Details, datasheet, quote on part number: MSP430F155
PartMSP430F155
CategorySemiconductors => Microcontrollers (MCU) => MSP430 ultra-low-power MCUs => MSP430F1x
Part familyMSP430F155 16-bit Ultra-Low-Power MCU, 16kB Flash, 512B RAM, 12-Bit ADC, Dual 12-Bit DAC, USART, I2C, DMA
Description16-bit Ultra-Low-Power MCU, 16kB Flash, 512B RAM, 12-Bit ADC, Dual 12-Bit DAC, USART, I2C, DMA 64-LQFP -40 to 85
CompanyTexas Instruments, Inc.
StatusACTIVE
ROHSY
SampleYes
DatasheetDownload MSP430F155 datasheet
Cross ref.Similar parts: STM32F051C4, CY8C26443-24PVI, CY8C26443-24SI, CY8C26643-24PVI
Quote
Find where to buy
 
Specifications 
MultiplierN/A
SPI1
I2C1
Timers - 32-bit0
DMA3
Frequency(MHz)8
Operating Temperature Range(C)-40 to 85
RatingCatalog
UART1
GPIO Pins(#)48
Timers - 16-bit2
AESN/A
Min VCC1.8
Package GroupLQFP,VQFN
RAM(KB)0.5
Max VCC3.6
Approx. Price (US$)5.49 | 1ku
ADCADC12 - 8ch
FeaturesWatchdog,Temp Sensor,Brown Out Reset
Non-volatile Memory (KB)16
Wakeup Time (us)6
Special I/ON/A
BSLUART
Active Power (uA/MHz)330
Standby Power (LPM3-uA)1.1
CPUMSP430
Comparators(#)Yes
  Mecanical Data
Pin nbPackage typeInd stdJEDEC codePackage qtyCarrierDevice markWidth (mm)Length (mm)Thick (mm)Pitch (mm)
64PMLQFPS-PQFP-G160JEDEC TRAY (10+1)M430F155 10101.4.5
Application notes
• MSP430 SMBus
This application report describes a software implementation of the system management bus (SMBus) for the MSP430 microcontroller. It includes all master protocols, an interrupt-driven slave, and master usage examples. SMBus is derived from the I2C and is co | Doc
• MSP430 Isolated FET Interface
This application report describes how to build an isolated FET interface for the MSP430 Flash Emulation Tool (FET). When developing and debugging line-powered MSP430applications such as motor control, electricity energy meters, power monitoring systems etc | Doc
• HDQ Protocol Implementation with MSP430 | Doc
• FSK Modulation and Demodulation With the Microcontroller MSP430
This application report describes a software program for performing V.23 FSK modem transceiver functions using an MSP430 microcontroller. It makes use of novel filter architecture to perform DSP functions on a processor with only shift and add capabilities | Doc
• MSP430 32-kHz Crystal Oscillators (Rev. D)
Selection of the right crystal, correct load circuit, and proper board layout are important for a stable crystal oscillator. This application report summarizes crystal oscillator function and explains the parameters to select the correct crystal for ultra- | Doc
• Powering the MSP430 from a High Voltage Input using the TPS62122 (Rev. C) | Doc
• Generation and Recognition of DTMF Signals With the Microcontroller MSP430
The first part of the Application Report describes the generation of DTMF signals using the Microcontroller MSP430. Following an explanation of the most important specifications which are involved, the theoretical and mathematical processes will be discuss | Doc
• General Oversampling of MSP ADCs for Higher Resolution (Rev. A)
Multiple MSP ultra-low-power microcontrollers offer analog-to-digital converters (ADCs) to convert physical quantities into digital numbers, a function that is widely used across numerous applications. There are times, however, when a customer design deman | Doc
• Advanced Debugging Using the Enhanced Emulation Module (EEM) With CCS v6 (Rev. F) | Doc
• Simple 1.5 V Boost Converter for MSP430
A simple, efficient, low-cost, boost converter to take 1.5 V from a single type-AA alkaline battery to the operating voltage required by the MSP430 family of ultralow-power microcontrollers is described. Expected battery life is up to 1000 hours. | Doc
• Efficient MSP430 Code Synthesis for an FIR Filter
Digital filtering can be easily accomplished on the MSP430 using efficient multiplication. The tool accompanying this document automatically converts FIR filter coefficients to MSP430 assembly code that can be used in any application. Horner’s method and | Doc
• Wave Digital Filtering Using the MSP430
Digital filtering is an integral part of many digital signal processing algorithms. Digital filters are characterized as either recursive [infinite impulse response (IIR)] or non-recursive [finite impulse response (FIR)] filters. IIR filters require a smal | Doc
• MSP Code Protection Features
