Details, datasheet, quote on part number: MSP430F147IPAG
PartMSP430F147IPAG
CategorySemiconductors => Microcontrollers (MCU) => MSP430 ultra-low-power MCUs => MSP430F1x
Part familyMSP430F147 16-Bit Ultra-Low-Power Microcontroller, 32 kB Flash, 1KB RAM, 12 bit ADC, 2 USARTs, HW multiplier
TitleUltra-Low Power Microcontrollers
Description16-Bit Ultra-Low-Power Microcontroller, 32 kB Flash, 1KB RAM, 12 bit ADC, 2 USARTs, HW multiplier 64-TQFP -40 to 85
CompanyTexas Instruments, Inc.
StatusACTIVE
ROHSY
SampleYes
DatasheetDownload MSP430F147IPAG datasheet
Quote
Find where to buy
 
Specifications 
Package GroupLQFP,TQFP,VQFN
Timers - 32-bit0
Active Power (uA/MHz)280
Multiplier16x16
Frequency(MHz)8
Operating Temperature Range(C)-40 to 85
RatingCatalog
GPIO Pins(#)48
FeaturesWatchdog,Temp Sensor
Approx. Price (US$)4.08 | 1ku
Timers - 16-bit2
AESN/A
Min VCC1.8
Max VCC3.6
DMA0
ADCADC12 - 8ch
Wakeup Time (us)6
Special I/ON/A
BSLUART
Standby Power (LPM3-uA)1.6
Non-volatile Memory (KB)32
RAM(KB)1
SPI2
I2C0
CPUMSP430
UART2
Comparators(#)Yes
  Mecanical Data
Pin nbPackage typeInd stdJEDEC codePackage qtyCarrierDevice markWidth (mm)Length (mm)Thick (mm)Pitch (mm)
64PAGTQFPS-PQFP-G160JEDEC TRAY (10+1)M430F147 10101.5
Application notes
• MSP430 SMBus
This application report describes a software implementation of the system management bus (SMBus) for the MSP430 microcontroller. It includes all master protocols, an interrupt-driven slave, and master usage examples. SMBus is derived from the I2C and is co | Doc
• MSP430 Isolated FET Interface
This application report describes how to build an isolated FET interface for the MSP430 Flash Emulation Tool (FET). When developing and debugging line-powered MSP430applications such as motor control, electricity energy meters, power monitoring systems etc | Doc
• HDQ Protocol Implementation with MSP430 | Doc
• FSK Modulation and Demodulation With the Microcontroller MSP430
This application report describes a software program for performing V.23 FSK modem transceiver functions using an MSP430 microcontroller. It makes use of novel filter architecture to perform DSP functions on a processor with only shift and add capabilities | Doc
• MSP430 32-kHz Crystal Oscillators (Rev. D)
Selection of the right crystal, correct load circuit, and proper board layout are important for a stable crystal oscillator. This application report summarizes crystal oscillator function and explains the parameters to select the correct crystal for ultra- | Doc
• Powering the MSP430 from a High Voltage Input using the TPS62122 (Rev. C) | Doc
• Generation and Recognition of DTMF Signals With the Microcontroller MSP430
The first part of the Application Report describes the generation of DTMF signals using the Microcontroller MSP430. Following an explanation of the most important specifications which are involved, the theoretical and mathematical processes will be discuss | Doc
• General Oversampling of MSP ADCs for Higher Resolution (Rev. A)
Multiple MSP ultra-low-power microcontrollers offer analog-to-digital converters (ADCs) to convert physical quantities into digital numbers, a function that is widely used across numerous applications. There are times, however, when a customer design deman | Doc
• Advanced Debugging Using the Enhanced Emulation Module (EEM) With CCS v6 (Rev. F) | Doc
• Simple 1.5 V Boost Converter for MSP430
A simple, efficient, low-cost, boost converter to take 1.5 V from a single type-AA alkaline battery to the operating voltage required by the MSP430 family of ultralow-power microcontrollers is described. Expected battery life is up to 1000 hours. | Doc
• Efficient MSP430 Code Synthesis for an FIR Filter
Digital filtering can be easily accomplished on the MSP430 using efficient multiplication. The tool accompanying this document automatically converts FIR filter coefficients to MSP430 assembly code that can be used in any application. Horner’s method and | Doc
• Wave Digital Filtering Using the MSP430
Digital filtering is an integral part of many digital signal processing algorithms. Digital filters are characterized as either recursive [infinite impulse response (IIR)] or non-recursive [finite impulse response (FIR)] filters. IIR filters require a smal | Doc
• MSP Code Protection Features
MSP microcontrollers (MCUs) offer a number of features to help control code accessibility in the device, to add different layers of code access management and protection strategies. These include features that can lock or password protect the JTAG/SBW acce | Doc
