Details, datasheet, quote on part number: UCC3800D
PartUCC3800D
CategorySemiconductors => Power Management => Offline and Isolated DC/DC Controllers and Converters => PWM and Resonant Controller
Part familyUCC3800 Low-Power BiCMOS Current-Mode PWM
TitleCurrent Mode
DescriptionLow-Power BiCMOS Current-Mode PWM 8-SOIC 0 to 70
CompanyTexas Instruments, Inc.
StatusACTIVE
ROHSY
SampleYes
DatasheetDownload UCC3800D datasheet
Cross ref.Similar parts: UCC2800D, UCC2800D, UCC3800DTR, LM3478, LM5001, LM5002, TL2842, TL2842B, TL2843
Quote
Find where to buy
 
Specifications 
Operating Temperature Range(C)0 to 70
Duty Cycle(Max)(%)100
Frequency(Max)(kHz)1000
RatingCatalog
UVLO Thresholds On/Off(V)7.2/6.9
TopologyBoost,Buck,Flyback,Forward
Package GroupPDIP,SOIC,TSSOP
Approx. Price (US$)1.10 | 1ku
FeaturesError Amplifier,Leading Edge Blanking,Multi-topology,Soft Start
Vin(Min)(V)7.2
Control MethodCurrent
Gate Drive(Typ)(A)1
Vin(Max)(V)400
  Mecanical Data
Pin nbPackage typeInd stdJEDEC codePackage qtyCarrierDevice markWidth (mm)Length (mm)Thick (mm)Pitch (mm)
8DSOICR-PDSO-G75TUBEUCC3800 3.914.91.581.27
Application notes
• U-133A UCC3800/1/2/3/4/5 BiCMOS Current Mode Control IC's
The UCC3800 IC has several innovative features for general purpose current-mode controlled applications: high speed circuitry, undervoltage lockout, an op-amp type error amplifier, fast overcurrrent protection, a precision reference and a high-current tote | Doc
• UCC38C42 Family of High-Speed BiCMOS Current-Mode PWM Controllers
Since their introduction in the mid 1980?s, the bipolar UC3842 family of Pulse width modulation (PWM)controllers has grown to become the most widely-used control strategy in the power supply industry. [1] The reasons for success are quite clear, the device | Doc
• Dual Output Boost Converter
The boost converter is modified to provide bipolar 12-V outputs from 5-V supply. Using the UCC3803 to control the basic boost converter building block, the -12-V outputs are generated using a coupled inductor and a flying capacitor. Output voltage regulati | Doc
• DN-42A Design Considerations for Transitioning from UC3842 to the New UCC3802
The UCC3802 offers numerous advantages that allow the power supply design engineer to meet requirements for lower power for battery-operated equipment, higher switching frequencies for reduced magnetics size, higher levels of circuit integration for improv | Doc
• DN-46 Highly Efficient Low Power DC to DC Inverter Converts +5V Input to -3V Out
This design note describes a flyback inverter application using the UCC3805. The application performs three functions: control, switching, and output rectification. A circuit schematic and a list of materials are included. | Doc
• DN-56A, Single Switch Flyback Circuit Converts + 5 V to +/- 12 V for RS-232/422
A bipolar 12V supply from a single +5V input can be developed using a number of conventional approaches. A boost converter is the most logical for the +12V output; however, it cannot be used in some interface-circuit applications. One significant drawback | Doc
• DN-65 Considerations in Powering BiCMOS ICs
Bipolar linear integrated circuits have been with us for years in the form of PWM and PFC controllers, supervisory circuits, and other circuits. Since these devices have traditionally used relatively high-voltage (35V) bipolar processes, powering was not a | Doc
• DN-48 Versatile Low Power SEPIC Converter Accepts Wide Input Voltage Range
This design note describes an output converter for battery-powered and automotive applications. It uses a UCC3803 BiCMOS current-mode controller to provide a 5V output at full load of 100mA from an input of 2.5-13.5V after an initial startup at 5V. The UC3 | Doc
• Understanding Buck-Boost Power Stages in Switchmode Power Supplies (Rev. A) | Doc
• DN-62 Switching Power Supply Topology Voltage Mode vs. Current Mode
This design note explains the differences between voltage-mode and current-mode switching power supply topologies. It includes a circuit diagram for each mode and suggests criteria for choosing which mode to use. | Doc
• DN-54 Innovative Buck Regulator Uses High Side N-Channel Switch Without Complex
This application note shows how the innovative UCC3803 BiCMOS PWM controller provides very high efficiency without complex gate drives by using a high-side N-channel switch. It converts +5 VDC to +3.3 VDC (or others) and draws only 40 microamps in standby | Doc
• DN-43 Simple Techniques to Generate a Negative Voltage Bias Supply
A low-power negative supply voltage can be developed from a positive input supply using some very common PWM control ICs. Typical applications include generating a -5V to -12V supply for analog function ICs (OP amps), RS-232 communication circuits, and MOS | Doc
• Differences Between the UCC3813 and the UCC3800 PWM Families
This application report discusses the parametric differences between the UCC3813 and UCC3800 PWM families of integrated circuits available from Texas Instruments. | Doc
Spice Model
UCCx813-0, UCCx800 Families PSpice Transient Model (Rev. B) - ZIP (07/06/2010)
UCCx800 TINA-TI Transient Spice Model - ZIP (07/28/2011)
UCCx800 & UCCx813-0 Unencrypted PSpice Transient Model - ZIP (02/18/2016)