MSP microcontrollers (MCUs) offer a number of features to help control code accessibility in the device, to add different layers of code access management and protection strategies. These include features that can lock or password protect the JTAG/SBW acce | Doc
• Economic Voltage Measurement With the MSP430 Family
This application report describes voltage and current measurement methods using the MSP430 universal timer/port module. The report explains the two measurement methods (charge and discharge) and shows how to measure voltage and current. The equations for t | Doc
• 1.8V – 5.5V Input, High-Efficiency DCDC Converter Reference Design for MSP430 (Rev. B)
This reference design is presented to help application designers and others who are trying to use the MSP430 in a system with an input voltage in the range of 1.8 V to 5.5 V, and who must increase the application run time by making use of the complete batt | Doc
• Design Considerations When Using the MSP430 Graphics Library
LCDs are a growing commodity in todays market with products as diverse as children's toys to medical devices. Modern LCDs, along with the graphics displayed on them, are growing in complexity. A graphics library can simplify and accelerate development whil | Doc
• Digital Fan Control With Tachometer Using MSP430
Digital Fan Control with Tachometer using MSP430 Application Report | Doc
• Spread-Spectrum Clock Source Using an MSP430
While spread-spectrum clocking has long since been used in processor and memory clock trees, there are many other clocked systems, such as power supplies or switch-mode amplifiers, that continue to use a single-frequency clock. This can, in turn, generate | Doc
• Using the TPS3619 with MSP430 Microcontrollers Can Reduce Sys Power Consumption (Rev. A)
The MSP430 series of microcontrollers are ideal in applications where battery life is critical. These microcontollers require only 0.1?A of current in low-power RAM retention mode; In this mode the microcontroller must have power to retain volatile memor | Doc
• Tiny DCDC Converter Reference Design (Rev. A)
This reference design is presented to help application designers and others who are trying to use the MSP430 in a system with an input voltage in the range of 3.6 V to 6 V with the primary design objective to minimize solution size as well as to maintain h | Doc
• AES128 – A C Implementation for Encryption and Decryption (Rev. A)
This application report describes the AES algorithm and the use of a suggested C implementation for AES encryption and decryption with MSP430.Note: This document may be subject to the export control policies of the local government. | Doc
• Interfacing TMS320C5000 DSP to MSP430 Mixed Signal Microcontroller (Rev. A)
The TMS320C5000™ family of digital signal processors (DSPs) features Host Port Interface Controllers (HPI) and Direct Memory Access Controllers (DMAC) for efficient data movement without any CPU involvement. The HPI enables the DSP to interface to host p | Doc
• MSP430 LFXT1 Oscillator Accuracy
This report details the factors that influence achievable accuracy of the low frequency oscillator, specifically for real-time clock (RTC) applications. The intent of this application report is to provide an understanding of MSP430-specific factors influen | Doc
• Interfacing the 3-V MSP430 to 5-V Circuits
The interfacing of the 3-V MSP430x1xx and MSP430x4xx microcontroller families to circuits with a supply of 5 V or higher is shown. Input, output and I/O interfaces are given and explained. Worse-case design equations are provided, where necessary. Some sim | Doc
• Programming a Flash-Based MSP430 Using the JTAG Interface (Rev. H)
This application report has been superseded by the document shown below. Information previously contained in this application report can be found by clicking on the following links.- MSP430 Programming Via the JTAG Interface User's Guide Download MSP430 P | Doc
• Mixing C and Assembler with the MSP430
This application note describes how C and assembler code can be used together within an MSP430 application. The combination of C and assembler benefits the designer by providing the power of a high-level language as well as the speed, efficiency, and low-l | Doc
• Efficient Multiplication and Division Using MSP430 | Doc
• ESD Diode Current Specification
