Details, datasheet, quote on part number: MSP430F133IPAG
CategorySemiconductors => Microcontrollers (MCU) => MSP430 ultra-low-power MCUs => MSP430F1x
Part familyMSP430F133 16-Bit Ultra-Low-Power Microcontroller, 8kB Flash, 256B RAM, 12 bit ADC, USART
TitleUltra-Low Power Microcontrollers
Description16-Bit Ultra-Low-Power Microcontroller, 8kB Flash, 256B RAM, 12 bit ADC, USART 64-TQFP -40 to 85
CompanyTexas Instruments, Inc.
DatasheetDownload MSP430F133IPAG datasheet
Find where to buy
Timers - 32-bit0
Active Power (uA/MHz)280
Operating Temperature Range(C)-40 to 85
GPIO Pins(#)48
FeaturesWatchdog,Temp Sensor
Timers - 16-bit2
Min VCC1.8
Max VCC3.6
Non-volatile Memory (KB)8
ADCADC12 - 8ch
Approx. Price (US$)3.00 | 1ku
Wakeup Time (us)6
Special I/ON/A
Standby Power (LPM3-uA)1.6
  Mecanical Data
Pin nbPackage typeInd stdJEDEC codePackage qtyCarrierDevice markWidth (mm)Length (mm)Thick (mm)Pitch (mm)
64PAGTQFPS-PQFP-G160JEDEC TRAY (10+1)M430F133 10101.5
Application notes
• MSP430 SMBus
This application report describes a software implementation of the system management bus (SMBus) for the MSP430 microcontroller. It includes all master protocols, an interrupt-driven slave, and master usage examples. SMBus is derived from the I2C and is co | Doc
• MSP430 Isolated FET Interface
This application report describes how to build an isolated FET interface for the MSP430 Flash Emulation Tool (FET). When developing and debugging line-powered MSP430applications such as motor control, electricity energy meters, power monitoring systems etc | Doc
• HDQ Protocol Implementation with MSP430 | Doc
• FSK Modulation and Demodulation With the Microcontroller MSP430
This application report describes a software program for performing V.23 FSK modem transceiver functions using an MSP430 microcontroller. It makes use of novel filter architecture to perform DSP functions on a processor with only shift and add capabilities | Doc
• A Low-Cost 12-bit Speech CODEC Using the MSP430F13x
This application report illustrates a design of a single chip speech codec (ADC and DAC) using the MSP430F133 MCU from Texas Instruments. The ADC part of this codec uses the on chip 12-bit ADC. The DAC part uses a novel PWM technique which enables the DAC | Doc
• MSP430 32-kHz Crystal Oscillators (Rev. D)
Selection of the right crystal, correct load circuit, and proper board layout are important for a stable crystal oscillator. This application report summarizes crystal oscillator function and explains the parameters to select the correct crystal for ultra- | Doc
• Powering the MSP430 from a High Voltage Input using the TPS62122 (Rev. C) | Doc
• Generation and Recognition of DTMF Signals With the Microcontroller MSP430
The first part of the Application Report describes the generation of DTMF signals using the Microcontroller MSP430. Following an explanation of the most important specifications which are involved, the theoretical and mathematical processes will be discuss | Doc
• General Oversampling of MSP ADCs for Higher Resolution (Rev. A)
Multiple MSP ultra-low-power microcontrollers offer analog-to-digital converters (ADCs) to convert physical quantities into digital numbers, a function that is widely used across numerous applications. There are times, however, when a customer design deman | Doc
• Advanced Debugging Using the Enhanced Emulation Module (EEM) With CCS v6 (Rev. F) | Doc
• Simple 1.5 V Boost Converter for MSP430
A simple, efficient, low-cost, boost converter to take 1.5 V from a single type-AA alkaline battery to the operating voltage required by the MSP430 family of ultralow-power microcontrollers is described. Expected battery life is up to 1000 hours. | Doc
• Efficient MSP430 Code Synthesis for an FIR Filter
Digital filtering can be easily accomplished on the MSP430 using efficient multiplication. The tool accompanying this document automatically converts FIR filter coefficients to MSP430 assembly code that can be used in any application. Horner’s method and | Doc
• Wave Digital Filtering Using the MSP430
Digital filtering is an integral part of many digital signal processing algorithms. Digital filters are characterized as either recursive [infinite impulse response (IIR)] or non-recursive [finite impulse response (FIR)] filters. IIR filters require a smal | Doc
• MSP Code Protection Features
