Details, datasheet, quote on part number: UCC3804
CategorySemiconductors => Power Management => Offline and Isolated DC/DC Controllers and Converters => PWM and Resonant Controller
Part familyUCC3804 Low-Power BiCMOS Current-Mode PWM
TitleCurrent Mode PWM Controllers
DescriptionLow-Power BiCMOS Current-Mode PWM 8-SOIC 0 to 70
CompanyTexas Instruments, Inc.
DatasheetDownload UCC3804 datasheet
Cross ref.Similar parts: MAX887HESA, MAX887HESA+, MAX887HESA+T, MAX887HESA-T, NCP1010AP130, NCP1011AP130, NCP1011AP130G, UCC2800PW, UCC2801PW, UCC2802PW
Find where to buy
Operating Temperature Range(C)0 to 70
UVLO Thresholds On/Off(V)12.5/8.3
Duty Cycle(Max)(%)50
Approx. Price (US$)1.10 | 1ku
FeaturesError Amplifier,Leading Edge Blanking,Multi-topology,Soft Start
Control MethodCurrent
Gate Drive(Typ)(A)1
  Mecanical Data
Pin nbPackage typeInd stdJEDEC codePackage qtyCarrierDevice markWidth (mm)Length (mm)Thick (mm)Pitch (mm)
8DSOICR-PDSO-G75TUBEUCC3804 3.914.91.581.27
Application notes
• Conditioning a Switch-mode Power Supply Current Signal Using TI Op Amps
The switch-mode power supply primary current is often sensed using a power resistor. Using an op amp to amplify the current-sense signal can reduce cost and improve noise performance and efficiency. This report reviews the advantages of using an op amp cir | Doc
• U-133A UCC3800/1/2/3/4/5 BiCMOS Current Mode Control IC's
The UCC3800 IC has several innovative features for general purpose current-mode controlled applications: high speed circuitry, undervoltage lockout, an op-amp type error amplifier, fast overcurrrent protection, a precision reference and a high-current tote | Doc
• U-111, Practical Considerations in Current Mode Power Supplies
This application note explains the numerous PWM functions and ways to maximize their usefulness. It covers practical circuit design considerations, such as slope compensation, gate drive circuitry, external control functions, synchronization, and paralleli | Doc
• UCC38C42 Family of High-Speed BiCMOS Current-Mode PWM Controllers
Since their introduction in the mid 1980?s, the bipolar UC3842 family of Pulse width modulation (PWM)controllers has grown to become the most widely-used control strategy in the power supply industry. [1] The reasons for success are quite clear, the device | Doc
• Dual Output Boost Converter
The boost converter is modified to provide bipolar 12-V outputs from 5-V supply. Using the UCC3803 to control the basic boost converter building block, the -12-V outputs are generated using a coupled inductor and a flying capacitor. Output voltage regulati | Doc
• DN-42A Design Considerations for Transitioning from UC3842 to the New UCC3802
The UCC3802 offers numerous advantages that allow the power supply design engineer to meet requirements for lower power for battery-operated equipment, higher switching frequencies for reduced magnetics size, higher levels of circuit integration for improv | Doc
• DN-46 Highly Efficient Low Power DC to DC Inverter Converts +5V Input to -3V Out
This design note describes a flyback inverter application using the UCC3805. The application performs three functions: control, switching, and output rectification. A circuit schematic and a list of materials are included. | Doc
• DN-56A, Single Switch Flyback Circuit Converts + 5 V to +/- 12 V for RS-232/422
A bipolar 12V supply from a single +5V input can be developed using a number of conventional approaches. A boost converter is the most logical for the +12V output; however, it cannot be used in some interface-circuit applications. One significant drawback | Doc
• DN-65 Considerations in Powering BiCMOS ICs
Bipolar linear integrated circuits have been with us for years in the form of PWM and PFC controllers, supervisory circuits, and other circuits. Since these devices have traditionally used relatively high-voltage (35V) bipolar processes, powering was not a | Doc
• DN-48 Versatile Low Power SEPIC Converter Accepts Wide Input Voltage Range
This design note describes an output converter for battery-powered and automotive applications. It uses a UCC3803 BiCMOS current-mode controller to provide a 5V output at full load of 100mA from an input of 2.5-13.5V after an initial startup at 5V. The UC3 | Doc
• Understanding Buck-Boost Power Stages in Switchmode Power Supplies (Rev. A) | Doc
• DN-54 Innovative Buck Regulator Uses High Side N-Channel Switch Without Complex
This application note shows how the innovative UCC3803 BiCMOS PWM controller provides very high efficiency without complex gate drives by using a high-side N-channel switch. It converts +5 VDC to +3.3 VDC (or others) and draws only 40 microamps in standby | Doc
• DN-43 Simple Techniques to Generate a Negative Voltage Bias Supply
A low-power negative supply voltage can be developed from a positive input supply using some very common PWM control ICs. Typical applications include generating a -5V to -12V supply for analog function ICs (OP amps), RS-232 communication circuits, and MOS | Doc
• Differences Between the UCC3813 and the UCC3800 PWM Families
This application report discusses the parametric differences between the UCC3813 and UCC3800 PWM families of integrated circuits available from Texas Instruments. | Doc
Spice Model
UCCX804 & UCCx813-4 TINA-TI Transient Spice Model - ZIP (10/11/2011)
UCCx804, UCCx813-4 Families PSpice Transient Model (Rev. B) - ZIP (07/06/2010)
UCCx804 & UCCx813-4 Unencrypted PSpice Transient Model - ZIP (02/18/2016)