This document explains the maximum ESD diode current specified for GPIO on MSP microcontrollers. Sometimes signals on specific pins exceed the supply of the MSP MCU. In such a case, the device can handle this overvoltage condition through the ESD diodes, b | Doc
• Implementing An Ultralow-Power Keypad Interface with MSP430
Often in applications with keypads, the condition can occur where a key can be held or stuck down, causing excess current consmption and reducing the battery life of a battery-operated product. This application report shows a solution. The keypad interfa | Doc
• MSP430 Embedded Application Binary Interface
This document is a specification for the ELF-based Embedded Application Binary Interface (EABI) for the MSP430 family of processors from Texas Instruments. The EABI defines the low-level interface between programs, program components, and the execution env | Doc
• Choosing an Ultra Low-Power MCU
This application report describes how to compare ultralow-power MCUs. It discusses the key differences between popular low-power MCUs and how to interpret features and specifications and apply them to application requirements. | Doc
• Interfacing the MSP430 and TLC549/1549 A/D Converters
This application report describes how to interface an MSP430 mixed-signal microcontroller with the TLC549 and TLV1549 3-volt A/D converters. This report is written for the MSP430x11x(1) family, but can be adapted to any MSP430 derivative. | Doc
• Boost DC/DC with Ultra-Low Shutdown Current (Rev. A)
This reference design is presented to help application designers and others who are trying to use the MSP430 in a system that requires a very low input voltage range while also maintaining high efficiency. Battery life is extended as well as a result of th | Doc
• Current Transformer Phase Shift Compensation and Calibration
This application report demonstrates a digital technique to compensate and calibrate the phase shift of a current (or voltage) transformer used in electric power of energy measurement. Traditional analog compensation is replaced by a digital finite impulse | Doc
• MSP430 Family Mixed-Signal Microcontroller Application Reports
MSP430 Metering Application Report | Doc
• Li-Ion Battery Charger solution using the MSP430 | Doc
• MSP430 Software Coding Techniques (Rev. A)
This application report covers software techniques and topics of interest to all MSP430 programmers. The first part of the document discusses the MSP430 standard interrupt-based code flow model, recommended for the vast majority of applications. The next p | Doc
• MSP430 Capacitive Single-Touch Sensor Design Guide
This application report discusses the design of RC-type capacitive single-touch sensors using the MSP430 microcontroller. The MSP430 has some unique features that make it suitable for interfacing with capacitive-touch sensors. The RC-type method does not n | Doc
• MSP430 Flash Memory Characteristics (Rev. A)
Flash memory is a widely used, reliable, and flexible nonvolatile memory to store software code and data in a microcontroller. Failing to handle the flash according to data-sheet specifications may result in unreliable operation of the application. This ap | Doc
• Understanding MSP430 Flash Data Retention
The MSP430 family of microcontrollers, as part of its broad portfolio, offers both read-only memory (ROM)-based and flash-based devices. Understanding the MSP430 flash is extremely important for efficient, robust, and reliable system design. Data retention | Doc
• CRC Implementation with MSP430
Cyclic Redundancy Code (CRC) is commonly used to determine the correctness of a data transmission or storage. This application note presents a solution to compute 16-bit and 32-bit CRCs on the ultra low-power TI MSP430 microcontroller for the bitwise algor | Doc
• Random Number Generation Using the MSP430
Many applications require the generation of random numbers. These random numbers are useful for applications such as communication protocols, cryptography, and device individualization.Generating random numbers often requires the use of expensive dedicated | Doc
Evaluation Kits
MSP-FET430U64: 64-pin Target Development Board and MSP-FET Programmer Bundle - MSP430F1x, MSP430F2x, MSP430F4x MCUs
MSP-TS430PM64: MSP-TS430PM64 - 64-pin Target Development Board for MSP430F1x, MSP430F2x and MSP430F4x MCUs

