Details, datasheet, quote on part number: UCC3805D
PartUCC3805D
CategorySemiconductors => Power Management => Offline and Isolated DC/DC Controllers and Converters => PWM and Resonant Controller
Part familyUCC3805 Low-Power BiCMOS Current-Mode PWM
TitleCurrent Mode
DescriptionLow-Power BiCMOS Current-Mode PWM 8-SOIC 0 to 70
CompanyTexas Instruments, Inc.
StatusACTIVE
ROHSY
SampleYes
DatasheetDownload UCC3805D datasheet
Cross ref.Similar parts: UCC2805D, UCC2805DTR, UCC2805D, UCC3805DTR, LM3478, LM5001, LM5002, TL2842, TL2842B
Quote
Find where to buy
 
Specifications 
Operating Temperature Range(C)0 to 70
Frequency(Max)(kHz)1000
RatingCatalog
Duty Cycle(Max)(%)50
UVLO Thresholds On/Off(V)4.1/3.6
TopologyBoost,Buck,Flyback,Forward
Package GroupPDIP,SOIC,TSSOP
Approx. Price (US$)1.10 | 1ku
FeaturesError Amplifier,Leading Edge Blanking,Multi-topology,Soft Start
Control MethodCurrent
Gate Drive(Typ)(A)1
Vin(Min)(V)4.1
Vin(Max)(V)400
  Mecanical Data
Pin nbPackage typeInd stdJEDEC codePackage qtyCarrierDevice markWidth (mm)Length (mm)Thick (mm)Pitch (mm)
8DSOICR-PDSO-G75TUBEUCC3805 3.914.91.581.27
Application notes
• Conditioning a Switch-mode Power Supply Current Signal Using TI Op Amps
The switch-mode power supply primary current is often sensed using a power resistor. Using an op amp to amplify the current-sense signal can reduce cost and improve noise performance and efficiency. This report reviews the advantages of using an op amp cir | Doc
• U-133A UCC3800/1/2/3/4/5 BiCMOS Current Mode Control IC's
The UCC3800 IC has several innovative features for general purpose current-mode controlled applications: high speed circuitry, undervoltage lockout, an op-amp type error amplifier, fast overcurrrent protection, a precision reference and a high-current tote | Doc
• U-111, Practical Considerations in Current Mode Power Supplies
This application note explains the numerous PWM functions and ways to maximize their usefulness. It covers practical circuit design considerations, such as slope compensation, gate drive circuitry, external control functions, synchronization, and paralleli | Doc
• UCC38C42 Family of High-Speed BiCMOS Current-Mode PWM Controllers
Since their introduction in the mid 1980?s, the bipolar UC3842 family of Pulse width modulation (PWM)controllers has grown to become the most widely-used control strategy in the power supply industry. [1] The reasons for success are quite clear, the device | Doc
• Dual Output Boost Converter
The boost converter is modified to provide bipolar 12-V outputs from 5-V supply. Using the UCC3803 to control the basic boost converter building block, the -12-V outputs are generated using a coupled inductor and a flying capacitor. Output voltage regulati | Doc
• DN-42A Design Considerations for Transitioning from UC3842 to the New UCC3802
The UCC3802 offers numerous advantages that allow the power supply design engineer to meet requirements for lower power for battery-operated equipment, higher switching frequencies for reduced magnetics size, higher levels of circuit integration for improv | Doc
• DN-46 Highly Efficient Low Power DC to DC Inverter Converts +5V Input to -3V Out
This design note describes a flyback inverter application using the UCC3805. The application performs three functions: control, switching, and output rectification. A circuit schematic and a list of materials are included. | Doc
• DN-56A, Single Switch Flyback Circuit Converts + 5 V to +/- 12 V for RS-232/422
A bipolar 12V supply from a single +5V input can be developed using a number of conventional approaches. A boost converter is the most logical for the +12V output; however, it cannot be used in some interface-circuit applications. One significant drawback | Doc
• DN-65 Considerations in Powering BiCMOS ICs
Bipolar linear integrated circuits have been with us for years in the form of PWM and PFC controllers, supervisory circuits, and other circuits. Since these devices have traditionally used relatively high-voltage (35V) bipolar processes, powering was not a | Doc
• DN-48 Versatile Low Power SEPIC Converter Accepts Wide Input Voltage Range
This design note describes an output converter for battery-powered and automotive applications. It uses a UCC3803 BiCMOS current-mode controller to provide a 5V output at full load of 100mA from an input of 2.5-13.5V after an initial startup at 5V. The UC3 | Doc
• Understanding Buck-Boost Power Stages in Switchmode Power Supplies (Rev. A) | Doc
• DN-54 Innovative Buck Regulator Uses High Side N-Channel Switch Without Complex
This application note shows how the innovative UCC3803 BiCMOS PWM controller provides very high efficiency without complex gate drives by using a high-side N-channel switch. It converts +5 VDC to +3.3 VDC (or others) and draws only 40 microamps in standby | Doc
• DN-43 Simple Techniques to Generate a Negative Voltage Bias Supply
A low-power negative supply voltage can be developed from a positive input supply using some very common PWM control ICs. Typical applications include generating a -5V to -12V supply for analog function ICs (OP amps), RS-232 communication circuits, and MOS | Doc
• Differences Between the UCC3813 and the UCC3800 PWM Families
This application report discusses the parametric differences between the UCC3813 and UCC3800 PWM families of integrated circuits available from Texas Instruments. | Doc
Spice Model
UCCX805 & UCCX813-5 TINA-TI Transient Spice Model - ZIP (10/11/2011)
UCCx805 & UCCx813-5 Unencrypted PSpice Transient Model - ZIP (02/18/2016)
UCCx805, UCCx813-5 Families PSpice Transient Model (Rev. B) - ZIP (07/06/2010)