Features, Applications


100A Typical Starting Supply Current 500A Typical Operating Supply Current Operation to 1MHz Internal Soft Start Internal Fault Soft Start Internal Leading-Edge Blanking of the Current Sense Signal 1 Amp Totem-Pole Output 70ns Typical Response from Current-Sense to Gate Drive Output 1.5% Tolerance Voltage Reference Same Pinout as UC3842 and UC3842A


The UCC1800/1/2/3/4/5 family of high-speed, low-power integrated circuits contain all of the control and drive components required for off-line and DC-to-DC fixed frequency current-mode switching power supplies with minimal parts count. These devices have the same pin configuration as the UC1842/3/4/5 family, and also offer the added features of internal full-cycle soft start and internal leading-edge blanking of the current-sense input. The UCC1800/1/2/3/4/5 family offers a variety of package options, temperature range options, choice of maximum duty cycle, and choice of critical voltage levels. Lower reference parts such as the UCC1803 and UCC1805 fit best into battery operated systems, while the higher reference and the higher UVLO hysteresis of the UCC1802 and UCC1804 make these ideal choices for use in off-line power supplies. The UCC180x series is specified for operation from C, o the UCC280x series is specified for operation from +85 C, and o the UCC380x series is specified for operation from +70 C.

VCC Voltage (Note 2). 12.0V VCC Current (Note 2). 30.0mA OUT Current. 1.0A OUT Energy (Capacitive Load). 20.0J Analog Inputs (FB, CS). to 6.3V Power Dissipation or J Package). 1.0W Power Dissipation +25C (D Package). 0.65W Storage Temperature Range. to +150C Lead Temperature (Soldering, 10 Seconds). +300C Note 1: Values beyond which damage may occur. All voltages are with respect to GND. All currents are positive into the specified terminal. Consult Unitrode databook for information regarding thermal specifications and limitations of packages. Note 2: In normal operation VCC is powered through a current limiting resistor. Absolute maximum of 12V applies when VCC is driven from a low impedance source such that ICC does not exceed 30mA (which includes gate drive current requirement).

ELECTRICAL CHARACTERISTICS Unless otherwise stated, these specifications apply for TA +125C for TA +85C for TA +70C for UCC380x; VCC=10V (Note 3); RT=100k from REF to RC; CT=330pF from RC to GND; 0.1 F capacitor from VCC to GND; 0.1 F capacitor from VREF to GND. TA=TJ.

