Details, datasheet, quote on part number: UCC3802D
PartUCC3802D
CategorySemiconductors => Power Management => Offline and Isolated DC/DC Controllers and Converters => PWM and Resonant Controller
Part familyUCC3802 Low-Power BiCMOS Current-Mode PWM
TitleCurrent Mode
DescriptionLow-Power BiCMOS Current-Mode PWM 8-SOIC 0 to 70
CompanyTexas Instruments, Inc.
StatusACTIVE
ROHSY
SampleYes
DatasheetDownload UCC3802D datasheet
Cross ref.Similar parts: UCC2802DTR, UCC2802D, UCC3802DTR, UCC3802PW, UCC3802PWTR, UCC3803, LM3478, LM5001, LM5002
Quote
Find where to buy
 
Specifications 
Operating Temperature Range(C)0 to 70
UVLO Thresholds On/Off(V)12.5/8.3
Duty Cycle(Max)(%)100
Frequency(Max)(kHz)1000
RatingCatalog
Vin(Min)(V)12.5
TopologyBoost,Buck,Flyback,Forward
Package GroupPDIP,SOIC,TSSOP
Approx. Price (US$)1.10 | 1ku
FeaturesError Amplifier,Leading Edge Blanking,Multi-topology,Soft Start
Control MethodCurrent
Gate Drive(Typ)(A)1
Vin(Max)(V)400
  Mecanical Data
Pin nbPackage typeInd stdJEDEC codePackage qtyCarrierDevice markWidth (mm)Length (mm)Thick (mm)Pitch (mm)
8DSOICR-PDSO-G75TUBEUCC3802 3.914.91.581.27
Application notes
• Conditioning a Switch-mode Power Supply Current Signal Using TI Op Amps
The switch-mode power supply primary current is often sensed using a power resistor. Using an op amp to amplify the current-sense signal can reduce cost and improve noise performance and efficiency. This report reviews the advantages of using an op amp cir | Doc
• U-133A UCC3800/1/2/3/4/5 BiCMOS Current Mode Control IC's
The UCC3800 IC has several innovative features for general purpose current-mode controlled applications: high speed circuitry, undervoltage lockout, an op-amp type error amplifier, fast overcurrrent protection, a precision reference and a high-current tote | Doc
• DN-89 Comparing the UC3842, UCC3802, and UCC3809 Primary Side PWM Controllers
Despite the fact that the UC3842 and the UCC3802 PWM Controllers are pin-for-pin compatible, they are not drop-in replacements for each other. Designed as the next generation '42, the UCC3809 also has differences that prevent a simple drop-in substitute. T | Doc
• U-111, Practical Considerations in Current Mode Power Supplies
This application note explains the numerous PWM functions and ways to maximize their usefulness. It covers practical circuit design considerations, such as slope compensation, gate drive circuitry, external control functions, synchronization, and paralleli | Doc
• UCC38C42 Family of High-Speed BiCMOS Current-Mode PWM Controllers
Since their introduction in the mid 1980?s, the bipolar UC3842 family of Pulse width modulation (PWM)controllers has grown to become the most widely-used control strategy in the power supply industry. [1] The reasons for success are quite clear, the device | Doc
• Dual Output Boost Converter
The boost converter is modified to provide bipolar 12-V outputs from 5-V supply. Using the UCC3803 to control the basic boost converter building block, the -12-V outputs are generated using a coupled inductor and a flying capacitor. Output voltage regulati | Doc
• DN-42A Design Considerations for Transitioning from UC3842 to the New UCC3802
The UCC3802 offers numerous advantages that allow the power supply design engineer to meet requirements for lower power for battery-operated equipment, higher switching frequencies for reduced magnetics size, higher levels of circuit integration for improv | Doc
• DN-46 Highly Efficient Low Power DC to DC Inverter Converts +5V Input to -3V Out
This design note describes a flyback inverter application using the UCC3805. The application performs three functions: control, switching, and output rectification. A circuit schematic and a list of materials are included. | Doc
• DN-56A, Single Switch Flyback Circuit Converts + 5 V to +/- 12 V for RS-232/422
A bipolar 12V supply from a single +5V input can be developed using a number of conventional approaches. A boost converter is the most logical for the +12V output; however, it cannot be used in some interface-circuit applications. One significant drawback | Doc
• DN-65 Considerations in Powering BiCMOS ICs
Bipolar linear integrated circuits have been with us for years in the form of PWM and PFC controllers, supervisory circuits, and other circuits. Since these devices have traditionally used relatively high-voltage (35V) bipolar processes, powering was not a | Doc
• DN-48 Versatile Low Power SEPIC Converter Accepts Wide Input Voltage Range
This design note describes an output converter for battery-powered and automotive applications. It uses a UCC3803 BiCMOS current-mode controller to provide a 5V output at full load of 100mA from an input of 2.5-13.5V after an initial startup at 5V. The UC3 | Doc
• Understanding Buck-Boost Power Stages in Switchmode Power Supplies (Rev. A) | Doc
• DN-54 Innovative Buck Regulator Uses High Side N-Channel Switch Without Complex
This application note shows how the innovative UCC3803 BiCMOS PWM controller provides very high efficiency without complex gate drives by using a high-side N-channel switch. It converts +5 VDC to +3.3 VDC (or others) and draws only 40 microamps in standby | Doc
• DN-43 Simple Techniques to Generate a Negative Voltage Bias Supply
A low-power negative supply voltage can be developed from a positive input supply using some very common PWM control ICs. Typical applications include generating a -5V to -12V supply for analog function ICs (OP amps), RS-232 communication circuits, and MOS | Doc
• Differences Between the UCC3813 and the UCC3800 PWM Families
This application report discusses the parametric differences between the UCC3813 and UCC3800 PWM families of integrated circuits available from Texas Instruments. | Doc
Spice Model
UCCx813-2, UCCx802 Families PSpice Transient Model (Rev. B) - ZIP (07/06/2010)
UCCx802 & UCCx813-2 Unencrypted PSpice Transient Model - ZIP (02/18/2016)
UCCX802 & UCCX813-2 TINA-TI Transient Spice Model - ZIP (10/11/2011)