 

Features, Applications

FEATURES

100A Typical Starting Supply Current 500A Typical Operating Supply Current Operation to 1MHz Internal Soft Start Internal Fault Soft Start Internal Leading-Edge Blanking of the Current Sense Signal 1 Amp Totem-Pole Output 70ns Typical Response from Current-Sense to Gate Drive Output 1.5% Tolerance Voltage Reference Same Pinout as UC3842 and UC3842A

DESCRIPTION

The UCC1800/1/2/3/4/5 family of high-speed, low-power integrated circuits contain all of the control and drive components required for off-line and DC-to-DC fixed frequency current-mode switching power supplies with minimal parts count. These devices have the same pin configuration as the UC1842/3/4/5 family, and also offer the added features of internal full-cycle soft start and internal leading-edge blanking of the current-sense input. The UCC1800/1/2/3/4/5 family offers a variety of package options, temperature range options, choice of maximum duty cycle, and choice of critical voltage levels. Lower reference parts such as the UCC1803 and UCC1805 fit best into battery operated systems, while the higher reference and the higher UVLO hysteresis of the UCC1802 and UCC1804 make these ideal choices for use in off-line power supplies. The UCC180x series is specified for operation from C, o the UCC280x series is specified for operation from +85 C, and o the UCC380x series is specified for operation from +70 C.

VCC Voltage (Note 2). 12.0V VCC Current (Note 2). 30.0mA OUT Current. 1.0A OUT Energy (Capacitive Load). 20.0J Analog Inputs (FB, CS). to 6.3V Power Dissipation or J Package). 1.0W Power Dissipation +25C (D Package). 0.65W Storage Temperature Range. to +150C Lead Temperature (Soldering, 10 Seconds). +300C Note 1: Values beyond which damage may occur. All voltages are with respect to GND. All currents are positive into the specified terminal. Consult Unitrode databook for information regarding thermal specifications and limitations of packages. Note 2: In normal operation VCC is powered through a current limiting resistor. Absolute maximum of 12V applies when VCC is driven from a low impedance source such that ICC does not exceed 30mA (which includes gate drive current requirement).

ELECTRICAL CHARACTERISTICS Unless otherwise stated, these specifications apply for TA +125C for TA +85C for TA +70C for UCC380x; VCC=10V (Note 3); RT=100k from REF to RC; CT=330pF from RC to GND; 0.1 F capacitor from VCC to GND; 0.1 F capacitor from VREF to GND. TA=TJ.

PARAMETER TEST CONDITIONS MIN Reference Section Output Voltage Load Regulation Line Regulation VCC=10V to Clamp VCC=10V to Clamp (IVCC=25mA) Total Variation Output Noise Voltage Long Term Stability Output Short Circuit UCCx800/1/2/4 (Note 7) UCCx803/5 (Note 10kHz, TJ=+25C (Note TA=+125C, 1000 Hours (Note mV mV/V V

UCC2800/1/2/3/4/5 UCC3800/1/2/3/4/5 ELECTRICAL CHARACTERISTICS Unless otherwise stated, these specifications apply for TA +125C for TA +85C for TA +70C for UCC380x; VCC=10V (Note 3); RT=100k from REF to RC; CT=330pF from RC to GND; 0.1 F capacitor from VCC to GND; 0.1 F capacitor from VREF to GND. TA=TJ.