• Economic Voltage Measurement With the MSP430 Family
This application report describes voltage and current measurement methods using the MSP430 universal timer/port module. The report explains the two measurement methods (charge and discharge) and shows how to measure voltage and current. The equations for t | Doc
• 1.8V – 5.5V Input, High-Efficiency DCDC Converter Reference Design for MSP430 (Rev. B)
This reference design is presented to help application designers and others who are trying to use the MSP430 in a system with an input voltage in the range of 1.8 V to 5.5 V, and who must increase the application run time by making use of the complete batt | Doc
• Design Considerations When Using the MSP430 Graphics Library
LCDs are a growing commodity in todays market with products as diverse as children's toys to medical devices. Modern LCDs, along with the graphics displayed on them, are growing in complexity. A graphics library can simplify and accelerate development whil | Doc
• Digital Fan Control With Tachometer Using MSP430
Digital Fan Control with Tachometer using MSP430 Application Report | Doc
• Spread-Spectrum Clock Source Using an MSP430
While spread-spectrum clocking has long since been used in processor and memory clock trees, there are many other clocked systems, such as power supplies or switch-mode amplifiers, that continue to use a single-frequency clock. This can, in turn, generate | Doc
• Using the TPS3619 with MSP430 Microcontrollers Can Reduce Sys Power Consumption (Rev. A)
The MSP430 series of microcontrollers are ideal in applications where battery life is critical. These microcontollers require only 0.1?A of current in low-power RAM retention mode; In this mode the microcontroller must have power to retain volatile memor | Doc
• Tiny DCDC Converter Reference Design (Rev. A)
This reference design is presented to help application designers and others who are trying to use the MSP430 in a system with an input voltage in the range of 3.6 V to 6 V with the primary design objective to minimize solution size as well as to maintain h | Doc
• AES128 – A C Implementation for Encryption and Decryption (Rev. A)
This application report describes the AES algorithm and the use of a suggested C implementation for AES encryption and decryption with MSP430.Note: This document may be subject to the export control policies of the local government. | Doc
• Interfacing TMS320C5000 DSP to MSP430 Mixed Signal Microcontroller (Rev. A)
The TMS320C5000™ family of digital signal processors (DSPs) features Host Port Interface Controllers (HPI) and Direct Memory Access Controllers (DMAC) for efficient data movement without any CPU involvement. The HPI enables the DSP to interface to host p | Doc
• MSP430 LFXT1 Oscillator Accuracy
This report details the factors that influence achievable accuracy of the low frequency oscillator, specifically for real-time clock (RTC) applications. The intent of this application report is to provide an understanding of MSP430-specific factors influen | Doc
• Interfacing the 3-V MSP430 to 5-V Circuits
The interfacing of the 3-V MSP430x1xx and MSP430x4xx microcontroller families to circuits with a supply of 5 V or higher is shown. Input, output and I/O interfaces are given and explained. Worse-case design equations are provided, where necessary. Some sim | Doc
• Programming a Flash-Based MSP430 Using the JTAG Interface (Rev. H)
This application report has been superseded by the document shown below. Information previously contained in this application report can be found by clicking on the following links.- MSP430 Programming Via the JTAG Interface User's Guide Download MSP430 P | Doc
• Mixing C and Assembler with the MSP430
This application note describes how C and assembler code can be used together within an MSP430 application. The combination of C and assembler benefits the designer by providing the power of a high-level language as well as the speed, efficiency, and low-l | Doc
• Efficient Multiplication and Division Using MSP430 | Doc
• ESD Diode Current Specification
This document explains the maximum ESD diode current specified for GPIO on MSP microcontrollers. Sometimes signals on specific pins exceed the supply of the MSP MCU. In such a case, the device can handle this overvoltage condition through the ESD diodes, b | Doc