 

Features, Applications

FEATURES

100A Typical Starting Supply Current 500A Typical Operating Supply Current Operation to 1MHz Internal Soft Start Internal Fault Soft Start Internal Leading-Edge Blanking of the Current Sense Signal 1 Amp Totem-Pole Output 70ns Typical Response from Current-Sense to Gate Drive Output 1.5% Tolerance Voltage Reference Same Pinout as UC3842 and UC3842A

DESCRIPTION

The UCC1800/1/2/3/4/5 family of high-speed, low-power integrated circuits contain all of the control and drive components required for off-line and DC-to-DC fixed frequency current-mode switching power supplies with minimal parts count. These devices have the same pin configuration as the UC1842/3/4/5 family, and also offer the added features of internal full-cycle soft start and internal leading-edge blanking of the current-sense input. The UCC1800/1/2/3/4/5 family offers a variety of package options, temperature range options, choice of maximum duty cycle, and choice of critical voltage levels. Lower reference parts such as the UCC1803 and UCC1805 fit best into battery operated systems, while the higher reference and the higher UVLO hysteresis of the UCC1802 and UCC1804 make these ideal choices for use in off-line power supplies. The UCC180x series is specified for operation from C, o the UCC280x series is specified for operation from +85 C, and o the UCC380x series is specified for operation from +70 C.

VCC Voltage (Note 2). 12.0V VCC Current (Note 2). 30.0mA OUT Current. 1.0A OUT Energy (Capacitive Load). 20.0J Analog Inputs (FB, CS). to 6.3V Power Dissipation or J Package). 1.0W Power Dissipation +25C (D Package). 0.65W Storage Temperature Range. to +150C Lead Temperature (Soldering, 10 Seconds). +300C Note 1: Values beyond which damage may occur. All voltages are with respect to GND. All currents are positive into the specified terminal. Consult Unitrode databook for information regarding thermal specifications and limitations of packages. Note 2: In normal operation VCC is powered through a current limiting resistor. Absolute maximum of 12V applies when VCC is driven from a low impedance source such that ICC does not exceed 30mA (which includes gate drive current requirement).

