|
Details, datasheet, quote on part number:SN74ABT16821DLR
| |
Datasheet text preview:
SN54ABT16821, SN74ABT16821 20-BIT BUS-INTERFACE FLIP-FLOPS WITH 3-STATE OUTPUTS
SCBS216B JUNE 1992 REVISED JANUARY 1997
D D D D D D D D
Members of the Texas Instruments Widebus TM Family State-of-the-Art EPIC-BTM BiCMOS Design Significantly Reduces Power Dissipation ESD Protection Exceeds 2000 V Per MIL-STD-883, Method 3015; Exceeds 200 V Using Machine Model (C = 200 pF, R = 0) Typical VOLP (Output Ground Bounce) < 1 V at VCC = 5 V, TA = 25°C Distributed VCC and GND Pin Configuration Minimizes High-Speed Switching Noise Flow-Through Architecture Optimizes PCB Layout High-Drive Outputs (32-mA IOH, 64-mA IOL ) Package Options Include Plastic Thin Shrink Small-Outline (DGG), 300-mil Shrink Small-Outline (DL) Packages and 380-mil Fine-Pitch Ceramic Flat (WD) Package Using 25-mil Center-to-Center Spacings
SN54ABT16821 . . . WD PACKAGE SN74ABT16821 . . . DGG OR DL PACKAGE (TOP VIEW)
description
These 20-bit flip-flops feature 3-state outputs designed specifically for driving highly capacitive or relatively low-impedance loads. They are particularly suitable for implementing wider buffer registers, I/O ports, bidirectional bus drivers with parity, and working registers. The 'ABT16821 can be used as two 10-bit flip-flops or one 20-bit flip-flop. The 20 flip-flops are edge-triggered D-type flip-flops. On the positive transition of the clock (CLK) input, the device provides true data at the Q outputs.
1OE 1Q1 1Q2 GND 1Q3 1Q4 VCC 1Q5 1Q6 1Q7 GND 1Q8 1Q9 1Q10 2Q1 2Q2 2Q3 GND 2Q4 2Q5 2Q6 VCC 2Q7 2Q8 GND 2Q9 2Q10 2OE
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29
1CLK 1D1 1D2 GND 1D3 1D4 VCC 1D5 1D6 1D7 GND 1D8 1D9 1D10 2D1 2D2 2D3 GND 2D4 2D5 2D6 VCC 2D7 2D8 GND 2D9 2D10 2CLK
A buffered output-enable (OE) input can be used to place the ten outputs in either a normal logic state (high or low logic level) or a high-impedance state. In the high-impedance state, the outputs neither load nor drive the bus lines significantly. The high-impedance state and increased drive provide the capability to drive bus lines without need for interface or pullup components. OE does not affect the internal operation of the flip-flops. Old data can be retained or new data can be entered while the outputs are in the high-impedance state. To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. The SN54ABT16821 is characterized for operation over the full military temperature range of 55°C to 125°C. The SN74ABT16821 is characterized for operation from 40°C to 85°C.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Widebus and EPIC-B are trademarks of Texas Instruments Incorporated.
UNLESS OTHERWISE NOTED this document contains PRODUCTION DATA information current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303
Copyright © 1997, Texas Instruments Incorporated
· DALLAS, TEXAS 75265
1
SN54ABT16821, SN74ABT16821 20-BIT BUS-INTERFACE FLIP-FLOPS WITH 3-STATE OUTPUTS
SCBS216B JUNE 1992 REVISED JANUARY 1997
FUNCTION TABLE (each flip-flop) INPUTS OE L L L H CLK L X D H L X X OUTPUT Q H L Q0 Z
logic symbol
1OE 1CLK 2OE 2CLK 1 56 28 29 C3 55 54 52 51 49 48 47 45 44 43 42 41 40 38 37 36 34 33 31 30 3D 4 1D 2 2 3 5 6 8 9 10 12 13 14 15 16 17 19 20 21 23 24 26 27 1Q1 1Q2 1Q3 1Q4 1Q5 1Q6 1Q7 1Q8 1Q9 1Q10 2Q1 2Q2 2Q3 2Q4 2Q5 2Q6 2Q7 2Q8 2Q9 2Q10 EN2 C1 EN4
1D1 1D2 1D3 1D4 1D5 1D6 1D7 1D8 1D9 1D10 2D1 2D2 2D3 2D4 2D5 2D6 2D7 2D8 2D9 2D10
This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.
2
POST OFFICE BOX 655303
· DALLAS, TEXAS 75265
SN54ABT16821, SN74ABT16821 20-BIT BUS-INTERFACE FLIP-FLOPS WITH 3-STATE OUTPUTS
SCBS216B JUNE 1992 REVISED JANUARY 1997
logic diagram (positive logic)
1OE 1
1CLK
56
One of Ten Channels 1D1 55
C1 1D
2
1Q1
To Nine Other Channels 28
2OE
2CLK
29
One of Ten Channels 42 2D1
C1 1D
15
2Q1
To Nine Other Channels
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 V to 7 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 V to 7 V Voltage range applied to any output in the high or power-off state, VO . . . . . . . . . . . . . . . . . . . 0.5 V to 5.5 V Current into any output in the low state, IO: SN54ABT16821 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 mA SN74ABT16821 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 mA Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA Package thermal impedance, JA (see Note 2): DGG package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81°C/W DL package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65°C to 150°C
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 2. The package thermal impedance is calculated in accordance with EIA/JEDEC Std JESD51.
POST OFFICE BOX 655303
· DALLAS, TEXAS 75265
3
|
|