 

Features, Applications

FEATURES

100A Typical Starting Supply Current 500A Typical Operating Supply Current Operation to 1MHz Internal Soft Start Internal Fault Soft Start Internal Leading-Edge Blanking of the Current Sense Signal 1 Amp Totem-Pole Output 70ns Typical Response from Current-Sense to Gate Drive Output 1.5% Tolerance Voltage Reference Same Pinout as UC3842 and UC3842A

DESCRIPTION

The UCC1800/1/2/3/4/5 family of high-speed, low-power integrated circuits contain all of the control and drive components required for off-line and DC-to-DC fixed frequency current-mode switching power supplies with minimal parts count. These devices have the same pin configuration as the UC1842/3/4/5 family, and also offer the added features of internal full-cycle soft start and internal leading-edge blanking of the current-sense input. The UCC1800/1/2/3/4/5 family offers a variety of package options, temperature range options, choice of maximum duty cycle, and choice of critical voltage levels. Lower reference parts such as the UCC1803 and UCC1805 fit best into battery operated systems, while the higher reference and the higher UVLO hysteresis of the UCC1802 and UCC1804 make these ideal choices for use in off-line power supplies. The UCC180x series is specified for operation from C, o the UCC280x series is specified for operation from +85 C, and o the UCC380x series is specified for operation from +70 C.

VCC Voltage (Note 2). 12.0V VCC Current (Note 2). 30.0mA OUT Current. 1.0A OUT Energy (Capacitive Load). 20.0J Analog Inputs (FB, CS). to 6.3V Power Dissipation or J Package). 1.0W Power Dissipation +25C (D Package). 0.65W Storage Temperature Range. to +150C Lead Temperature (Soldering, 10 Seconds). +300C Note 1: Values beyond which damage may occur. All voltages are with respect to GND. All currents are positive into the specified terminal. Consult Unitrode databook for information regarding thermal specifications and limitations of packages. Note 2: In normal operation VCC is powered through a current limiting resistor. Absolute maximum of 12V applies when VCC is driven from a low impedance source such that ICC does not exceed 30mA (which includes gate drive current requirement).

ELECTRICAL CHARACTERISTICS Unless otherwise stated, these specifications apply for TA +125C for TA +85C for TA +70C for UCC380x; VCC=10V (Note 3); RT=100k from REF to RC; CT=330pF from RC to GND; 0.1 F capacitor from VCC to GND; 0.1 F capacitor from VREF to GND. TA=TJ.

PARAMETER TEST CONDITIONS MIN Reference Section Output Voltage Load Regulation Line Regulation VCC=10V to Clamp VCC=10V to Clamp (IVCC=25mA) Total Variation Output Noise Voltage Long Term Stability Output Short Circuit UCCx800/1/2/4 (Note 7) UCCx803/5 (Note 10kHz, TJ=+25C (Note TA=+125C, 1000 Hours (Note mV mV/V V

UCC2800/1/2/3/4/5 UCC3800/1/2/3/4/5 ELECTRICAL CHARACTERISTICS Unless otherwise stated, these specifications apply for TA +125C for TA +85C for TA +70C for UCC380x; VCC=10V (Note 3); RT=100k from REF to RC; CT=330pF from RC to GND; 0.1 F capacitor from VCC to GND; 0.1 F capacitor from VREF to GND. TA=TJ.


