|
|
Part: SN74ABT16827DL
Category:
Logic
-> Buffers/Drivers
-> Non-Inverting Buffers and Drivers
Description: ti SN74ABT16827, 20-Bit Buffers/drivers With 3-State Outputs
Company: Texas Instruments, Inc.
Datasheet: Download SN74ABT16827DL datasheet File size : 214 kB
Request For quote: Find where to buy SN74ABT16827DL
Datasheet text preview:
SN54ABT16827, SN74ABT16827 20-BIT BUFFERS/DRIVERS WITH 3-STATE OUTPUTS
SCBS220C JUNE 1992 REVISED MAY 1997
D D D D D D D D D
Members of the Texas Instruments Widebus TM Family State-of-the-Art EPIC-BTM BiCMOS Design Significantly Reduces Power Dissipation Latch-Up Performance Exceeds 500 mA Per JEDEC Standard JESD-17 Typical VOLP (Output Ground Bounce) < 1 V at VCC = 5 V, TA = 25°C High-Impedance State During Power Up and Power Down Distributed VCC and GND Pin Configuration Minimizes High-Speed Switching Noise Flow-Through Architecture Optimizes PCB Layout High-Drive Outputs (32-mA IOH, 64-mA IOL) Package Options Include Plastic 300-mil Shrink Small-Outline (DL) Package and 380-mil Fine-Pitch Ceramic Flat (WD) Package Using 25-mil Center-to-Center Spacings
SN54ABT16827 . . . WD PACKAGE SN74ABT16827 . . . DL PACKAGE (TOP VIEW)
description
The 'ABT16827 are noninverting 20-bit buffers composed of two 10-bit sections with separate output-enable signals. For either 10-bit buffer section, the two output-enable (1OE1 and 1OE2 or 2OE1 and 2OE2) inputs must both be low for the corresponding Y outputs to be active. If either output-enable input is high, the outputs of that 10-bit buffer section are in the high-impedance state.
1OE1 1Y1 1Y2 GND 1Y3 1Y4 VCC 1Y5 1Y6 1Y7 GND 1Y8 1Y9 1Y10 2Y1 2Y2 2Y3 GND 2Y4 2Y5 2Y6 VCC 2Y7 2Y8 GND 2Y9 2Y10 2OE1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29
1OE2 1A1 1A2 GND 1A3 1A4 VCC 1A5 1A6 1A7 GND 1A8 1A9 1A10 2A1 2A2 2A3 GND 2A4 2A5 2A6 VCC 2A7 2A8 GND 2A9 2A10 2OE2
When VCC is between 0 and 2.1 V, the device is in the high-impedance state during power up or power down. However, to ensure the high-impedance state above 2.1 V, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. The SN54ABT16827 is characterized for operation over the full military temperature range of 55°C to 125°C. The SN74ABT16827 is characterized for operation from 40°C to 85°C.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Widebus and EPIC-B are trademarks of Texas Instruments Incorporated.
UNLESS OTHERWISE NOTED this document contains PRODUCTION DATA information current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303
Copyright © 1997, Texas Instruments Incorporated
· DALLAS, TEXAS 75265
1
SN54ABT16827, SN74ABT16827 20-BIT BUFFERS/DRIVERS WITH 3-STATE OUTPUTS
SCBS220C JUNE 1992 REVISED MAY 1997
FUNCTION TABLE (each 10-bit section) INPUTS OE1 L L H X OE2 L L X H A L H X X OUTPUT Y L H Z Z
logic symbol
1OE1 1OE2 2OE1 2OE2 1A1 1A2 1A3 1A4 1A5 1A6 1A7 1A8 1A9 1A10 2A1 2A2 2A3 2A4 2A5 2A6 2A7 2A8 2A9 2A10 1 56 28 29 55 54 52 51 49 48 47 45 44 43 42 41 40 38 37 36 34 33 31 30 1 2 & EN2 2 3 5 6 8 9 10 12 13 14 15 16 17 19 20 21 23 24 26 27 & EN1
1
1
1Y1 1Y2 1Y3 1Y4 1Y5 1Y6 1Y7 1Y8 1Y9 1Y10 2Y1 2Y2 2Y3 2Y4 2Y5 2Y6 2Y7 2Y8 2Y9 2Y10
This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.
2
POST OFFICE BOX 655303
· DALLAS, TEXAS 75265
SN54ABT16827, SN74ABT16827 20-BIT BUFFERS/DRIVERS WITH 3-STATE OUTPUTS
SCBS220C JUNE 1992 REVISED MAY 1997
logic diagram (positive logic)
1 1OE1 1OE2 56 2OE1 2OE2 28 29
1A1
55
2
1Y1
2A1
42
15
2Y1
To Nine Other Channels
To Nine Other Channels
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 V to 7 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 V to 7 V Voltage range applied to any output in the high or power-off state, VO . . . . . . . . . . . . . . . . . . . 0.5 V to 5.5 V Current into any output in the low state, IO: SN54ABT16827 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 mA SN74ABT16827 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 mA Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA Package thermal impedance, JA (see Note 2): DL package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65°C to 150°C
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 2. The package thermal impedance is calculated in accordance with EIA/JEDEC Std JESD51.
recommended operating conditions (see Note 3)
SN54ABT16827 MIN VCC VIH VIL VI IOH IOL t/v t/VCC Supply voltage High-level input voltage Low-level input voltage Input voltage High-level output current Low-level output current Input transition rise or fall rate transition rise or fall rate Power-up ramp rate Control pins Data pins 200 55 125 0 4.5 2 0.8 VCC 24 48 4 10 200 40 85 0 MAX 5.5 SN74ABT16827 MIN 4.5 2 0.8 VCC 32 64 4 10 MAX 5.5 UNIT V V V V mA mA ns/V µs/V °C
TA Operating free-air temperature NOTE 3: Unused inputs must be held high or low to prevent them from floating.
PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice.
POST OFFICE BOX 655303
· DALLAS, TEXAS 75265
3
Others parts begin by sn
SN-1 SN-2 SN-3 SN-4 SN-5 SN-6 SN-7 SN-8 SN-9 SN-10 SN-11 SN-12 SN-13 SN-14 SN-15 SN-16 SN-17 SN-18 SN-19 SN-20 SN-21 SN-22 SN-23 SN-24 SN-25 SN-26 SN-27 SN-28 SN-29 SN-30 SN-31 SN-32 SN-33 SN-34 SN-35 SN-36 SN-37 SN-38 SN-39 SN-40 SN-41 SN-42 SN-43 SN-44 SN-45 SN-46 SN-47 SN-48 SN-49 SN-50 SN-51 SN-52 SN-53 SN-54 SN-55 SN-56 SN-57 SN-58 SN-59 SN-60 SN-61 SN-62 SN-63 SN-64 SN-65 SN-66 SN-67 SN-68 SN-69 SN-70 SN-71 SN-72 SN-73 SN-74 SN-75 SN-76 SN-77 SN-78 SN-79 SN-80 SN-81 SN-82 SN-83 SN-84 SN-85 SN-86 SN-87 SN-88 SN-89 SN-90 SN-91 SN-92 SN-93 SN-94 SN-95 SN-96 SN-97 SN-98 SN-99 SN-100 SN-101 SN-102 SN-103 SN-104 SN-105 SN-106 SN-107 SN-108 SN-109 SN-110 SN-111 SN-112 SN-113 SN-114 SN-115 SN-116 SN-117 SN-118 SN-119 SN-120 SN-121
|
|
|