 

Related products with the same datasheet
UCC3800DTR
UCC3800N
UCC3800PW
UCC3800PWTR
Some Part number from the same manufacture Texas Instruments, Inc.
UCC3800DTR ti UCC3800, Low-power Bicmos Current-mode PWM
UCC3801 Low-power Bicmos Current-mode PWM
UCC3801D ti UCC3801, Low-power Bicmos Current-mode PWM
UCC3802 Low-power Bicmos Current-mode PWM
UCC3802D ti UCC3802, Low-power Bicmos Current-mode PWM
UCC3803 Low-power Bicmos Current-mode PWM
UCC3803D ti UCC3803, Low-power Bicmos Current-mode PWM
UCC3804 Low-power Bicmos Current-mode PWM
UCC3804D ti UCC3804, Low-power Bicmos Current-mode PWM
UCC3805 Low-power Bicmos Current-mode PWM
UCC38050 Transition Mode PFC Controller
UCC38050D ti UCC38050, Transition Mode PFC Controller
UCC38050DR Transition Mode PFC Controller
UCC38050DR ti UCC38050, Transition Mode PFC Controller
UCC38050P Transition Mode PFC Controller
UCC38050P ti UCC38050, Transition Mode PFC Controller
UCC38051 PFC Controller For Low to Medium Power Applications Requiring Compliance With Iec 1000-3-2
UCC38051D ti UCC38051, PFC Controller For Low to Medium Power Applications Requiring Compliance With Iec 1000-3-2
UCC38051DR PFC Controller For Low to Medium Power Applications Requiring Compliance With Iec 1000-3-2
UCC38051DR ti UCC38051, PFC Controller For Low to Medium Power Applications Requiring Compliance With Iec 1000-3-2
UCC38051P PFC Controller For Low to Medium Power Applications Requiring Compliance With Iec 1000-3-2
Same catergory

CS8371ET7 : 8V/1A, 5V/250mA Dual Regulator With Independent Output Enables And NoCap™ , Package: TO-220, Pins=7.

KA78L12A : 3-Terminal 0.1A Positive Voltage Regulator. Maximum Output Current of 100mA Output Voltage 15V, 18V and 24V Thermal Overload Protection Short Circuit Current Limiting Output Voltage Offered in 5% Tolerance The KA78LXXA/KA78L05AA series of fixed voltage monolithic integrated circuit voltage regulators are suitable for application that required supply current to 100mA. Parameter Input Voltage.

KBPC1006GW : 10a Glass Passivated Bridge Rectifier.

LGR4301-2 : 1030 Watt Ac-dc Converters. Input voltage ranges or 2 outputs V DC I/O electric strength test voltage Class II equipment (double insulation) Short circuit protection Compact, low cost solution Input voltage Input frequency continuous range Efficiency Output voltage switching noise Line and load regulation Uo1 Line and load regulation Uo2 Minimum load Hold-up time 230 V AC, Io nom Ui nom,.

LM368-5.0 : > 5V. Precision Voltage Reference. The is a precision monolithic temperature-compensated voltage reference The LM368 makes use of thin-film technology enhanced by the discrete laser trimming of resistors to achieve excellent Temperature coefficient (Tempco) of VOUT (as low 5ppm C) along with tight initial tolerance (as low 0 02%) The trim scheme is such that individual resistors are cut open.

LT1376HV : 1.5a, 500khz Step-down Switching Regulators. Constant 500kHz Switching Frequency Easily Synchronizable Uses All Surface Mount Components Inductor Size Reduced to 5H Saturating Switch Design: 0.4 Effective Supply Current: 2.5mA Shutdown Current: 20A Cycle-by-Cycle Current Limiting is current mode for fast transient response and good loop stability. Both fixed output voltage and adjustable parts.

LX8584A-00 : 7 a Low Dropout Positive Regulators. The LX8584/84A/84B series ICs are low dropout three-terminal positive regulators with a nominal 7A output current. This product family is ideally suited for Pentium Processor and Power PCTM applications requiring fast transient response. The LX8584A is guaranteed to have at 7A and the at 7A dropout voltage, making them ideal to provide well regulated.

