|
Details, datasheet, quote on part number:SN54ABT2245
| |
Datasheet text preview:
SN54ABT2245, SN74ABT2245 OCTAL TRANSCEIVERS AND LINE/MOS DRIVERS WITH 3-STATE OUTPUTS
SCBS234D SEPTEMBER 1992 REVISED MAY 1997
D D D D D D D
B-Port Outputs Have Equivalent 25- Series Resistors, So No External Resistors Are Required State-of-the-Art EPIC-BTM BiCMOS Design Significantly Reduces Power Dissipation Latch-Up Performance Exceeds 500 mA Per JEDEC Standard JESD-17 ESD Protection Exceeds 2000 V Per MIL-STD-833, Method 3015; Exceeds 200 V Using Machine Model (C = 200 pF, R = 0) Typical VOLP (Output Ground Bounce) < 1 V at VCC = 5 V, TA = 25°C High-Impedance State During Power Up and Power Down Package Options Include Plastic Small-Outline (DW), Shrink Small-Outline (DB), and Thin Shrink Small-Outline (PW) Packages, Ceramic Chip Carriers (FK), Plastic (N) and Ceramic (J) DIPs, and Ceramic Flat (W) Package
SN54ABT2245 . . . J OR W PACKAGE SN74ABT2245 . . . DB, DW, N, OR PW PACKAGE (TOP VIEW)
DIR A1 A2 A3 A4 A5 A6 A7 A8 GND
1 2 3 4 5 6 7 8 9 10
20 19 18 17 16 15 14 13 12 11
VCC OE B1 B2 B3 B4 B5 B6 B7 B8
SN54ABT2245 . . . FK PACKAGE (TOP VIEW)
A2 A1 DIR VCC A3 A4 A5 A6 A7
4 5 6 7 8
3 2 1 20 19 18 17 16 15 14 9 10 11 12 13
OE B1 B2 B3 B4 B5
description
These octal transceivers and line drivers are designed for asynchronous communication between data buses. The devices transmit data from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the direction-control (DIR) input. The output-enable (OE) input can be used to disable the device so the buses are effectively isolated.
The B-port outputs, which are designed to sink up to 12 mA, include equivalent 25- series resistors to reduce overshoot and undershoot. When VCC is between 0 and 2.1 V, the device is in the high-impedance state during power up or power down. However, to ensure the high-impedance state above 2.1 V, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking/current-sourcing capability of the driver. The SN54ABT2245 is characterized for operation over the full military temperature range of 55°C to 125°C. The SN74ABT2245 is characterized for operation from 40°C to 85°C.
FUNCTION TABLE INPUTS OE L L H DIR L H X OPERATION B data to A bus A data to B bus Isolation
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. EPIC-B is a trademark of Texas Instruments Incorporated.
PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.
Copyright © 1997, Texas Instruments Incorporated
POST OFFICE BOX 655303
· DALLAS, TEXAS 75265
A8 GND B8 B7 B6
1
SN54ABT2245, SN74ABT2245 OCTAL TRANSCEIVERS AND LINE/MOS DRIVERS WITH 3-STATE OUTPUTS
SCBS234D SEPTEMBER 1992 REVISED MAY 1997
logic symbol
OE DIR 19 1 G3 3 EN1 [BA] 3 EN2 [AB] 1 2 A2 A3 A4 A5 A6 A7 A8 3 4 5 6 7 8 9 17 16 15 14 13 12 11 B2 B3 B4 B5 B6 B7 B8 18 B1
A1
2
This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.
logic diagram (positive logic)
DIR 1 19
OE
A1
2
18
B1
To Seven Other Channels
2
POST OFFICE BOX 655303
· DALLAS, TEXAS 75265
SN54ABT2245, SN74ABT2245 OCTAL TRANSCEIVERS AND LINE/MOS DRIVERS WITH 3-STATE OUTPUTS
SCBS234D SEPTEMBER 1992 REVISED MAY 1997
schematic of A-port outputs
VCC
schematic of B-port outputs
VCC
Output
25 Output
GND All resistor values shown are nominal.
GND
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 V to 7 V Input voltage range, VI (except I/O ports) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 V to 7 V Voltage range applied to any output in the high or power-off state, VO . . . . . . . . . . . . . . . . . . . 0.5 V to 5.5 V Current into any output in the low state, IO: SN54ABT2245 (except B port) . . . . . . . . . . . . . . . . . . . . . . 96 mA SN74ABT2245 (except B port) . . . . . . . . . . . . . . . . . . . . . 128 mA B port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 mA Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA Package thermal impedance, JA (see Note 2): DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115°C/W DW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97°C/W N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67°C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65°C to 150°C
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 2. The package thermal impedance is calculated in accordance with EIA/JEDEC Std JESD51, except for through-hole packages, which use a trace length of zero.
POST OFFICE BOX 655303
· DALLAS, TEXAS 75265
3
|
|
