|
|
Part: TS5V330DR
Category:
RF & Microwaves
-> Switches
-> SPDT Switches
Description: Quad SPDT Wide Bandwidth Video Switch With Low On-state Resistance<<<>>>the ti TS5V330 Video Switch is a 4-bit 1-of-2 Multiplexer/demultiplexer With a Single Switch-enable (EN) Input. When en is Low, The Switch is Enabled And The D Port is Connected to The S Port. When en is High, The Switch is Disabled And The High-impedance State Exists Between The D And S Ports. The Select (IN) Input Controls The Data Path of The Multiplexer/demultiplexer.
Company: Texas Instruments, Inc.
Datasheet: Download TS5V330DR datasheet File size : 329 kB
Request For quote: Find where to buy TS5V330DR
Datasheet text preview:
TS5V330 QUAD SPDT WIDE BANDWIDTH VIDEO SWITCH WITH LOW ON STATE RESISTANCE
SCDS164A MAY 2004 - REVISED MAY 2004
D Low Differential Gain and Phase D D D D D D D D D D D
(DG = 0.64%, DP = 0.1 Degrees Typ) Wide Bandwidth (BW = 300 MHz Min) Low Crosstalk (XTALK = -63 dB Typ) Low Power Consumption (ICC = 3 µA Max) Bidirectional Data Flow, With Near-Zero Propagation Delay Low ON-State Resistance (ron = 3 Typ) VCC Operating Range From 4.5 V to 5.5 V Ioff Supports Partial-Power-Down Mode Operation Data and Control Inputs Provide Undershoot Clamp Diode Control Inputs Can Be Driven by TTL or 5-V/3.3-V CMOS Outputs Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II ESD Performance Tested Per JESD 22 - 2000-V Human-Body Model (A114-B, Class II) - 1000-V Charged-Device Model (C101) Suitable for Both RGB and Composite-Video Switching
D, DBQ, OR PW PACKAGE (TOP VIEW)
IN S1A S2A DA S1B S2B DB GND
1 2 3 4 5 6 7 8
16 15 14 13 12 11 10 9
VCC EN S1D S2D DD S1C S2C DC
RGY PACKAGE (TOP VIEW)
IN
1
16 15 EN 14 S2D 13 S2D 12 DD 11 S1C 10 S2C
S1A S2A DA S1B S2B DB
2 3 4 5 6 7 8 9
description/ordering information
The TI TS5V330 video switch is a 4-bit 1-of-2 multiplexer/demultiplexer with a single switch-enable (EN) input. When EN is low, the switch is enabled and the D port is connected to the S port. When EN is high, the switch is disabled and the high-impedance state exists between the D and S ports. The select (IN) input controls the data path of the multiplexer/demultiplexer. ORDERING INFORMATION
TA QFN - RGY SOIC - D -40°C to 85°C SSOP (QSOP) - DBQ TSSOP - PW PACKAGE Tape and reel Tube Tape and reel Tape and reel Tube Tape and reel ORDERABLE PART NUMBER TS5V330RGYR TS5V330D TS5V330DR TS5V330DBQR TS5V330PW TS5V330PWR TE330 TS5V330 TE330 TOP-SIDE MARKING TE330
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.
Copyright 2004, Texas Instruments Incorporated
POST OFFICE BOX 655303
· DALLAS, TEXAS 75265
GND
D
DC
VCC
1
SCDS164A MAY 2004 - REVISED MAY 2004
TS5V330 QUAD SPDT WIDE BANDWIDTH VIDEO SWITCH WITH LOW ON STATE RESISTANCE
description/ordering information (continued)
Low differential gain and phase make this switch ideal for composite and RGB video applications. This device has wide bandwidth and low crosstalk, making it suitable for high-frequency applications as well. This device is fully specified for partial-power-down applications using Ioff. The Ioff feature ensures that damaging current will not backflow through the device when it is powered down. This switch maintains isolation during power off. To ensure the high-impedance state during power up or power down, EN should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
FUNCTION TABLE INPUTS EN L L H IN L H X INPUT/OUTPUT D S1 S2 Z PIN DESCRIPTIONS PIN NAME S1, S2 D IN EN DESCRIPTION Analog video I/Os Analog video I/Os Select input Switch-enable input FUNCTION D port = S1 port D port = S2 port Disconnect
2
POST OFFICE BOX 655303
· DALLAS, TEXAS 75265
TS5V330 QUAD SPDT WIDE BANDWIDTH VIDEO SWITCH WITH LOW ON STATE RESISTANCE
SCDS164A MAY 2004 - REVISED MAY 2004
PARAMETER DEFINITIONS PARAMETER ron IOZ IOS VIN VEN CIN COFF CO N VIH VIL Vhys VIK VI VO IIH IIL II IO Ioff tON tOFF BW XTALK OIRR DG DESCRIPTION Resistance between the D and S ports, with the switch in the ON state Output leakage current measured at the D and S ports, with the switch in the OFF state Short-circuit current measured at the I/O pins Voltage at the IN pin Voltage at the EN pin Capacitance at the control (EN, IN) inputs Capacitance at the analog I/O port when the switch is OFF Capacitance at the analog I/O port when the switch is ON Minimum input voltage for logic high for the control (EN, IN) inputs Minimum input voltage for logic low for the control (EN, IN) inputs Hysteresis voltage at the control (EN, IN) inputs I/O and control (EN, IN) inputs diode clamp voltage Voltage applied to the D or S pins when D or S is the switch input Voltage applied to the D or S pins when D or S is the switch output Input high leakage current of the control (EN, IN) inputs Input low leakage current of the control (EN, IN) inputs Current into the D or S pins when D or S is the switch input Current into the D or S pins when D or S is the switch output Output leakage current measured at the D or S ports, with VCC = 0 Propagation delay measured between 50% of the digital input to 90% of the analog output when switch is turned ON Propagation delay measured between 50% of the digital input to 90% of the analog output when switch is turned OFF Frequency response of the switch in the ON state measured at -3 dB Unwanted signal coupled from channel to channel. Measured in -dB. XTALK = 20 log VO/VI. This is a nonadjacent crosstalk. Off isolation is the resistance (measured in -dB) between the input and output with the switch OFF. Magnitude variation between analog input and output pins when the switch is ON and the dc offset of composite-video signal varies at the analog input pin. In the NTSC standard, the frequency of the video signal is 3.58 MHz, and dc offset is from 0 to 0.714 V. Phase variation between analog input and output pins when the switch is ON and the dc offset of composite-video signal varies at the analog input pin. In the NTSC standard, the frequency of the video signal is 3.58 MHz, and dc offset is from 0 to 0.714 V. Static power-supply current Variation of ICC for a change in frequency in the control (EN, IN) inputs This is the increase in supply current for each control input that is at the specified voltage level, rather than VCC or GND.
DP ICC ICCD ICC
POST OFFICE BOX 655303
· DALLAS, TEXAS 75265
3
Others parts begin by ts
TS-1 TS-2 TS-3 TS-4 TS-5 TS-6 TS-7 TS-8 TS-9 TS-10 TS-11 TS-12 TS-13 TS-14 TS-15 TS-16 TS-17 TS-18 TS-19 TS-20 TS-21 TS-22 TS-23 TS-24 TS-25 TS-26 TS-27 TS-28 TS-29 TS-30 TS-31 TS-32 TS-33 TS-34 TS-35 TS-36 TS-37 TS-38 TS-39 TS-40 TS-41 TS-42 TS-43 TS-44 TS-45 TS-46
|
|
|
