Details, datasheet, quote on part number: UCC3804D
PartUCC3804D
CategorySemiconductors => Power Management => Offline and Isolated DC/DC Controllers and Converters => PWM and Resonant Controller
Part familyUCC3804 Low-Power BiCMOS Current-Mode PWM
TitleCurrent Mode
DescriptionLow-Power BiCMOS Current-Mode PWM 8-SOIC 0 to 70
CompanyTexas Instruments, Inc.
StatusACTIVE
ROHSY
SampleYes
DatasheetDownload UCC3804D datasheet
Cross ref.Similar parts: UCC2804DTR, UCC2804D, UCC3804DTR, LM3478, LM5001, LM5002, TL2842, TL2842B, TL2843
Quote
Find where to buy
 
Specifications 
Operating Temperature Range(C)0 to 70
UVLO Thresholds On/Off(V)12.5/8.3
Frequency(Max)(kHz)1000
RatingCatalog
Vin(Min)(V)12.5
Duty Cycle(Max)(%)50
TopologyBoost,Buck,Flyback,Forward
Package GroupPDIP,SOIC,TSSOP
Approx. Price (US$)1.10 | 1ku
FeaturesError Amplifier,Leading Edge Blanking,Multi-topology,Soft Start
Control MethodCurrent
Gate Drive(Typ)(A)1
Vin(Max)(V)400
  Mecanical Data
Pin nbPackage typeInd stdJEDEC codePackage qtyCarrierDevice markWidth (mm)Length (mm)Thick (mm)Pitch (mm)
8DSOICR-PDSO-G75TUBEUCC3804 3.914.91.581.27
Application notes
• Conditioning a Switch-mode Power Supply Current Signal Using TI Op Amps
The switch-mode power supply primary current is often sensed using a power resistor. Using an op amp to amplify the current-sense signal can reduce cost and improve noise performance and efficiency. This report reviews the advantages of using an op amp cir | Doc
• U-133A UCC3800/1/2/3/4/5 BiCMOS Current Mode Control IC's
The UCC3800 IC has several innovative features for general purpose current-mode controlled applications: high speed circuitry, undervoltage lockout, an op-amp type error amplifier, fast overcurrrent protection, a precision reference and a high-current tote | Doc
• U-111, Practical Considerations in Current Mode Power Supplies
This application note explains the numerous PWM functions and ways to maximize their usefulness. It covers practical circuit design considerations, such as slope compensation, gate drive circuitry, external control functions, synchronization, and paralleli | Doc
• UCC38C42 Family of High-Speed BiCMOS Current-Mode PWM Controllers
Since their introduction in the mid 1980?s, the bipolar UC3842 family of Pulse width modulation (PWM)controllers has grown to become the most widely-used control strategy in the power supply industry. [1] The reasons for success are quite clear, the device | Doc
• Dual Output Boost Converter
The boost converter is modified to provide bipolar 12-V outputs from 5-V supply. Using the UCC3803 to control the basic boost converter building block, the -12-V outputs are generated using a coupled inductor and a flying capacitor. Output voltage regulati | Doc
• DN-42A Design Considerations for Transitioning from UC3842 to the New UCC3802
The UCC3802 offers numerous advantages that allow the power supply design engineer to meet requirements for lower power for battery-operated equipment, higher switching frequencies for reduced magnetics size, higher levels of circuit integration for improv | Doc
• DN-46 Highly Efficient Low Power DC to DC Inverter Converts +5V Input to -3V Out
This design note describes a flyback inverter application using the UCC3805. The application performs three functions: control, switching, and output rectification. A circuit schematic and a list of materials are included. | Doc
• DN-56A, Single Switch Flyback Circuit Converts + 5 V to +/- 12 V for RS-232/422
A bipolar 12V supply from a single +5V input can be developed using a number of conventional approaches. A boost converter is the most logical for the +12V output; however, it cannot be used in some interface-circuit applications. One significant drawback | Doc
• DN-65 Considerations in Powering BiCMOS ICs
Bipolar linear integrated circuits have been with us for years in the form of PWM and PFC controllers, supervisory circuits, and other circuits. Since these devices have traditionally used relatively high-voltage (35V) bipolar processes, powering was not a | Doc
• DN-48 Versatile Low Power SEPIC Converter Accepts Wide Input Voltage Range
This design note describes an output converter for battery-powered and automotive applications. It uses a UCC3803 BiCMOS current-mode controller to provide a 5V output at full load of 100mA from an input of 2.5-13.5V after an initial startup at 5V. The UC3 | Doc
• Understanding Buck-Boost Power Stages in Switchmode Power Supplies (Rev. A) | Doc
• DN-54 Innovative Buck Regulator Uses High Side N-Channel Switch Without Complex
This application note shows how the innovative UCC3803 BiCMOS PWM controller provides very high efficiency without complex gate drives by using a high-side N-channel switch. It converts +5 VDC to +3.3 VDC (or others) and draws only 40 microamps in standby | Doc
• DN-43 Simple Techniques to Generate a Negative Voltage Bias Supply
A low-power negative supply voltage can be developed from a positive input supply using some very common PWM control ICs. Typical applications include generating a -5V to -12V supply for analog function ICs (OP amps), RS-232 communication circuits, and MOS | Doc
• Differences Between the UCC3813 and the UCC3800 PWM Families
This application report discusses the parametric differences between the UCC3813 and UCC3800 PWM families of integrated circuits available from Texas Instruments. | Doc
Spice Model
UCCX804 & UCCx813-4 TINA-TI Transient Spice Model - ZIP (10/11/2011)
UCCx804, UCCx813-4 Families PSpice Transient Model (Rev. B) - ZIP (07/06/2010)
UCCx804 & UCCx813-4 Unencrypted PSpice Transient Model - ZIP (02/18/2016)