MSP microcontrollers (MCUs) offer a number of features to help control code accessibility in the device, to add different layers of code access management and protection strategies. These include features that can lock or password protect the JTAG/SBW acce | Doc
• Economic Voltage Measurement With the MSP430 Family
This application report describes voltage and current measurement methods using the MSP430 universal timer/port module. The report explains the two measurement methods (charge and discharge) and shows how to measure voltage and current. The equations for t | Doc
• 1.8V – 5.5V Input, High-Efficiency DCDC Converter Reference Design for MSP430 (Rev. B)
This reference design is presented to help application designers and others who are trying to use the MSP430 in a system with an input voltage in the range of 1.8 V to 5.5 V, and who must increase the application run time by making use of the complete batt | Doc
• Design Considerations When Using the MSP430 Graphics Library
LCDs are a growing commodity in todays market with products as diverse as children's toys to medical devices. Modern LCDs, along with the graphics displayed on them, are growing in complexity. A graphics library can simplify and accelerate development whil | Doc
• Digital Fan Control With Tachometer Using MSP430
Digital Fan Control with Tachometer using MSP430 Application Report | Doc
• Spread-Spectrum Clock Source Using an MSP430
While spread-spectrum clocking has long since been used in processor and memory clock trees, there are many other clocked systems, such as power supplies or switch-mode amplifiers, that continue to use a single-frequency clock. This can, in turn, generate | Doc
• Using the TPS3619 with MSP430 Microcontrollers Can Reduce Sys Power Consumption (Rev. A)
The MSP430 series of microcontrollers are ideal in applications where battery life is critical. These microcontollers require only 0.1?A of current in low-power RAM retention mode; In this mode the microcontroller must have power to retain volatile memor | Doc
• Tiny DCDC Converter Reference Design (Rev. A)
This reference design is presented to help application designers and others who are trying to use the MSP430 in a system with an input voltage in the range of 3.6 V to 6 V with the primary design objective to minimize solution size as well as to maintain h | Doc
• AES128 – A C Implementation for Encryption and Decryption (Rev. A)
This application report describes the AES algorithm and the use of a suggested C implementation for AES encryption and decryption with MSP430.Note: This document may be subject to the export control policies of the local government. | Doc
• Interfacing TMS320C5000 DSP to MSP430 Mixed Signal Microcontroller (Rev. A)
The TMS320C5000™ family of digital signal processors (DSPs) features Host Port Interface Controllers (HPI) and Direct Memory Access Controllers (DMAC) for efficient data movement without any CPU involvement. The HPI enables the DSP to interface to host p | Doc
• MSP430 LFXT1 Oscillator Accuracy
This report details the factors that influence achievable accuracy of the low frequency oscillator, specifically for real-time clock (RTC) applications. The intent of this application report is to provide an understanding of MSP430-specific factors influen | Doc
• Interfacing the 3-V MSP430 to 5-V Circuits
The interfacing of the 3-V MSP430x1xx and MSP430x4xx microcontroller families to circuits with a supply of 5 V or higher is shown. Input, output and I/O interfaces are given and explained. Worse-case design equations are provided, where necessary. Some sim | Doc
• Programming a Flash-Based MSP430 Using the JTAG Interface (Rev. H)
This application report has been superseded by the document shown below. Information previously contained in this application report can be found by clicking on the following links.- MSP430 Programming Via the JTAG Interface User's Guide Download MSP430 P | Doc
• Mixing C and Assembler with the MSP430
This application note describes how C and assembler code can be used together within an MSP430 application. The combination of C and assembler benefits the designer by providing the power of a high-level language as well as the speed, efficiency, and low-l | Doc
• Efficient Multiplication and Division Using MSP430 | Doc
• ESD Diode Current Specification