• Implementing An Ultralow-Power Keypad Interface with MSP430
Often in applications with keypads, the condition can occur where a key can be held or stuck down, causing excess current consmption and reducing the battery life of a battery-operated product. This application report shows a solution. The keypad interfa | Doc
• MSP430 Embedded Application Binary Interface
This document is a specification for the ELF-based Embedded Application Binary Interface (EABI) for the MSP430 family of processors from Texas Instruments. The EABI defines the low-level interface between programs, program components, and the execution env | Doc
• Choosing an Ultra Low-Power MCU
This application report describes how to compare ultralow-power MCUs. It discusses the key differences between popular low-power MCUs and how to interpret features and specifications and apply them to application requirements. | Doc
• Interfacing the MSP430 and TLC549/1549 A/D Converters
This application report describes how to interface an MSP430 mixed-signal microcontroller with the TLC549 and TLV1549 3-volt A/D converters. This report is written for the MSP430x11x(1) family, but can be adapted to any MSP430 derivative. | Doc
• Fuzzy Logic Motor Control with MSP430x14x
This application report discusses the implementation of a fuzzy logic control algorithm using an MSP430F14x device. Fuzzy logic control algorithms can be used to solve problems that are difficult to address with traditional control techniques. As an exampl | Doc
• Boost DC/DC with Ultra-Low Shutdown Current (Rev. A)
This reference design is presented to help application designers and others who are trying to use the MSP430 in a system that requires a very low input voltage range while also maintaining high efficiency. Battery life is extended as well as a result of th | Doc
• Current Transformer Phase Shift Compensation and Calibration
This application report demonstrates a digital technique to compensate and calibrate the phase shift of a current (or voltage) transformer used in electric power of energy measurement. Traditional analog compensation is replaced by a digital finite impulse | Doc
• MSP430 Family Mixed-Signal Microcontroller Application Reports
MSP430 Metering Application Report | Doc
• Li-Ion Battery Charger solution using the MSP430 | Doc
• MSP430 Software Coding Techniques (Rev. A)
This application report covers software techniques and topics of interest to all MSP430 programmers. The first part of the document discusses the MSP430 standard interrupt-based code flow model, recommended for the vast majority of applications. The next p | Doc
• MSP430 Capacitive Single-Touch Sensor Design Guide
This application report discusses the design of RC-type capacitive single-touch sensors using the MSP430 microcontroller. The MSP430 has some unique features that make it suitable for interfacing with capacitive-touch sensors. The RC-type method does not n | Doc
• MSP430 Flash Memory Characteristics (Rev. A)
Flash memory is a widely used, reliable, and flexible nonvolatile memory to store software code and data in a microcontroller. Failing to handle the flash according to data-sheet specifications may result in unreliable operation of the application. This ap | Doc
• Understanding MSP430 Flash Data Retention
The MSP430 family of microcontrollers, as part of its broad portfolio, offers both read-only memory (ROM)-based and flash-based devices. Understanding the MSP430 flash is extremely important for efficient, robust, and reliable system design. Data retention | Doc
• CRC Implementation with MSP430
Cyclic Redundancy Code (CRC) is commonly used to determine the correctness of a data transmission or storage. This application note presents a solution to compute 16-bit and 32-bit CRCs on the ultra low-power TI MSP430 microcontroller for the bitwise algor | Doc
• Random Number Generation Using the MSP430
Many applications require the generation of random numbers. These random numbers are useful for applications such as communication protocols, cryptography, and device individualization.Generating random numbers often requires the use of expensive dedicated | Doc
Evaluation Kits
MSP-FET430U64: 64-pin Target Development Board and MSP-FET Programmer Bundle - MSP430F1x, MSP430F2x, MSP430F4x MCUs
MSP-TS430PM64: MSP-TS430PM64 - 64-pin Target Development Board for MSP430F1x, MSP430F2x and MSP430F4x MCUs

