driver is capable of both sourcing and sinking 100mA steady state and up to 500mA on a pulsed basis for rapid switching of either POWERFET or bipolar transistors. Output levels are typically -VS + 0.2V @50mA low level and +VS - 2.0V @50mA high level. Error Amplifier The error amplifier consists of a high slew rate (15V/µs) op-amp with a typical 1MHz bandwidth and low output impedance. Depending on the ±VS supply voltage, the common mode input range and the voltage output swing is within 2V of the VS supply. Under-Voltage Lockout An under-voltage lockout circuit holds the outputs in the low state until a minimum of 4V is reached. At this point, all internal circuitry is functional and the output drivers are enabled. If external circuitry requires a higher starting voltage, an over-riding voltage can be programmed through the shutdown terminal as shown in Figure 4.
4
UC1637 UC2637 UC3637
Figure 3. Modulation Schemes Showing (A) Zero Deadtime (B) Deadtime and (C) Deadband Configurations Shutdown Comparator The shutdown terminal may be used for implementing various shutdown and protection schemes. By pulling the terminal more than 2.5V below VIN, the output drivers will be enabled. This can be realized using an open collector gate or NPN transistor biased to either ground or the negative supply. Since the threshold is temperature stabilized, the comparator can be used as an accurate low voltage lockout (Figure 4) and/or delayed start as in Figure 5. In the shutdown mode the outputs are held in the low state. Figure 5. Delayed Start-Up -VS to within 3V of the +VS supply while providing excellent noise rejection. Figure 6 shows a typical current sense circuit.
Figure 4. External Under-Voltage Lockout Current Limit A latched current limit amplifier with an internal 200mV offset is provided to allow pulse-by-pulse current limiting. Differential inputs will accept common mode signals from
Figure 6. Current Limit Sensing 5
Others parts begin by 59
59-1 59-2 59-3 59-4 59-5 59-6 59-7 59-8 59-9 59-10 59-11 59-12 59-13 59-14 59-15 59-16 59-17 59-18 59-19 59-20 59-21 59-22 59-23 59-24 59-25
|
|
|