 

Features, Applications

FEATURES

100A Typical Starting Supply Current 500A Typical Operating Supply Current Operation to 1MHz Internal Soft Start Internal Fault Soft Start Internal Leading-Edge Blanking of the Current Sense Signal 1 Amp Totem-Pole Output 70ns Typical Response from Current-Sense to Gate Drive Output 1.5% Tolerance Voltage Reference Same Pinout as UC3842 and UC3842A

DESCRIPTION

The UCC1800/1/2/3/4/5 family of high-speed, low-power integrated circuits contain all of the control and drive components required for off-line and DC-to-DC fixed frequency current-mode switching power supplies with minimal parts count. These devices have the same pin configuration as the UC1842/3/4/5 family, and also offer the added features of internal full-cycle soft start and internal leading-edge blanking of the current-sense input. The UCC1800/1/2/3/4/5 family offers a variety of package options, temperature range options, choice of maximum duty cycle, and choice of critical voltage levels. Lower reference parts such as the UCC1803 and UCC1805 fit best into battery operated systems, while the higher reference and the higher UVLO hysteresis of the UCC1802 and UCC1804 make these ideal choices for use in off-line power supplies. The UCC180x series is specified for operation from C, o the UCC280x series is specified for operation from +85 C, and o the UCC380x series is specified for operation from +70 C.

VCC Voltage (Note 2). 12.0V VCC Current (Note 2). 30.0mA OUT Current. 1.0A OUT Energy (Capacitive Load). 20.0J Analog Inputs (FB, CS). to 6.3V Power Dissipation or J Package). 1.0W Power Dissipation +25C (D Package). 0.65W Storage Temperature Range. to +150C Lead Temperature (Soldering, 10 Seconds). +300C Note 1: Values beyond which damage may occur. All voltages are with respect to GND. All currents are positive into the specified terminal. Consult Unitrode databook for information regarding thermal specifications and limitations of packages. Note 2: In normal operation VCC is powered through a current limiting resistor. Absolute maximum of 12V applies when VCC is driven from a low impedance source such that ICC does not exceed 30mA (which includes gate drive current requirement).