 

Features, Applications

Low Supply-Voltage Range, 3.6 V Ultralow-Power Consumption: Active Mode: at 1 MHz, 2.2V Standby Mode: A Off Mode (RAM Retention): 0.1 A Five Power-Saving Modes Wake-Up From Standby Mode in less than s 16-Bit RISC Architecture, 125-ns Instruction Cycle Time 12-Bit A/D Converter With Internal Reference, Sample-and-Hold and Autoscan Feature 16-Bit Timer_B With Seven Capture/Compare-With-Shadow Registers 16-Bit Timer_A With Three Capture/Compare Registers On-Chip Comparator Serial Onboard Programming, No External Programming Voltage Needed Programmable Code Protection by Security Fuse

Serial Communication Interface (USART), Functions as Asynchronous UART or Synchronous SPI Interface Two USARTs USART1) MSP430x14x(1) Devices One USART (USART0) MSP430x13x Devices Family Members Include: MSP430F133: 8KB+256B Flash Memory, 256B RAM MSP430F135: 16KB+256B Flash Memory, 512B RAM MSP430F1471: 32KB+256B Flash Memory, 1KB RAM MSP430F1481: 48KB+256B Flash Memory, 2KB RAM MSP430F1491: 60KB+256B Flash Memory, 2KB RAM Available in 64-Pin Quad Flat Pack (QFP) For Complete Module Descriptions, See the MSP430x1xx Family User's Guide, Literature Number SLAU049

The MSP430F14x1 devices are identical to the MSP430F14x devices with the exception that the ADC12 module is not implemented.

description

The Texas Instruments MSP430 family of ultralow-power microcontrollers consist of several devices featuring different sets of peripherals targeted for various applications. The architecture, combined with five low power modes is optimized to achieve extended battery life in portable measurement applications. The device features a powerful 16-bit RISC CPU, 16-bit registers, and constant generators that attribute to maximum code efficiency. The digitally controlled oscillator (DCO) allows wake-up from low-power modes to active mode in less than 6 s. The MSP430x13x and the MSP430x14x(1) series are microcontroller configurations with two built-in 16-bit timers, a fast 12-bit A/D converter (not implemented on the MSP430F14x1 devices), one or two universal serial synchronous/asynchronous communication interfaces (USART), and 48 I/O pins. Typical applications include sensor systems that capture analog signals, convert them to digital values, and process and transmit the data to a host system. The timers make the configurations ideal for industrial control applications such as ripple counters, digital motor control, EE-meters, hand-held meters, etc. The hardware multiplier enhances the performance and offers a broad code and hardware-compatible family solution.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.

AVAILABLE OPTIONS PACKAGED DEVICES TA PLASTIC 64-PIN QFP (PM) MSP430F149IPM MSP430F1491IPM PLASTIC 64-PIN QFP (PAG)


 

Related products with the same datasheet
MSP430F147IPM
MSP430F147IPMR
MSP430F147IPMRG4
MSP430F147IRTDR
MSP430F147IRTDT
MSP430F147IRTDT
MSP430F147IRTDT
Some Part number from the same manufacture Texas Instruments, Inc.
MSP430F147IPM ti MSP430F147, 16-Bit Ultra-low-power Microcontroller, 32 KB Flash, 1KB RAM, 12 Bit ADC, 2 Usarts, HW Multiplier
MSP430F148
MSP430F148 Ultra-low Power Microcontroller
MSP430F1481
MSP430F1481IPM ti MSP430F1481, 16-Bit Ultra-low-power Microcontroller, 48 KB Flash, 2KB RAM, 2 Usarts, HW Multiplier
MSP430F148IPAG ti MSP430F148, 16-Bit Ultra-low-power Microcontroller, 48 KB Flash, 2KB RAM, 12 Bit ADC, 2 Usarts, HW Multiplier
MSP430F149
MSP430F149 Ultra-low Power Microcontroller
MSP430F1491
MSP430F1491IPM ti MSP430F1491, 16-Bit Ultra-low-power Microcontroller, 60 KB Flash, 2KB RAM, 2 Usarts, HW Multiplier
MSP430F149IPAG ti MSP430F149, 16-Bit Ultra-low-power Microcontroller, 60 KB Flash, 2KB RAM, 12 Bit ADC, 2 Usarts, HW Multiplier
MSP430F155 Ultra-low Power Microcontroller
MSP430F155IPM ti MSP430F155, 16-bit Ultra-low-power MCU, 16kB Flash, 512B RAM, 12-Bit ADC, Dual 12-Bit DAC, Usart, I2C, Dma
MSP430F156 Ultra-low Power Microcontroller
MSP430F157
MSP430F1610
MSP430F1610IPM ti MSP430F1610, 16-bit Ultra-low-power MCU, 32kB Flash, 5124B RAM, 12-Bit ADC, Dual DAC, 2 Usart, I2C, HW Mult, Dma
MSP430F1611 Ultra-low Power Microcontroller
MSP430F1612
MSP430F167
MSP430F168