 

Features, Applications

No External Programming Voltage Needed Programmable Code Protection by Security Fuse Family Members Include: MSP430F155: 16KB+256B Flash Memory 512B RAM MSP430F156: 24KB+256B Flash Memory 1KB RAM MSP430F157: 32KB+256B Flash Memory, 1KB RAM MSP430F167: 32KB+256B Flash Memory, 1KB RAM MSP430F168: 48KB+256B Flash Memory, 2KB RAM MSP430F169: 60KB+256B Flash Memory, 2KB RAM MSP430F1610: 32KB+256B Flash Memory 5KB RAM MSP430F1611: 48KB+256B Flash Memory 10KB RAM MSP430F1612: 55KB+256B Flash Memory 5KB RAM Available in 64-Pin Quad Flat Pack (QFP) For Complete Module Descriptions, See the MSP430x1xx Family User's Guide, Literature Number SLAU049

- Active Mode: at 1 MHz, V - Standby Mode: A - Off Mode (RAM Retention): 0.2 A Five Power-Saving Modes Wake-Up From Standby Mode in less than s 16-Bit RISC Architecture, 125-ns Instruction Cycle Time Three-Channel Internal DMA 12-Bit A/D Converter With Internal Reference, Sample-and-Hold and Autoscan Feature Dual 12-Bit D/A Converters With Synchronization 16-Bit Timer_A With Three Capture/Compare Registers 16-Bit Timer_B With Three or Seven Capture/Compare-With-Shadow Registers On-Chip Comparator Serial Communication Interface (USART0), Functions as Asynchronous UART or Synchronous SPI or I2CTM Interface Serial Communication Interface (USART1), Functions as Asynchronous UART or Synchronous SPI Interface Supply Voltage Supervisor/Monitor With Programmable Level Detection Brownout Detector Bootstrap Loader

description

The Texas Instruments MSP430 family of ultralow power microcontrollers consist of several devices featuring different sets of peripherals targeted for various applications. The architecture, combined with five low power modes is optimized to achieve extended battery life in portable measurement applications. The device features a powerful 16-bit RISC CPU, 16-bit registers, and constant generators that attribute to maximum code efficiency. The digitally controlled oscillator (DCO) allows wake-up from low-power modes to active mode in less than 6s. The MSP430x15x/16x/161x series are microcontroller configurations with two built-in 16-bit timers, a fast 12-bit A/D converter, dual 12-bit D/A converter, one or two universal serial synchronous/asynchronous communication interfaces (USART), I2C, DMA, and 48 I/O pins. In addition, the MSP430x161x series offers extended RAM addressing for memory-intensive applications and large C-stack requirements. Typical applications include sensor systems, industrial control applications, hand-held meters, etc.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.

AVAILABLE OPTIONS PACKAGED DEVICES TA PLASTIC 64-PIN QFP (PM) MSP430F1611IPM MSP430F1612IPM
AVCC DVSS AVSS P6.1/A1 P6.0/A0 RST/NMI TCK TMS TDI/TCLK TDO/TDI P5.6/ACLK P5.5/SMCLK
AVCC DVSS AVSS P6.1/A1 P6.0/A0 RST/NMI TCK TMS TDI/TCLK TDO/TDI P5.6/ACLK P5.5/SMCLK

 

Some Part number from the same manufacture Texas Instruments, Inc.
MSP430F155IPM ti MSP430F155, 16-bit Ultra-low-power MCU, 16kB Flash, 512B RAM, 12-Bit ADC, Dual 12-Bit DAC, Usart, I2C, Dma
MSP430F156 Ultra-low Power Microcontroller
MSP430F157
MSP430F1610
MSP430F1610IPM ti MSP430F1610, 16-bit Ultra-low-power MCU, 32kB Flash, 5124B RAM, 12-Bit ADC, Dual DAC, 2 Usart, I2C, HW Mult, Dma
MSP430F1611 Ultra-low Power Microcontroller
MSP430F1612
MSP430F167
MSP430F168
MSP430F169
MSP430F169IPM ti MSP430F169, 16-bit Ultra-low-power MCU, 60kB Flash, 2048B RAM, 12-Bit ADC, Dual DAC, 2 Usart, I2C, HW Mult, Dma
MSP430F412
MSP430F412 Ultra-low Power Microcontroller
MSP430F412IPM ti MSP430F412, 16-Bit Ultra-low-power Microcontroller, 4kB Flash, 256B RAM, Comparator, 96 Segment LCD
MSP430F413
MSP430F413 Ultra-low Power Microcontroller
MSP430F413IPM ti MSP430F413, 16-Bit Ultra-low-power Microcontroller, 8kB Flash, 256B RAM, Comparator, 96 Segment LCD
MSP430F415 Ultra-low Power Microcontroller
MSP430F417
MSP430F423
MSP430F425