PARAMETER TEST CONDITIONS MIN Reference Section Output Voltage Load Regulation Line Regulation VCC=10V to Clamp VCC=10V to Clamp (IVCC=25mA) Total Variation Output Noise Voltage Long Term Stability Output Short Circuit UCCx800/1/2/4 (Note 7) UCCx803/5 (Note 10kHz, TJ=+25C (Note TA=+125C, 1000 Hours (Note mV mV/V V

UCC2800/1/2/3/4/5 UCC3800/1/2/3/4/5 ELECTRICAL CHARACTERISTICS Unless otherwise stated, these specifications apply for TA +125C for TA +85C for TA +70C for UCC380x; VCC=10V (Note 3); RT=100k from REF to RC; CT=330pF from RC to GND; 0.1 F capacitor from VCC to GND; 0.1 F capacitor from VREF to GND. TA=TJ.


Some Part number from the same manufacture Texas Instruments, Inc.
UCC3804D ti UCC3804, Low-power Bicmos Current-mode PWM
UCC3805 Low-power Bicmos Current-mode PWM
UCC38050 Transition Mode PFC Controller
UCC38050D ti UCC38050, Transition Mode PFC Controller
UCC38050DR Transition Mode PFC Controller
UCC38050DR ti UCC38050, Transition Mode PFC Controller
UCC38050P Transition Mode PFC Controller
UCC38050P ti UCC38050, Transition Mode PFC Controller
UCC38051 PFC Controller For Low to Medium Power Applications Requiring Compliance With Iec 1000-3-2
UCC38051D ti UCC38051, PFC Controller For Low to Medium Power Applications Requiring Compliance With Iec 1000-3-2
UCC38051DR PFC Controller For Low to Medium Power Applications Requiring Compliance With Iec 1000-3-2
UCC38051DR ti UCC38051, PFC Controller For Low to Medium Power Applications Requiring Compliance With Iec 1000-3-2
UCC38051P PFC Controller For Low to Medium Power Applications Requiring Compliance With Iec 1000-3-2
UCC38051P ti UCC38051, PFC Controller For Low to Medium Power Applications Requiring Compliance With Iec 1000-3-2
UCC3805D ti UCC3805, Low-power Bicmos Current-mode PWM
UCC3806 Low Power, Dual Output, Current Mode PWM Controller
UCC3806DW ti UCC3806, Low Power, Dual Output, Current Mode PWM Controller
UCC3807 Programmable Maximum Duty Cycle PWM Controller

ADS8344E/2K5 : ti ADS8344, 16-Bit, 8-Channel Serial Output Sampling Analog-to-digital Converter

ONET2511PA : 2.5 GBPS Limiting Amplifier

SN54LS699J : Synchronous Up/down Counters With Output Registers Amd Multiplexed 3-state Outputs

TLV2434AI : Advanced Lincmos(tm) Rail-to-rail Output Wide-input-voltage op Amps

TLV2471AIDR : ti TLV2471A, Single Low-power Rail-to-rail Input/output op Amp

TCM320AC37IPTR : Voice-band Audio Processors Vbape

TL751L10CPE4 : Low-dropout Voltage Regulators

TMS28F400AMT60CDBJL : 65536 BY 8-bit Flash Memory

SN74AUP1G99DCTTG4 : Low-power DUAL 2-input Positive-and GATE

CY29FCT818CTQCTE4 : ti CY29FCT818T, Diagnostic Scan Register

DP83867IRPAPT : Ethernet ICs Gigabit Ethernet PHY Texas Instruments DP83867 Gigabit Ethernet PHY is a robust, low power, fully featured Physical Layer transceiver with integrated PMD sublayers to support 10BASE-T, 100BASE-TX and 1000BASE-T Ethernet protocols. Optimized for ESD protection, the DP83867 exceeds 8kV IEC 61000-4-2. The DP83867 consum

Same catergory

ADP3404 : GSM Power Management System. Handles all GSM Baseband Power Management Functions Four LDOs Optimized for Specific GSM Subsystems Charges Back-Up Capacitor for Real-Time Clock Charge Pump and Logic Level Translators for 3 V and 5 V GSM SIM Modules Narrow Body mm 28-Lead TSSOP Package APPLICATIONS GSM/DCS/PCS Handsets TeleMatic Systems ICO/Iridium Terminals RESET PWRONKEY ROWX POWER-UP.