SN54AHCT16374WD : 16-bit Edge-triggered D-type Flip-flops With 3-state Outputs

SN54S30J : ti SN54S30, 8-Input Positive-nand Gates

SN74ABT543DWR : Registered Transceivers ti SN74ABT543, Octal Registered Transceivers With 3-State Outputs

TPS780300250DRVT : 150mA, LDO Reg, Ultralow-Pwr, Iq 500nA W/ Pin-Selectable, Dual-Level Output Volt The TPS780 family of low-dropout (LDO) regulators offer the benefits of ultralow power (IQ = 500nA), miniaturized packaging (22 SON-6), and selectable dual-level output voltage levels. An adjustable version is also av

BQ27505YZGT-J1 : System-Side Impedance Track Fuel Gauge The Texas Instruments bq27505 system-side Li-Ion battery fuel gauge is a microcontroller peripheral that provides fuel gauging for single-cell Li-Ion battery packs. The device requeires little system microcontroller firmware development. The bq27505 resides o

TLV70012DCKR : 200mA, Low IQ, Low Dropout Regulator For Portables The TLV700xx series of low-dropout (LDO) linear regulators are low quiescent current devices with excellent line and load transient performance. These LDOs are designed for power-sensitive applications. A precision bandgap and error amplifier provi

TLV1117-33CDRJRG4 : Adjustable AND Fixed Low-dropout Voltage Regulator

TLC3702QDRG4Q1 : Linear - Comparator Integrated Circuit (ics) General Purpose Tape & Reel (TR) 4 V ~ 16 V; IC DUAL LINCMOS V-COMP 8-SOIC Specifications: Type: General Purpose ; Output Type: CMOS, Push-Pull, TTL ; Voltage - Supply: 4 V ~ 16 V ; Number of Elements: 2 ; Package / Case: 8-SOIC (0.154", 3.90mm Width) ; Packaging: Tape & Reel (TR) ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant

TPS76628DG4 : Pmic - Voltage Regulator - Linear (ldo) Integrated Circuit (ics); IC LDO REG 2.8V 250MA 8-SOIC Specifications: Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant

THS4022IDG4 : Linear - Amplifier - Instrumentation, Op Amps, Buffer Amp Integrated Circuit (ics) Voltage Feedback Tube 7.8mA 2; IC OPAMP VFB 350MHZ DUAL 8SOIC Specifications: Packaging: Tube ; Amplifier Type: Voltage Feedback ; Number of Circuits: 2 ; Package / Case: 8-SOIC (0.154", 3.90mm Width) ; Slew Rate: 470 V/s ; Gain Bandwidth Product: - ; Current - Supply: 7.8mA ; Current - Output / Channel: 100mA ; Voltage - Supply, Single/Dual (): 9 V ~ 32 V,

CC1021RSS : Rf Transceiver Rf/if And Rfid; IC RF TXRX FOR NARROWBAND 32QFN Specifications: Frequency: 402MHz ~ 470MHz, 804MHz ~ 940MHz ; Data Rate - Maximum: 153.6kBaud ; Modulation or Protocol: FSK, GFSK, OOK ; Applications: AMR, ISM, RKE, SRD, TPMS ; Power - Output: -20dBm ~ 10dBm ; Sensitivity: -103dBm ; Voltage - Supply: 2.3 V ~ 3.6 V ; Current - Receiving: 19.9mA ; Cu