5962-9550404QDA : Low Voltage Rail-to-rail Low Power Advanced LinCMOS(TM) Quad Operational Amplifier

74AC11873 : CMOS/BiCMOS->AC/ACT Family Dual 4-bit D-type Latch With 3-state Output

PT6405D : Plug-in Power Solutions->Non-Isolated->Single Posi ti PT6405, 3.3Vout 3A 5V-Input Adjustable Step-down Isr

SN74AS244A : Bus Oriented Circuits Octal Buffers And Line Drivers With 3-state Outputs

UA78L09CLPR : ti UA78L09, 9V, 100mA Fixed Positive Voltage Regulator

UC1610J : Schottky Diode Arrays ti UC1610, Dual Schottky Diode Bridge

TMP320R2812GHHQ : Tms320r2811, Tms320r2812 Digital Signal Processors

SN74LVCC4245APWRE4 : 32-bit BUS Transceiver WITH 3-state Outputs

SMJ320C6713GNZM20EP : Floating-point Digital Signal Processors

DAC7654YCTG4 : Data Acquisition - Digital To Analog Converter (dac) Integrated Circuit (ics) Tape & Reel (TR) Analog and Digital, Dual ; IC DAC 16BIT SER 64-LQFP Specifications: Data Interface: Serial, SPI ; Number of Bits: 16 ; Operating Temperature: -40C ~ 85C ; Package / Case: 64-LQFP ; Packaging: Tape & Reel (TR) ; Voltage Supply Source: Analog and Digital, Dual ; Settling Time: 12s ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant

SN74HC258DRE4 : Multiplexers ti SN74HC258, Quadruple 2-Line to 1-Line Data Selectors/multiplexers With 3-State Outputs

Same catergory

87C196CB : 16 MHZ Advanced 16-bit Chmos Microcontroller With Integrated CAN 2.0. to +125C Ambient High Performance CHMOS 16-Bit CPU to 56 Kbytes of On-Chip EPROM to 1.5 Kbyte of On-Chip Register RAM to 512 Bytes of Additional RAM (Code RAM) Register-Register Architecture 8 Channel/10-Bit A/D with Sample/Hold 38 Prioritized Interrupts Up to Seven 8-Bit (56) I/O Ports Full Duplex Serial I/O Port with Dedicated Baud Rate Generator.

8XC52 : CISC->8051/80C51 Family->8031/8051. Chmos Single-chip 8-bit Microcontroller.

ARM7TDMI : RISC->RISC. 16/32-bit Risc Microcontroller Core System. ARM High-performance 32-bit Instruction Set Thumb High-code-density 16-bit Instruction Set Very Low Power Consumption: Industry-leader in MIPS/Watt 4G Bytes Linear Address Space Von Neumann Load/Store Architecture: Single 32-bit Data Bus for Instructions and Data 3-Stage Pipeline Architecture: Fetch, Decode and Execute Stage 8-, 16-, and 32-bit.

KMP47C1660N : 4-bit Microcontrollers.

KMP47C443DM : 4-bit Microcontrollers.

LC66404A : 4-bit Microcomputer (4 Kbyte ROM-contained).