ELECTRICAL CHARACTERISTICS Unless otherwise stated, these specifications apply for TA +125C for TA +85C for TA +70C for UCC380x; VCC=10V (Note 3); RT=100k from REF to RC; CT=330pF from RC to GND; 0.1 F capacitor from VCC to GND; 0.1 F capacitor from VREF to GND. TA=TJ.

PARAMETER TEST CONDITIONS MIN Reference Section Output Voltage Load Regulation Line Regulation VCC=10V to Clamp VCC=10V to Clamp (IVCC=25mA) Total Variation Output Noise Voltage Long Term Stability Output Short Circuit UCCx800/1/2/4 (Note 7) UCCx803/5 (Note 10kHz, TJ=+25C (Note TA=+125C, 1000 Hours (Note mV mV/V V

UCC2800/1/2/3/4/5 UCC3800/1/2/3/4/5 ELECTRICAL CHARACTERISTICS Unless otherwise stated, these specifications apply for TA +125C for TA +85C for TA +70C for UCC380x; VCC=10V (Note 3); RT=100k from REF to RC; CT=330pF from RC to GND; 0.1 F capacitor from VCC to GND; 0.1 F capacitor from VREF to GND. TA=TJ.


 

Related products with the same datasheet
UCC3802DTR
UCC3802N
UCC3802PW
UCC3802PWTR
Some Part number from the same manufacture Texas Instruments, Inc.
UCC3802DTR ti UCC3802, Low-power Bicmos Current-mode PWM
UCC3803 Low-power Bicmos Current-mode PWM
UCC3803D ti UCC3803, Low-power Bicmos Current-mode PWM
UCC3804 Low-power Bicmos Current-mode PWM
UCC3804D ti UCC3804, Low-power Bicmos Current-mode PWM
UCC3805 Low-power Bicmos Current-mode PWM
UCC38050 Transition Mode PFC Controller
UCC38050D ti UCC38050, Transition Mode PFC Controller
UCC38050DR Transition Mode PFC Controller
UCC38050DR ti UCC38050, Transition Mode PFC Controller
UCC38050P Transition Mode PFC Controller
UCC38050P ti UCC38050, Transition Mode PFC Controller
UCC38051 PFC Controller For Low to Medium Power Applications Requiring Compliance With Iec 1000-3-2
UCC38051D ti UCC38051, PFC Controller For Low to Medium Power Applications Requiring Compliance With Iec 1000-3-2
UCC38051DR PFC Controller For Low to Medium Power Applications Requiring Compliance With Iec 1000-3-2
UCC38051DR ti UCC38051, PFC Controller For Low to Medium Power Applications Requiring Compliance With Iec 1000-3-2
UCC38051P PFC Controller For Low to Medium Power Applications Requiring Compliance With Iec 1000-3-2
UCC38051P ti UCC38051, PFC Controller For Low to Medium Power Applications Requiring Compliance With Iec 1000-3-2
UCC3805D ti UCC3805, Low-power Bicmos Current-mode PWM
UCC3806 Low Power, Dual Output, Current Mode PWM Controller
UCC3806DW ti UCC3806, Low Power, Dual Output, Current Mode PWM Controller
Same catergory

CBRHDSeries : High Density Surface Mount Ohms Amp Dual in Line Bridge Rectifier. CBRHD SERIES HIGH DENSITY AMP DUAL IN LINE BRIDGE RECTIFIER Truly efficient use of board space, requires only 42mm2 of board space vs. 120mm2 of board space for industry standard 1.0 Amp surface mount bridge rectifier. 50% higher density (amps/mm2) than the industry standard 1.0 Amp surface mount bridge rectifier. HD DIP CASE : The CENTRAL SEMICONDUCTOR.

GP2001-7R : 120195 Watt DC-DC Converters. Input voltage to 4 isolated outputs 4242V DC I/O electric strength test voltage Extremely slim case (4 TE), fully enclosed Extremely low inrush current, hot swappable Operating ambient temperature range 4071C with convection cooling Output 1 Output 2 Output 3 Output 4 Uo nom Po nom Po max Uo nom Po nom Po max Uo nom Po nom Po max Uo nom Po nom Po max [V DC] [W] [V DC] [W] [V DC] [W] [V DC] [W] Type.