ISO7820LLDW : Digital Isolators High-Performance, 8000-VPK Reinforced Dual-Channel Digital Isolator 16-SOIC -55 to 125 Texas Instruments ISO782xLL Dual-Channel Digital Isolators are a high-performance, isolated dual-LVDS buffer with 8000VPK isolation voltage. This device provides high electromagnetic immunity and low emissions at low-power consumption while isolating the LVDS bus signal. Each isolation channel ha

Same catergory

HD6432353 : CISC->H8->Mask ROM. Series of Microcomputers Built Around The H8s/2000 Cpu.

HE84761 : with LCD Driver. ROM Type = Mask ;; Application = LCD Driver MCU ;; ROM = 256KB(Programmable 256KB) ;; RAM = 4KB ;; I/o = 16~36 ;; LCD = 4096~2560.

KMC9S12A128BCFU : HCS12 Family. 9S12A128 Device Guide. Original Release Date: 8 March, 2002 Revised: 17 April, 2002 Motorola reserves the right to make changes without further notice to any products herein to improve reliability, function or design. Motorola does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license.

LPC2210 : 16/32-bit Arm Microcontroller; With 10-bit ADC And External Memory Interfacethe LPC2210 is Based on a 16/32 Bit ARM7TDMI-STM Cpu With Real-time Emulation And Embedded Trace Support. For Critical Code Size Applications, The Alternative 16-bit Thumb Mode Reduces Code BY More Than 30pct With Minimal Performance Penalty. With Its 144 Pin Package, Low Power.

MN101C46F : ROM(×8-bit) = 96K ;; RAM(×8-bit) = 3K ;; I/O(Pins) = 35 ;; Package = SDIP042-P-0600C(Pb Free).

MN101C51F : ROM(×8-bit) = 96K ;; RAM(×8-bit) = 6K ;; I/O(Pins) = 70 ;; Package = LQFP080-P-1414A(Pb Free).

TMP47C1237N : CISC->TMP. CMOS 4-bit Microcontroller.

TMP87CH41 : CISC->TMP. CMOS 8- Bit Microcontroller.

TMP93PW46AF : TLCS-900L Series. ROM Size = Null ;; RAM Size = Null ;; Supply Voltage = Null ;; I/o Count = Null ;; Unique = OTP Version of 93CW46AF ;; Additional Information = More Info.

UPD78P322 : 16/8-bit Single-chip Microcontroller. The is a version provided by replacing the PD75322's internal mask ROM with one-time PROM or EPROM. Because the one-time PROM version is programmable only once by users, it is ideally suited for small-scale production of many different products, and rapid development and time-to-market of application sets. The EPROM version is reprogrammable, and suited.

W78L51-24 : 8-bit Microcontroller. The W78L51 microcontroller supplies a wider frequency and supply voltage range than most 8-bit microcontrollers on the market. It is compatible with the industry standard 80C51 microcontroller series. The W78L51 contains four 8-bit bidirectional parallel ports, one extra 4-bit bit-addressable I/O port (Port 4) and two additional external interrupts.

Z86C91 : ROM (KB)  = ROMless ;; RAM  = 236 ;; Speed  = 16 ;; I/O  = 32 ;; 8-bit Timers  = 2 ;; Comm Interfaces  = Uart ;; Other   = -- ;; Voltage  = 4.5-5.5V ;;.

ATmega324P : 32-Kbyte self-programming Flash Program Memory, 2-Kbyte SRAM, 1-KByte EEPROM, 8 Channel 10-bit A/D-converter. JTAG interface for on-chip-debug. Up to 20 MIPS throughput at 20 MHz. 1.8 - 5.5 Volt Operation..

SST89V516RD2 : The SST89E516RDx and SST89V516RDx are members of the FlashFlex family of 8-bit microcontroller products designed and manufactured with SSTs patented and proprietary SuperFlash CMOS semiconductor process technology. The split-gate cell design and thick-oxide tunneling injector offer significant cost and reliability benefits for SSTs customers. The devices.

 
0-C     D-L     M-R     S-Z