ELECTRICAL CHARACTERISTICS Unless otherwise stated, these specifications apply for TA +125C for TA +85C for TA +70C for UCC380x; VCC=10V (Note 3); RT=100k from REF to RC; CT=330pF from RC to GND; 0.1 F capacitor from VCC to GND; 0.1 F capacitor from VREF to GND. TA=TJ.

PARAMETER TEST CONDITIONS MIN Reference Section Output Voltage Load Regulation Line Regulation VCC=10V to Clamp VCC=10V to Clamp (IVCC=25mA) Total Variation Output Noise Voltage Long Term Stability Output Short Circuit UCCx800/1/2/4 (Note 7) UCCx803/5 (Note 10kHz, TJ=+25C (Note TA=+125C, 1000 Hours (Note mV mV/V V

UCC2800/1/2/3/4/5 UCC3800/1/2/3/4/5 ELECTRICAL CHARACTERISTICS Unless otherwise stated, these specifications apply for TA +125C for TA +85C for TA +70C for UCC380x; VCC=10V (Note 3); RT=100k from REF to RC; CT=330pF from RC to GND; 0.1 F capacitor from VCC to GND; 0.1 F capacitor from VREF to GND. TA=TJ.


 

Related products with the same datasheet
UCC3804DTR
UCC3804N
UCC3804PW
UCC3804PWTR
Some Part number from the same manufacture Texas Instruments, Inc.
UCC3804DTR ti UCC3804, Low-power Bicmos Current-mode PWM
UCC3805 Low-power Bicmos Current-mode PWM
UCC38050 Transition Mode PFC Controller
UCC38050D ti UCC38050, Transition Mode PFC Controller
UCC38050DR Transition Mode PFC Controller
UCC38050DR ti UCC38050, Transition Mode PFC Controller
UCC38050P Transition Mode PFC Controller
UCC38050P ti UCC38050, Transition Mode PFC Controller
UCC38051 PFC Controller For Low to Medium Power Applications Requiring Compliance With Iec 1000-3-2
UCC38051D ti UCC38051, PFC Controller For Low to Medium Power Applications Requiring Compliance With Iec 1000-3-2
UCC38051DR PFC Controller For Low to Medium Power Applications Requiring Compliance With Iec 1000-3-2
UCC38051DR ti UCC38051, PFC Controller For Low to Medium Power Applications Requiring Compliance With Iec 1000-3-2
UCC38051P PFC Controller For Low to Medium Power Applications Requiring Compliance With Iec 1000-3-2
UCC38051P ti UCC38051, PFC Controller For Low to Medium Power Applications Requiring Compliance With Iec 1000-3-2
UCC3805D ti UCC3805, Low-power Bicmos Current-mode PWM
UCC3806 Low Power, Dual Output, Current Mode PWM Controller
UCC3806DW ti UCC3806, Low Power, Dual Output, Current Mode PWM Controller
UCC3807 Programmable Maximum Duty Cycle PWM Controller
UCC3807-1
UCC3807-2
UCC3807-3
Same catergory

BQ2204APN : NVSRAM Power Management. ti BQ2204A, SRAM Nonvolatile Controller ic For 4 SRAM Banks.

CM5001 : High Current Silicon Bridge Rectifier ( Voltage 50 to 1000 Volts Current - 50 Ampere ).

MAX6332 : Low-Voltage. 3-Pin, Ultra-Low-Voltage, Low-power P Reset Circuits. The MAX6332/MAX6333/MAX6334 microprocessor (P) supervisory circuits monitor the power supplies 3.3V P and digital systems. They increase circuit reliability and reduce cost by eliminating external components and adjustments. These devices perform a single function: they assert a reset signal whenever the VCC supply voltage declines below a preset.

MC33470 : Synchronous Rectification, DC/DC Converter, Programmable Integrated Controller.