This document explains the maximum ESD diode current specified for GPIO on MSP microcontrollers. Sometimes signals on specific pins exceed the supply of the MSP MCU. In such a case, the device can handle this overvoltage condition through the ESD diodes, b | Doc
• Implementing An Ultralow-Power Keypad Interface with MSP430
Often in applications with keypads, the condition can occur where a key can be held or stuck down, causing excess current consmption and reducing the battery life of a battery-operated product. This application report shows a solution. The keypad interfa | Doc
• MSP430 Embedded Application Binary Interface
This document is a specification for the ELF-based Embedded Application Binary Interface (EABI) for the MSP430 family of processors from Texas Instruments. The EABI defines the low-level interface between programs, program components, and the execution env | Doc
• Choosing an Ultra Low-Power MCU
This application report describes how to compare ultralow-power MCUs. It discusses the key differences between popular low-power MCUs and how to interpret features and specifications and apply them to application requirements. | Doc
• Interfacing the MSP430 and TLC549/1549 A/D Converters
This application report describes how to interface an MSP430 mixed-signal microcontroller with the TLC549 and TLV1549 3-volt A/D converters. This report is written for the MSP430x11x(1) family, but can be adapted to any MSP430 derivative. | Doc
• Boost DC/DC with Ultra-Low Shutdown Current (Rev. A)
This reference design is presented to help application designers and others who are trying to use the MSP430 in a system that requires a very low input voltage range while also maintaining high efficiency. Battery life is extended as well as a result of th | Doc
• Current Transformer Phase Shift Compensation and Calibration
This application report demonstrates a digital technique to compensate and calibrate the phase shift of a current (or voltage) transformer used in electric power of energy measurement. Traditional analog compensation is replaced by a digital finite impulse | Doc
• MSP430 Family Mixed-Signal Microcontroller Application Reports
MSP430 Metering Application Report | Doc
• Li-Ion Battery Charger solution using the MSP430 | Doc
• MSP430 Software Coding Techniques (Rev. A)
This application report covers software techniques and topics of interest to all MSP430 programmers. The first part of the document discusses the MSP430 standard interrupt-based code flow model, recommended for the vast majority of applications. The next p | Doc
• MSP430 Capacitive Single-Touch Sensor Design Guide
This application report discusses the design of RC-type capacitive single-touch sensors using the MSP430 microcontroller. The MSP430 has some unique features that make it suitable for interfacing with capacitive-touch sensors. The RC-type method does not n | Doc
• MSP430 Flash Memory Characteristics (Rev. A)
Flash memory is a widely used, reliable, and flexible nonvolatile memory to store software code and data in a microcontroller. Failing to handle the flash according to data-sheet specifications may result in unreliable operation of the application. This ap | Doc
• Understanding MSP430 Flash Data Retention
The MSP430 family of microcontrollers, as part of its broad portfolio, offers both read-only memory (ROM)-based and flash-based devices. Understanding the MSP430 flash is extremely important for efficient, robust, and reliable system design. Data retention | Doc
• CRC Implementation with MSP430
Cyclic Redundancy Code (CRC) is commonly used to determine the correctness of a data transmission or storage. This application note presents a solution to compute 16-bit and 32-bit CRCs on the ultra low-power TI MSP430 microcontroller for the bitwise algor | Doc
• Random Number Generation Using the MSP430
Many applications require the generation of random numbers. These random numbers are useful for applications such as communication protocols, cryptography, and device individualization.Generating random numbers often requires the use of expensive dedicated | Doc
Evaluation Kits
MSP-FET430U64: 64-pin Target Development Board and MSP-FET Programmer Bundle - MSP430F1x, MSP430F2x, MSP430F4x MCUs
MSP-TS430PM64: MSP-TS430PM64 - 64-pin Target Development Board for MSP430F1x, MSP430F2x and MSP430F4x MCUs