MAX1693 : Usb Current-limited Switches With Fault Blanking. The MAX1693/(MAX1693H)/MAX1694 are current-limited, 60m switches with built-in fault blanking. Their accurate preset current limit to 1.0A makes them ideally suited for USB applications. Their low quiescent supply current (14A) and shutdown current (1A) conserve battery power in portable applications. The MAX1693/(MAX1693H)/MAX1694 operate with inputs.

NE56610-25GW : Reset Circuits. Product data Supersedes data of 2001 Apr 24 File under Integrated Circuits, Standard Analog 2001 Jun 19 The NE56610/11/12-XX series is a family of devices designed to generate a reset signal for a variety of microprocessor and logic systems. Accurate reset signals are generated during momentary power interruptions or when ever power supply voltages.

PT4581 : . Input Voltage Range: 60V 1500 VDC Isolation On/Off Control Vo Adjust Differential Remote Sense Current Limit Short-Circuit Protection Over-T emperature Shutdown Undervoltage Lockout Space-Saving Package Solderable Copper Case UL1950 Recognized CSA 22.2 950 Certified EN60950 Approved VDE Licensed 5 x106 Hrs MTBF Meets FCC Class A Radiated Limits The PT4580.

RT9163 : Single Output. Iout(mA) = 500 ;; IGND1( GA) = 4.5mA ;; Output Voltage(V) = 3.3, 3.5, 5.0 ;; Vin (Min) = ;; Vin (Max) = 15 ;; Accuracy(%) = 2 ;; / 2 = Bipolar, Low Dropout ;; Packages = SOT-89, SOT-223, TO-252, TO-92 ;;.

TEA1102 : TEA1102; TEA1102T; TEA1102TS; Fast Charge Ics For Nicd, Nimh, Sla And LiIon;; Package: SOT146-1 (DIP20), SOT163 (SO20), SOT339-1 (SSOP20).

UC2573 : Buck Pulse Width Modulator Stepdown Voltage Regulator. Buck Pulse Width Modulator Stepdown Voltage Regulator Simple Single Inductor Buck PWM Stepdown Voltage Regulation Drives External PMOS Switch Contains UVLO Circuit Includes Pulse-by-Pulse Current Limit Low 50A Sleep Mode Current The is a Buck pulse width modulator which steps down and regulates a positive input voltage. The chip is optimized for use in a single.

UC3825 : Current Mode PWM Controllers. High Speed PWM Controller.

LT3009 : 3A IQ, 20mA Low Dropout Linear Regulator The LT3009 is a micropower, low dropout voltage (LDO) linear regulator. The device supplies 20mA output current with a dropout voltage of 280mV. No-load quiescent current is 3A. Ground pin current remains at less than 5% of output current as load increases. In shutdown, quiescent current is less than 1A. The LT3009.

SC416 : Dual Synchronous Buck Controller with Tracking Start-up/Shutdown The SC416 is a versatile, constant on-time, pseudo-fixed-frequency, dual synchronous buck PWM controller intended for notebook computers and other battery operated portable devices. The SC416 contains all the needed to provide cost-effective control of two independent switchmode power.

LT3590 : 48V Buck Mode LED Driver in SC70 and 2mm x 2mm DFN The LT3590 is a fixed frequency buck mode converter specifically designed to drive up to 10 LEDs in series from a 48V DC source. Series connection of the LEDs provides identical LED currents of up to 50mA, resulting in uniform brightness and eliminating the need for ballast resistors. A fixed frequency,.

LM3445 : Triac Dimmable Offline LED Driver From The PowerWise Family The LM3445 is an adaptive constant off-time AC/DC buck (step-down) constant current controller designed to be compatible with triac dimmers. The LM3445 provides a constant current for illuminating high power LEDs and includes a triac dim decoder. The dim decoder allows wide range LED dimming.

NSI45025A : 45 V, 20 MA 15%, Constant Current Regulator & LED Driver, SOD-123 The solid state series of linear constant current regulators (CCRs) are Simple, Economical and Robust (SER) devices designed to provide a cost effective solution for regulating current in LEDs. The SER series regulators are based on patent-pending Self-Biased Transistor (SBT) technology.

 
0-C     D-L     M-R     S-Z