NJU7223 : 500mA Low Dropout Voltage Regulator. I GENERAL The NJU7223 series is a high precision output voltage, low drop output, low current consumption and high output current 3-terminal positive voltage regulator with a over current protection and a thermal shutdown. Low dropout voltage is realized at high current output. I PACKAGE OUTLINE I 123 GHigh Precision Output Voltage 2% GHigh Output.

NJU7333 : Single-phase DC Brnshless Motor Driver ic. s GENERAL s PACKAGE OUTLINE The is a single-phase DC brushless motor driver IC for small fan-motor and high power applications. It MOS-FET driver circuit for better saturation characteristics. Slew late of amplifiers and feedback resistors are optimized to achieve low-noise motor operation. Maximum output current is 500mA. The NJU7333 includes. frequency.

PJ7800BSeries : . hese voltage regulators are monolithic integrated circuits designed as fixed-voltage regulators for a wide With adequate heatsinking they can deliver output currents to 1 ampere. Although designed primarily as a fixed voltage regulator, these devices can be used with external components to obtain adjustable voltages and currents. variety of applications.

PT506XSeries : Low Current. +5v to +12v/15v 9w Dual Output Integrated Switching Regulator.

RBM-0505D : Unregulated DC/DC. Power = 1 ;; ISOlation = 3 ;; Input Voltages (VDC) = 1.8, 3.3, 5, 9, 12, 15, 24 ;; Output Voltages (VDC) = 1.8, 3.3, 5, 9, 12, 15, 24 ;; No. Of Outputs = S & D ;; Case = SIP6 Micro.

TPS7325 : . TPS7348Q, TPS7350Q LOW-DROPOUT VOLTAGE REGULATORS WITH INTEGRATED DELAYED RESET FUNCTION Available 3.3-V, 4.85-V, and 5-V Fixed-Output and Adjustable Versions Integrated Precision Supply-Voltage Supervisor Monitoring Regulator Output Voltage Active-Low Reset Signal with 200-ms Pulse Width Very Low Dropout Voltage. Maximum mA (TPS7350) Low Quiescent.

W005G : 1.5A Glass Passivated Bridge Rectifier. Glass Passivated Die Construction High Case Dielectric Strength of 1500V RMS Low Reverse Leakage Current Surge Overload Rating to 40A Peak Ideal for Printed Circuit Board Applications Plastic Material - UL Flammability Classification 94V-0 UL Listed Under Recognized Component Index, File Number E94661 Case: Molded Plastic Terminals: Plated Leads, Solderable.

MAX17003 : Fixed-frequency with optimal interleaving minimizes input ripple current from the lowest input voltages up to 26V The MAX17003/MAX17004 are dual step-down, switch-mode, power-supply (SMPS) controllers with synchronous rectification, intended for main 5V/3.3V power generation in battery-powered systems. Fixed-frequency operation with optimal interleaving.

SMA6821MP : High Voltage 3-Phase Motor Drivers The SLA6800MP and SMA6800MP Series inverter power module (IPM) devices provides a robust, highly-integrated solution for optimally controlling 3-phase motor power inverter systems and variable speed control systems used in energy-conserving designs to drive motors of residential and commercial appliances. These ICs take.

MAX9937 : Automotive Current-Sense Amplifier With Reverse-Battery Protection The MAX9937 is a tiny automotive grade current-sense amplifier designed for unidirectional high-side current-sense applications. This device addresses major areas of concern for automotive applications including load-dump protection up to +40V, reverse-battery protection, and filtering.

LT3758 : High Input Voltage, Boost, Flyback, SEPIC And Inverting Controller The LT3758 is a wide input range, current mode, DC/DC controller which is capable of generating either positive or negative output voltages. It can be configured as either a boost, flyback, SEPIC or inverting converter. The LT3758 drives a low side external N-channel power MOSFET from.

PT7M7824Y : P Supervisor Circuits The PT7M7xxx family microprocessor (P) supervisory circuits are targeted to improve reliability and accuracy of power-supply circuitry in P systems. These devices reduce the complexity and number of components required to monitor power-supply and battery functions..

 
0-C     D-L     M-R     S-Z