Features, Applications

Low Supply-Voltage Range, 3.6 V Ultralow-Power Consumption: Active Mode: at 1 MHz, 2.2V Standby Mode: A Off Mode (RAM Retention): 0.1 A Five Power-Saving Modes Wake-Up From Standby Mode in less than s 16-Bit RISC Architecture, 125-ns Instruction Cycle Time 12-Bit A/D Converter With Internal Reference, Sample-and-Hold and Autoscan Feature 16-Bit Timer_B With Seven Capture/Compare-With-Shadow Registers 16-Bit Timer_A With Three Capture/Compare Registers On-Chip Comparator Serial Onboard Programming, No External Programming Voltage Needed Programmable Code Protection by Security Fuse

Serial Communication Interface (USART), Functions as Asynchronous UART or Synchronous SPI Interface Two USARTs USART1) MSP430x14x(1) Devices One USART (USART0) MSP430x13x Devices Family Members Include: MSP430F133: 8KB+256B Flash Memory, 256B RAM MSP430F135: 16KB+256B Flash Memory, 512B RAM MSP430F1471: 32KB+256B Flash Memory, 1KB RAM MSP430F1481: 48KB+256B Flash Memory, 2KB RAM MSP430F1491: 60KB+256B Flash Memory, 2KB RAM Available in 64-Pin Quad Flat Pack (QFP) For Complete Module Descriptions, See the MSP430x1xx Family User's Guide, Literature Number SLAU049

The MSP430F14x1 devices are identical to the MSP430F14x devices with the exception that the ADC12 module is not implemented.


The Texas Instruments MSP430 family of ultralow-power microcontrollers consist of several devices featuring different sets of peripherals targeted for various applications. The architecture, combined with five low power modes is optimized to achieve extended battery life in portable measurement applications. The device features a powerful 16-bit RISC CPU, 16-bit registers, and constant generators that attribute to maximum code efficiency. The digitally controlled oscillator (DCO) allows wake-up from low-power modes to active mode in less than 6 s. The MSP430x13x and the MSP430x14x(1) series are microcontroller configurations with two built-in 16-bit timers, a fast 12-bit A/D converter (not implemented on the MSP430F14x1 devices), one or two universal serial synchronous/asynchronous communication interfaces (USART), and 48 I/O pins. Typical applications include sensor systems that capture analog signals, convert them to digital values, and process and transmit the data to a host system. The timers make the configurations ideal for industrial control applications such as ripple counters, digital motor control, EE-meters, hand-held meters, etc. The hardware multiplier enhances the performance and offers a broad code and hardware-compatible family solution.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.



Related products with the same datasheet
Some Part number from the same manufacture Texas Instruments, Inc.
MSP430F133IPM ti MSP430F133, 16-Bit Ultra-low-power Microcontroller, 8kB Flash, 256B RAM, 12 Bit ADC, Usart
MSP430F135 Ultra-low Power Microcontroller
MSP430F135IPAG ti MSP430F135, 16-Bit Ultra-low-power Microcontroller, 16kB Flash, 512B RAM, 12 Bit ADC, Usart
MSP430F147 Ultra-low Power Microcontroller
MSP430F1471IPM ti MSP430F1471, 16-Bit Ultra-low-power Microcontroller, 32 KB Flash, 1KB RAM, 2 Usarts, HW Multiplier
MSP430F147IPAG ti MSP430F147, 16-Bit Ultra-low-power Microcontroller, 32 KB Flash, 1KB RAM, 12 Bit ADC, 2 Usarts, HW Multiplier
MSP430F148 Ultra-low Power Microcontroller
MSP430F1481IPM ti MSP430F1481, 16-Bit Ultra-low-power Microcontroller, 48 KB Flash, 2KB RAM, 2 Usarts, HW Multiplier
MSP430F148IPAG ti MSP430F148, 16-Bit Ultra-low-power Microcontroller, 48 KB Flash, 2KB RAM, 12 Bit ADC, 2 Usarts, HW Multiplier
MSP430F149 Ultra-low Power Microcontroller
MSP430F1491IPM ti MSP430F1491, 16-Bit Ultra-low-power Microcontroller, 60 KB Flash, 2KB RAM, 2 Usarts, HW Multiplier
MSP430F149IPAG ti MSP430F149, 16-Bit Ultra-low-power Microcontroller, 60 KB Flash, 2KB RAM, 12 Bit ADC, 2 Usarts, HW Multiplier
MSP430F155 Ultra-low Power Microcontroller
MSP430F155IPM ti MSP430F155, 16-bit Ultra-low-power MCU, 16kB Flash, 512B RAM, 12-Bit ADC, Dual 12-Bit DAC, Usart, I2C, Dma

OPAY111 : ti OPAY111, Low Noise Precision DiFET Operational Amplifier Family

SN75ALS170ADWR : SCSI Parallel Interface (SPI) ti SN75ALS170A, Triple Differential Bus Transceiver

TLC070IDR : ti TLC070, Single Wide-bandwidth High-output-drive op Amp W/shutdown

TP3057ADWR : POTS and Linecard Codecs ti TP3057A, A-law, Single-ended Output, 1.536, 1.544, 2.048 Mhz, Enhanced Noise Reduction