HA17815V : 3-terminal Fixed Voltage Regulators. HA17800V series is positive output 1 A three-terminal regulator IC. Which are as follows. It is designed to suit to the power supply of various equipments and to stabilize the multi switching regulator voltage, and to supply power to some kind of control devices. High ripple rejection ratio up to high frequency (f 20 kHz): 60 dB(in the case of HA17805V/VP/VPJ).

ISL6842 : Improved Industry Standard Single Ended Current Mode PWM Controller. Improved Industry Standard Single Ended Current Mode PWM Controller The ISL6844, ISL6845 family of adjustable frequency, low power, pulse width modulating (PWM) current mode controllers is designed for a wide range of power conversion applications including boost, flyback, and isolated output configurations. Peak current mode control effectively handles.

MAX636XC/D : Preset/adjustable Output CMOS Inverting Switching Regulators.

MIC39150/1 : . The MIC39150 and MIC39151 are 1.5A low-dropout linear voltage regulators that provide a low voltage, high current output with a minimum of external components. Utilizing Micrel's proprietary Super eta PNPTM pass element, the MIC39150/1 offers extremely low dropout (typically at 1.5A) and low ground current (typically at 1.5A). The MIC39150/1 is ideal.

PQ15RW08 : Variable Output, Low Power Loss Voltage Regulator.

PT4504A : Plug-in Power Solutions->Isolated->Single Output. ti PT4504, 15V 20W 24V-Input ISOlated DC-DC Converter.

PT6715A : Plug-in Power Solutions->Non-Isolated->Single Posi. ti PT6715, 3.3Vout 13 Amp 5V-Input Adjustable Isr, cu Case.

TA78M15F : 0.5a Three Terminal Positive Voltage Regulators.

TK65020 : Step-up Voltage Converter. Guaranteed 0.9 V Operation Very Low Quiescent Current Internal Bandgap Reference High Efficiency MOS Switching Low Output Ripple Laser-Trimmed Output Voltage Laser-Trimmed Oscillator Undervoltage Lockout Regulation by Pulse Burst Modulation (PBM) Battery Powered Systems Cellular Telephones Pagers Personal Communications Equipment Portable Instrumentation.

TLE6266G : Supply. Fault Tolerant CAN Transceiver With Voltage Regulator Optimized For Automotive Body Applications.

TPS79630DCQ : ti TPS79630, Ultra-low Noise, High Psrr, Fast RF, High-Enable, 1A Low Dropout Regulator.

LTC4261 : Negative Voltage Hot Swap Controller with ADC and I2C Monitoring The LTC4261 negative voltage Hot SwapTM controller allows a board to be safely inserted and removed from a live backplane. Using an external N-channel pass transistor, the board supply voltage can be ramped at an adjustable rate. The device independently adjustable inrush current and overcurrent.

TPS780330220 : Single Output LDO, 150mA, Dual Level Fixed (3.3V Or 2.2V) With Vset Pin, 500nA Quiescent Current The TPS780 family of low-dropout (LDO) regulators offer the benefits of ultralow power (IQ = 500nA), miniaturized packaging (22 SON-6), and selectable dual-level output voltage levels. An adjustable version is also available, but does not have the capability.

ICM7244 : 8-Character, Microprocessor-Compatible, LED Display Decoder Driver The ICM7244 is an 8-character, alphanumeric display driver and controller which provides all the circuitry required to interface a microprocessor or digital system to a 16-segment display with internal pull-up resistors. It is primarily intended for use in microprocessor systems, where.

LT3692 : Monolithic Dual Tracking 3.5A Step-Down Switching Regulator The LT3692 is a dual current mode PWM step-down DC/DC converter with two internal 3.5A switches. Independent input voltage, shutdown, feedback, soft-start, current limit and comparator pins for each channel simplify complex power supply tracking and sequencing requirements..

 
0-C     D-L     M-R     S-Z