Details, datasheet, quote on part number: 74AC11160N
CategoryLogic => Counters => Binary Counters
Descriptionti 74AC11160, Synchronous 4-Bit Decade Counters
CompanyTexas Instruments, Inc.
DatasheetDownload 74AC11160N datasheet
Find where to buy


Features, Applications

Internal Look-Ahead for Fast Counting Carry Output for n-Bit Cascading Fully Synchronous Operation for Counting Flow-Through Architecture to Optimize PCB Layout Center-Pin VCC and GND Pin Configurations Minimize High-Speed Switching Noise EPIC TM (Enhanced-Performance Implanted CMOS) 1-m Process 500-mA Typical Latch-Up Immunity at 125C Package Options Include Plastic Small-Outline Packages and Standard Plastic 300-mil DIPs


This synchronous, presettable 4-bit decade counter features an internal carry look-ahead circuitry for application in high-speed counting designs. Synchronous operation is provided by having all flip-flops clocked simultaneously so that the outputs change coincident with each other when so instructed by the count-enable inputs and internal gating. This mode of operation eliminates the output counting spikes that are normally associated with asynchronous (ripple clock) counters; however, counting spikes may occur on the ripple carry out output (RCO). A buffered clock input triggers the four flip-flops on the rising (positive-going) edge of the clock input waveform. This counter is fully programmable in that they may be preset to any number between 0 and 9. As presetting is synchronous, setting up a low level at the load input disables the counter and causes the outputs to agree with the setup data after the next clock pulse, regardless of the levels of the enable inputs. The clear function for the 74AC11160 is synchronous and a low level at the clear input sets all four of the flip-flops outputs low, regardless of the levels of the clock, load, or enable inputs. If one of these decade counters is preset to a number between 10 and 15 or assumes such an invalid state when power is applied, it will progress to the normal sequence within two counts as shown in the state diagram. The carry look-ahead circuitry provides for cascading counters for n-bit synchronous applications without additional gating. Instrumental in accomplishing this function are two count-enable inputs and a ripple carry output. Both count-enable inputs (ENP and ENT) must be high to count, and ENT is fed forward to enable the ripple carry output (RCO). RCO thus enabled will produce a high-level pulse while the count is 9 (HLLH). This high-level overflow ripple carry pulse can be used to enable successive cascaded stages. Transitions at the ENP or ENT are allowed regardless of the level of the clock input. This counter features a fully independent clock circuit. Changes at control inputs (ENP, ENT, or LOAD) that will modify the operating mode have no effect on the contents of the counter until clocking occurs. The function of the counter (whether enabled, disabled, loading, or counting) will be dictated solely by the conditions meeting the setup and hold times. The 74AC11160 is characterized for operation from to 85C.

PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.

This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.


Some Part number from the same manufacture Texas Instruments, Inc.
74AC11162 Synchronous 4-bit Decade Counter
74AC11174 Hex D-type Flip-flop With Clear
74AC11174DW ti 74AC11174, 6-Bit Positive-edge-triggered D-type Flip-flops With Clear
74AC11175 Quadruple D-type Flip-flop With Clear
74AC11175DW ti 74AC11175, Quadruple Positive-edge-triggered D-type Flip-flops With Clear
74AC11181DW ti 74AC11181, Arithmetic Logic Units/function Generators
74AC11191 Synchronous 4-bit Up/down Binary Counter
74AC11191DW ti 74AC11191, Synchronous 4-Bit Up/down Binary Counters
74AC11194 4-bit Bidirectional Universal Shift Register
74AC11194DW ti 74AC11194, 4-Bit Bidirectional Universal Shift Registers
74AC11204-7DW ti 74AC11204, Clock Drivers, Hex Inverters
74AC11208-7DW ti 74AC11208, Dual 1-to-4 Clock Drivers With 3-State Outputs
74AC11238 3-line to 8-line Decoders/demultiplexer

CY54FCT574TDIP : 8-bit Registers

DRV134UA : Analog Line Drivers and Receivers ti DRV134, Audio Balanced Line Drivers

PTH12020WAH : 1.2 to 5.5 V 18-A, 12-V Input Non-isolated Wide-adjust Module

SN74ABT16240ADGV : 16-bit Buffers/drivers With 3-state Outputs

TMS44400DJ-70 : Asynchronous->5V FPM 1 048 576-word BY 4-bit DRAM

CY74FCT2574CTSOCG4 : 8-bit Registers WITH 3-state Outputs

TLV320AIC31IRHBTG4 : IC, AUDIO CODEC, 24BIT, 96KHZ, QFN-32 Specifications: Audio CODEC Type: Stereo ; No. of ADCs: 2 ; No. of DACs: 2 ; No. of Input Channels: 6 ; No. of Output Channels: 6 ; ADC / DAC Resolution: 24bit ; ADCs / DACs Signal to Noise Ratio: 100dB ; Sampling Rate: 96kSPS ; IC Interface Type: I2C ; Supply Voltage Range: 2.7V to 3.6V, 1.65V to 1

TLV320AIC3256EVM-U : Very Low Power Stereo Audio CODEC With Power TuneTM Technology The TLV320AIC3204 (sometimes referred to as the AIC3204) is a flexible low-power, low-voltage stereo audio codec with programmable inputs an outputs, PowerTune capabilities, fixed predefined and parameterizable signal processing blocks,

UCC2894DRG4 : Pmic - Voltage Regulator - Dc Dc Switching Controller Integrated Circuit (ics) Current Mode Tape & Reel (TR) 1 8.5 V ~ 16 V; IC PWM FLYBCK ISOLATED CM 16SOIC Specifications: PWM Type: Current Mode ; Number of Outputs: 1 ; Package / Case: 16-SOIC (0.154", 3.90mm Width) ; Packaging: Tape & Reel (TR) ; Duty Cycle: 74% ; Voltage - Supply: 8.5 V ~ 16 V ; Frequency - Max: 1MHz ; Buck: No ; Boost: No ; Flyback: Yes ; Inverting: No ; Doubler: No ; Divider: N

0-C     D-L     M-R     S-Z