TPS71727DCKTG4 : Low Noise, High-bandwidth PSRR Low-dropout 150ma Linear Regulator

OPA2703PAG4 : Linear - Amplifier - Instrumentation, Op Amps, Buffer Amp Integrated Circuit (ics) General Purpose Tube 160A 4 V ~ 12 V, 2 V ~ 6 V; IC OPAMP GP R-R 1MHZ DUAL 8DIP Specifications: Packaging: Tube ; Amplifier Type: General Purpose ; Number of Circuits: 2 ; Package / Case: 8-DIP (0.300", 7.62mm) ; Slew Rate: 0.6 V/s ; Gain Bandwidth Product: 1MHz ; Current - Supply: 160A ; Current - Output / Channel: 10mA ; Voltage - Supply, Single/Dual (): 4 V ~ 12 V, 2 V ~

UC2845ADG4 : Pmic - Voltage Regulator - Dc Dc Switching Controller Integrated Circuit (ics) Current Mode Tube 1 8.2 V ~ 25 V; IC PWM BOOST FLYBACK CM 14SOIC Specifications: PWM Type: Current Mode ; Number of Outputs: 1 ; Package / Case: 14-SOIC (0.154", 3.90mm Width) ; Packaging: Tube ; Duty Cycle: 50% ; Voltage - Supply: 8.2 V ~ 25 V ; Frequency - Max: 500kHz ; Buck: No ; Boost: Yes ; Flyback: Yes ; Inverting: No ; Doubler: No ; Divider: No ; Cuk: No ;

ADS7870IDBR : 8-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO28 Specifications: Package Type: SSOP, PLASTIC, SSOP-28 ; Screening Level: Industrial ; Pins: 28 ; Operating Temperature: -40 to 85 C (-40 to 185 F) ; Sample Rate: 52 kSamples/Sec ; Input Voltage: -0.2000 to 5.7 volts

Same catergory

80C652 : RISC->PICmicro Family. 80C652; 83C652; CMOS Single-chip 8-bit Microcontrollers.

83C51RC+ : 80c51 8-bit Microcontroller Family 8k.64k/256.1k Otp/rom/romless, Low Voltage 2.7v.5.5v, Low Power, High Speed 33 MHZ.

AT94KSeries : RISC->RISC. Field Programmable System Level Integrated Circuit: 10k - 40k Gates of At40k Fpga With 8-bit Microcontroller And 36k Bytes of SRAM.

CXP86400 : CMOS 8-bit Single Chip Microcomputer Piggyback/ Evaluator Type. The CXP86400/86490 are CMOS 8-bit single chip microcomputers that serve as both piggyback and evaluator. The CXP86400/86490 are developed for evaluating the function of the CXP86440/86448/86460. Note that the CXP86400 corresponds to the fixed font and the CXP86490 corresponds to the custom font respectively. 64 pin PQFP (Ceramic) A wide instruction.

HE80068L : for Speech Application. ROM Type = Mask ;; Application = Voice ;; Voice Duration = 68 Sec ;; ROM = 208KB ;; RAM = 128B ;; I/o = 24.

HE89410 : Telecom Application MCU. LCD Dots = -- ;; Reg. = -- ;; LCD Type = -- ;; ROM = 4K ;; RAM = 256 ;; I/o = 12 ;; Vo = -- ;; PWM = -- ;; Op = -- ;; Dao = -- ;; Timer(16-bits) = T1,T2,TB ;; WDT = ;; DTMF = ;; Remark =.

MSM6422 : High Speed And Simple 4-bit Microcontroller. This version: Sep. 1998 MSM6422 Previous version: Mar. 1996 The is a low-power, single-chip device implemented in complementary metal-oxide semiconductor technology. The MSM6422 can be used in place of logic ICs configured around a main CPU, or for small-scale systems such as home electronic equipment. ROM RAM I/O port Input-output port : 2048 words.

PIC16F870 : PICmicro with analog capability. This Powerful (200 Nanosecond Instruction Execution) Yet Easy-to-program (only 35 Single Word Instructions) CMOS Flash-based 8-bit Microcontroller Packs Microchip's Powerful Pic Architecture Into an 28-pin Package And is Upwards Compatible With The PIC16C5X, PIC12CXXX And PIC16C7X Devices.