BA6219B : . The BA6219B and BA6219BFP-Y are reversible-motor drivers suitable for brush motors. Two logic inputs allow four output modes: forward, reverse, idling, and braking. The motor revolving speed can be set arbitrarily by controlling the voltage applied to the motor. FApplications VCRs and cassette tape recorders F 1) Large output current. (IO=2.2A Max.).

EFFH16 : Center Tap. Center Tap, Package : See_factory.


M54640P : Drivers. Stepper Motor Driver. The is a semiconductor IC to drive a stepper motor by the bipolar method. Output MB 1 One-shot-multi T 2 time constant Output power VMM 3 supply 4 GND 5 Power supply VCC Output current value setting Output current direction switching 14 13 GND 9 Io Comparator reference input Comparator input Output current setting Current sensor Output q Bipolar and constant-current.

PT5546A : Plug-in Power Solutions->Non-Isolated->Single Posi. ti PT5546, 10V 1.3A, 5-V Input Step-up (Boost) Isr.

PT6303A : Plug-in Power Solutions->Non-Isolated->Single Posi. ti PT6303, 3.3Vout 3A Wide Input Adjustable Step-down Isr.

PT6715A : Plug-in Power Solutions->Non-Isolated->Single Posi. ti PT6715, 3.3Vout 13 Amp 5V-Input Adjustable Isr, cu Case.

UCC3809D-2 : Current Mode. ti UCC3809-2, Economy Primary Side Controller. User Programmable Soft Start With Active Low Shutdown User Programmable Maximum Duty Cycle Accessible 5V Reference Undervoltage Lockout Operation 0.4A Source/0.8A Sink FET Driver Low 100A Startup Current The UCC3809 family of BCDMOS economy low power integrated circuits contains all the control and drive circuitry required for off-line and isolated.

UCC381DP-5 : ti UCC381-5, Low Power 1 Ampere Low Dropout (LDO) Regulator. Precision Positive Linear Voltage Regulation 0.5V Dropout at 1A Guaranteed Reverse Input/ Output Voltage Isolation with Low Leakage Low Quiescent Current Irrespective of Load Adjustable Output Voltage Version Fixed Versions for 3.3V and 5V Outputs Logic Shutdown Capability Short Circuit Power Limit of 3% VIN Current Limit Remote Load Voltage for Accurate.

TL2575HV-33 : The TL2575 and TL2575HV greatly simplify the design of switching power supplies by conveniently providing all the active functions needed for a step-down (buck) switching regulator in an integrated circuit. Accepting a wide input voltage range of up to 60 V (HV version) and available in fixed output voltages of 3.3 V, 5 V, 12 V, 15 V, or an adjustable-output.

HV852 : The Supertex HV852 is a high voltage, low noise EL (electroluminescent) lamp driver. It is the low noise version of the HV852 with improved EMI performance, operating over an input voltage range of 3.2V to 5.0V. It is designed to drive EL lamps of up to 1.5in2, with capacitive values up to 5.3nF. The HV853 converts a low voltage DC input to a high voltage.

ISL60002BAH333 : Precision 3.300V Low Power FGA Reference The ISL60002 FGA voltage references are very high precision analog voltage references fabricated in Intersil's proprietary Floating Gate Analog technology and feature low supply voltage operation at ultra-low 400nA operating current. Additional include guaranteed initial accuracy as low as 1.0mV, @ 20ppm/oC.

AS1321 : Step-up DC-DC Converter The AS1321 is a high-efficiency step-up DC-DC converter designed to generate a fixed voltage of +5.0V. The AS1321 achieves an efficiency of up to 96%. The minimum input voltage is 1.5V, the output voltage is fixed at 5.0V, and output current is up to 130mA (@ 2V VBATT)..

TLC5946 : 16-Channel, 12-bit PWM LED Driver With 6-Bit Dot Correction The TLC5946 is a 16-channel, constant current sink LED driver. Each channel is individually adjustable with 4096 pulse-width modulated (PWM) steps and 64 constant current sink steps for dot correction. The dot correction adjusts the brightness variations between LEDs. Both grayscale control.

EVAL5985 : Power Management Ics 2 A step-down switching regulator demonstration board based on the L5985.

0-C     D-L     M-R     S-Z