|
Details, datasheet, quote on part number:SN65C3223DW
| |
Datasheet text preview:
SN65C3223, SN75C3223 3 V TO 5.5 V MULTICHANNEL RS 232 COMPATIBLE LINE DRIVER/RECEIVER S
LLS538A - JUNE 2002 - REVISED MARCH 2004
D D D D D D D D
Operate With 3-V to 5.5-V VCC Supply Operate Up To 1 Mbit/s Low Standby Current . . . 1 µA Typical External Capacitors . . . 4 × 0.1 µF Accept 5-V Logic Input With 3.3-V Supply Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II RS-232 Bus-Pin ESD Protection Exceeds ±15 kV Using Human-Body Model (HBM) Applications - Battery-Powered Systems, PDAs, Notebooks, Laptops, Palmtop PCs, and Hand-Held Equipment
DB, DW, OR PW PACKAGE (TOP VIEW)
EN C1+ V+ C1- C2+ C2- V- DOUT2 RIN2 ROUT2
1 2 3 4 5 6 7 8 9 10
20 19 18 17 16 15 14 13 12 11
FORCEOFF VCC GND DOUT1 RIN1 ROUT1 FORCEON DIN1 DIN2 INVALID
description/ordering information
The SN65C3223 and SN75C3223 consist of two line drivers, two line receivers, and a dual charge-pump circuit with ±15-kV ESD protection pin to pin (serial-port connection pins, including GND). The devices provide the electrical interface between an asynchronous communication controller and the serial-port connector. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-V supply. The devices operate at data signaling rates up to 1 Mbit/s and a driver output slew rate of 24 V/µs to 150 V/µs Flexible control options for power management are available when the serial port is inactive. The auto-powerdown feature functions when FORCEON is low and FORCEOFF is high. During this mode of operation, if the device does not sense a valid RS-232 signal, the driver outputs are disabled. If FORCEOFF is set low and EN is high, both drivers and receivers are shut off, and the supply current is reduced to 1 µA. Disconnecting the serial port or turning off the peripheral drivers causes auto-powerdown to occur. Auto-powerdown can be disabled when FORCEON and FORCEOFF are high. With auto-powerdown enabled, the device is activated automatically when a valid signal is applied to any receiver input. The INVALID output is used to notify the user if an RS-232 signal is present at any receiver input. INVALID is high (valid data) if any receiver input voltage is greater than 2.7 V or less than -2.7 V or has been between -0.3 V and 0.3 V for less than 30 µs. INVALID is low (invalid data) if the receiver input voltage is between -0.3 V and 0.3 V for more than 30 µs. Refer to Figure 4 for receiver input levels. ORDERING INFORMATION
TA SOIC - DW 0°C to 70 C 70°C SSOP - DB TSSOP - PW SOIC - DW -40°C to 85 C 85°C SSOP - DB TSSOP - PW PACKAGE Tube of 25 Reel of 2000 Reel of 2000 Tube of 70 Reel of 2000 Tube of 25 Reel of 2000 Reel of 2000 Tube of 70 Reel of 2000 ORDERABLE PART NUMBER SN75C3223DW SN75C3223DWR SN75C3223DBR SN75C3223PW SN75C3223PWR SN65C3223DW SN65C3223DWR SN65C3223DBR SN65C3223PW SN65C3223PWR CB3223 65C3223 CB3223 CA3223 75C3223 CA3223 TOP-SIDE MARKING
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.
Copyright 2004, Texas Instruments Incorporated
POST OFFICE BOX 655303
· DALLAS, TEXAS 75265
1
SN65C3223, SN75C3223 3 V TO 5.5 V MULTICHANNEL RS 232 COMPATIBLE LINE DRIVER/RECEIVER S
LLS538A - JUNE 2002 - REVISED MARCH 2004
Function Tables
EACH DRIVER INPUTS DIN X L H L H L H FORCEON X H H L L L L FORCEOFF L H H H H H H VALID RIN RS-232 LEVEL X X X Yes Yes No No OUTPUT DOUT Z H L H L Z Z DRIVER STATUS Powered off Normal operation with auto-powerdown disabled Normal operation with auto-powerdown enabled Powered off by auto-powerdown feature
H = high level, L = low level, X = irrelevant, Z = high impedance EACH RECEIVER INPUTS RIN L H X Open EN L L H L VALID RIN RS-232 LEVEL X X X No OUTPUT ROUT H L Z H
H = high level, L = low level, X = irrelevant, Z = high impedance (off), Open = input disconnected or connected driver off
logic diagram (positive logic)
13 DIN1 17 DOUT1
12 DIN2 20 14 FORCEON 1 EN 15 ROUT1 Auto-powerdown
8 DOUT2
FORCEOFF
11 INVALID
16 RIN1
10 ROUT2
9 RIN2
2
POST OFFICE BOX 655303
· DALLAS, TEXAS 75265
SN65C3223, SN75C3223 3 V TO 5.5 V MULTICHANNEL RS 232 COMPATIBLE LINE DRIVER/RECEIVER S
LLS538A - JUNE 2002 - REVISED MARCH 2004
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage range, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to 6 V Positive output supply voltage range, V+ (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to 7 V Negative output supply voltage range, V- (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.3 V to -7 V Supply voltage difference, V+ - V- (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 V Input voltage range, VI: Driver, FORCEOFF, FORCEON, EN . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to 6 V Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -25 V to 25 V Output voltage range, VO: Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -13.2 V to 13.2 V Receiver, INVALID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to VCC + 0.3 V Package thermal impedance, JA (see Notes 2 and 3): DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . 70°C/W DW package . . . . . . . . . . . . . . . . . . . . . . . . . . 58°C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . 83°C/W Operating virtual junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65°C to 150°C
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltages are with respect to network GND. 2. Maximum power dissipation is a function of TJ(max), JA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) - TA)/JA. Operating at the absolute maximum TJ of 150°C can affect reliability. 3. The package thermal impedance is calculated in accordance with JESD 51-7.
recommended operating conditions (see Note 4 and Figure 6)
MIN VCC VIH VIL VI TA Supply voltage Driver and control high-level input voltage Driver and control low-level input voltage Driver and control input voltage Receiver input voltage Operating free-air temperature SN65C3223 SN65C3223 DIN, EN, FORCEOFF, FORCEON VCC = 3.3 V VCC = 5 V VCC = 3.3 V 3 4.5 2 2.4 0.8 0 -25 -40 0 5.5 25 85 70 V °C V V NOM 3.3 5 MAX 3.6 5.5 V UNIT
VCC = 5 V DIN, EN, FORCEOFF, FORCEON DIN, EN, FORCEOFF, FORCEON
NOTE 4: Test conditions are C1-C4 = 0.1 µF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 µF, C2-C4 = 0.33 µF at VCC = 5 V ± 0.5 V.
electrical characteristics over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Note 4 and Figure 6)
PARAMETER II Input leakage current EN, FORCEOFF, FORCEON Auto-powerdown disabled ICC Supply current Powered off Auto-powerdown enabled No load, FORCEOFF, FORCEON at VCC No load, FORCEOFF at GND No load, FORCEOFF at VCC, FORCEON at GND, All RIN are open or grounded TEST CONDITIONS MIN TYP ±0.01 0.3 1 1 MAX ±1 1 10 10 µA UNIT µA mA
All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C. NOTE 4: Test conditions are C1-C4 = 0.1 µF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 µF, C2-C4 = 0.33 µF at VCC = 5 V ± 0.5 V.
POST OFFICE BOX 655303
· DALLAS, TEXAS 75265
3
|
|