M80C51FB : Chmos Single-chip 8-bit Microcontroller. 3 5 MHz to 12 MHz VCC 3 5 MHz to 16 MHz VCC g 20% Three 16-Bit Timer Counters Programmable Clock Out Programmable Counter Array with High Speed Output Compare Capture Pulse Width Modulator Watchdog Timer capabilities Up Down Timer Counter 256 Bytes of On-Chip Data RAM Boolean Processor ONCE (On-Circuit Emulation) Mode Available in 40-pin CERDIP and 44-pin.

MN6750165 : Microprocessor.

PXAG49 : XA Family. XA-G49; Xa 16-bit Microcontroller Family 64K FLASH/2K RAM, Watchdog, 2 UARTs;; Package: SOT187-2 (PLCC44), SOT389-1 (LQFP44).

R2010C : High Performance 16bits MCU Integrated One 10/100M Mac Controller - 3.3V Operating Voltage.

SAB80C166 : CISC->C16x/C5xx. 16-bit CMOS Single-chip Microcontroller. High Performance 16-bit CPU with 4-Stage Pipeline 100 ns Instruction Cycle Time at 20 MHz CPU Clock 500 ns Multiplication 16 bit), 1 s Division / 16 bit) Enhanced Boolean Bit Manipulation Facilities Register-Based Design with Multiple Variable Register Banks Single-Cycle Context Switching Support to 256 KBytes Linear Address Space for Code and Data.

TMP47C454AF : CMOS 4-bit Microcontroller.

TMP47C662N : CMOS 4-bit Microcontroller.

TMP96C031 : CISC->TMP. CMOS 16-bit Microcontrollers. The TMP96C031 are high-speed advanced 16-bit microcontrollers developed for controlling medium to large-scale equipment. TMP96C031N comes a 64-pin shrink DIP; the a 64-pin flat package. (1) Original 16-bit CPU TLCS-90 instruction mnemonic upward compatible. 16M-byte linear address space General-purpose registers and register bank system 16-bit multiplication/division.

TMS370C010A : 8-bit Microcontroller. CMOS/ EEPROM/ EPROM Technologies on a Single Device Mask-ROM Devices for High-Volume Production One-Time-Programmable (OTP) EPROM Devices for Low-Volume Production Reprogrammable-EPROM Devices for Prototyping Purposes Internal System Memory Configurations On-Chip Program Memory Versions ROM: or 8K Bytes EPROM: 8K Bytes Data EEPROM: 256 Bytes.

Z86E30 : OTP (KB)  = 4 ;; RAM  = 237 ;; Speed  = 16 ;; I/O  = 24 ;; 8-bit Timers  = 2 ;; Comm Interfaces  = -- ;; Other   = Por, LV Protect ;; Voltage  = 3.5-5.5V ;;.

HT48R062 : HT48R062/HT48C062 -- Cost-Effective I/O Type 8-Bit MCU General The HT48R062/HT48C062 are 8-bit high performance, RISC architecture microcontroller devices specifically designed for cost-effective multiple I/O control product applications. The mask version HT48C062 is fully pin and functionally compatible with the OTP version HT48R062 devices. The advantages.

MCF52223DS : reduced instruction set computing (RISC) microprocessors. This document provides an overview of the 32-bit MCF52223 microcontroller, focusing on its highly integrated and diverse feature set. Freescale reserves the right to change or discontinue this product without notice. s and information herein are subject to change without notice. This 32-bit device.

MC9S08GT60A : HCS08 Microcontrollers The MC9S08GBxxA/GTxxA are members of the low-cost, high-performance HCS08 Family of 8-bit microcontroller units (MCUs). All MCUs in the family use the enhanced HCS08 core and are available with a variety of modules, memory sizes, memory types, and package types..

PIC12F1822 : PIC12F/LF1822/PIC16F/LF1823 8/14-Pin Flash MCUs W/ NanoWatt XLP Technology # Enhanced Mid-range Core with 49 Instruction, 16 Stack Levels # Flash Program Memory with self read/write capability # Internal 32MHz oscillator # Integrated Capacitive mTouch Sensing Module # Data Signal Modulator Module # MI2C, SPI, EUSART w/auto baud # ECCP (Enhanced/Capture.

 
0-C     D-L     M-R     S-Z