S3C7515 : S3C7(KS57) Series. = S3C7515 ;; ROM(KB) = 16 ;; RAM Nibble = 512 ;; I/o Pins = 55 ;; Interrupt (Int/Ext) = 4/3 ;; Timer/counters = BT/WT/8Tx2 ;; Sio = Yes ;; LCD (Seg/Com) = - ;; ADC (BitxCh) = - ;; PWM(BitxCh) = - ;; Max. OSC.Freq. (MHz) = 6 ;; VDD(V) = 2.0~5.5 ;; Other = Subsystem Clock,buz Output ;; Package = 64SDIP,64QFP ;; Production Status = Mass.

S3C80F9 : S3C8(KS88) Series. = S3C80F9 ;; ROM(KB) = 24,32 ;; RAM(bytes) = 272 ;; I/o Pins = 38 ;; Interrupt (Int/Ext) = 5/16 ;; Timer/counters = BT/8TC/16TC ;; Serial Interface = - ;; LCD (Seg/Com) = - ;; ADC (BitxCh) = - ;; PWM(BitxCh) = 8x1 ;; Max. OSC.Freq. (MHz) = 8 ;; VDD(V) = 2.0~5.0 ;; Other = LVD(2.2V),Carrier Generator ;; Package = 32SOP,42SDIP,44QFP,48ELP.

S3P9434 : S3C9(KS86) Series. = S3P9434 General Purpose 8 Bit Microcontroller ;; ROM(KB) = 4 ;; RAM(bytes) = 112 ;; I/o Pins = 11/13 ;; Interrupt (Int/Ext) = 3/2 ;; Timer/counters = BT/WDT/8T ;; Serial Interface = Sio ;; LCD (Seg/Com) = - ;; ADC (BitxCh) = 10x5 ;; PWM(BitxCh) = 12x1 ;; Max. OSC.Freq. (MHz) = 16 ;; VDD(V) = 3.0~5.5 ;; Other = RC Osc.,buzzer Output,lvd.

TMP87CK43N : TLCS-870 Series. ROM Size = 24K ;; RAM Size = 1K ;; Supply Voltage = 4.5-5.5/ 2.7-5.5 ;; I/o Count = 35 ;; Unique = 8-bit A/D Convert X6ch/Serial Bus Inter. ;; Additional Information = More Info.

TMP91PW11F : TLCS900/L1 Series. ROM Size = OTP 128K-byte ;; RAM Size = Null ;; Supply Voltage = - ;; I/o Count = - ;; Unique = - ;; Additional Information = More Info.

XC68HC08AZ0CPU : MC68HC08AZ0 Advance Information. List of Sections. 1 Table of Contents. 3 General . 9 Memory Map. 23 RAM. 35 EBI. 37 EEPROM. 55 Central Processor Unit (CPU). 67 System Integration Module (SIM). 85 Clock Generator Module (CGM). 107 Mask Options. 135 Break Module. 139 Monitor ROM (MON). 147 Computer Operating Properly Module (COP). 159 Low-Voltage Inhibit (LVI). 165 .

Z86C02 : ROM (KB)  = 0.5 ;; RAM  = 61 ;; Speed  = 8 ;; I/O  = 14 ;; 8-bit Timers  = 1 ;; Comm Interfaces  = -- ;; Other   = Por, LV Protect ;; Voltage  = 3.0-5.5V ;;.

Z8E000 : OTP (KB)  = 0.5 ;; RAM  = 32 ;; Speed  = 10 ;; I/O  = 13 ;; 8-bit Timers  = 1 ;; Comm Interfaces  = -- ;; Other   = -- ;; Voltage  = 3.5-5.5V ;;.

MC9S08DE60 : HCS08 Microcontrollers Controller Area NetworkMC9S08DE60 Series devices are primarily focused at safety based applications. The error code correction (ECC) based Flash provides the highest level of Flash quality for the automotive safety markets..

HT95R25 : Phone 8-Bit MCU The HT95R25 MCU is an 8-bit high performance, RISC architecture microcontroller device specially designed for telephone applications. Device flexibility is enhanced with their internal special such as power-down and wake-up functions, DTMF generator, PFD driver, etc. These combine to ensure applications require a minimum of external.

0-C     D-L     M-R     S-Z