 

Related products with the same datasheet
UCC3805DTR
UCC3805N
UCC3805PW
UCC3805PWTR
Some Part number from the same manufacture Texas Instruments, Inc.
UCC3805DTR ti UCC3805, Low-power Bicmos Current-mode PWM
UCC3806 Low Power, Dual Output, Current Mode PWM Controller
UCC3806DW ti UCC3806, Low Power, Dual Output, Current Mode PWM Controller
UCC3807 Programmable Maximum Duty Cycle PWM Controller
UCC3807-1
UCC3807-2
UCC3807-3
UCC3807D-1 ti UCC3807-1, Programmable Maximum Duty Cycle PWM Controller
UCC3807D-2 ti UCC3807-2, Programmable Maximum Duty Cycle PWM Controller
UCC3807D-3 ti UCC3807-3, Programmable Maximum Duty Cycle PWM Controller
UCC3807DTR-1 ti UCC3807-1, Programmable Maximum Duty Cycle PWM Controller
UCC3807DTR-2 ti UCC3807-2, Programmable Maximum Duty Cycle PWM Controller
UCC3807DTR-3 ti UCC3807-3, Programmable Maximum Duty Cycle PWM Controller
UCC3807N-1 ti UCC3807-1, Programmable Maximum Duty Cycle PWM Controller
UCC3807N-2 ti UCC3807-2, Programmable Maximum Duty Cycle PWM Controller
UCC3807N-3 ti UCC3807-3, Programmable Maximum Duty Cycle PWM Controller
UCC3808 2 - Low Power Current Mode Push-pull PWM
UCC3808-1
UCC3808-2
UCC38083 Current Mode Push-pull PWM With Programmable Slope Compensation
UCC38083D ti UCC38083, Current Mode Push-pull PWM With Programmable Slope Compensation
Same catergory

5962-9232501MXA : Motor Control Bridges. LMD18200 - 3A, 55V H-Bridge, Package: Cerdip, Pin Nb=24.

AD4016M166RBA-5 : Low Voltage Operation is More Suitable to be Used on Battery Backup, Portable Electronic.

AN7709F : Low-dropout Three-pin Voltage Regulator 1.2-a Type. The AN7700, AN7700F, and AN7700SP series are stabilized constant-voltage power supplies with small difference between I/O voltages (0.5 V typ.). They are suitable for low-voltage, battery-driven equipment, and home appliances and industrial equipment with great fluctuation of the supply voltage. The output voltage ranges: For 20 V, and 24 V For 12 V, and V AN7700.

GBP005 : Single Phase Glass Passivated Bridge Rectifier. Ideal for printed circuit board Reliable low cost construction utilizing molded plastic technique Surge overload rating: 50A peak SINGLE PHASE GLASS PASSIVATED BRIDGE RECTIFIER . Terminal: Plated leads solderable per MIL-STD 202E, method 208C. Case: UL-94 Class V-0 recognized Flame Retardant Epoxy. Polarity: Polarity symbol marked on body. Mounting.

L4940Series : Very Low Drop 1.5a Regulator. PRECISE 10, 12V OUTPUTS LOW DROPOUT VOLTAGE (500mV Typ. at 1.5A) VERY LOW QUIESCENT CURRENT THERMAL SHUTDOWN SHORT CIRCUIT PROTECTION REVERSE POLARITY PROTECTION The L4940 series of three terminal positive regulators is available TO-220, TO-220FP and D2PAK packages and with several fixed output voltages, making it useful in a wide range of industrial.

LP3984 : Positive Voltage->Fixed. LP3984 - Micropower, 150mA Ultra Low-dropout CMOS Voltage Regulator in Subminiature 4-I/O Micro SMD Package, Package: Microsmd, Pin Nb=4.

LTC1517-3.3 : Inductorless DC/DC Converters->20mA Max Output Cur. LTC1517-3.3, 15mA Micropower, Regulated 3.3V Charge Pump in a 5-Pin SOT-23 Package.

MC79M12BDT-1 : Three-terminal Negative Fixed Voltage Regulators. The MC79M00 series of fixed output negative voltage regulators are intended as complements to the popular MC78M00 series devices. Available in fixed output voltage options 8.0, 12 and 15 V, these regulators employ current limiting, thermal shutdown, and safearea compensation making them remarkably rugged under most operating conditions. With adequate.

MCT7818BD2T : Three-terminal Positive Fixed Voltage Regulators. These voltage regulators are monolithic integrated circuits designed as fixed-voltage regulators for a wide variety of applications including local, on-card regulation. These regulators employ internal current limiting, thermal shutdown, and safe-area compensation. With adequate heatsinking they can deliver output currents in excess 1.0 A. Although.

NJM2885 : Low Dropout Voltage Regulator. s GENERAL The NJM2885 is low dropout voltage regulator designed for portable application. Advanced Bipolar technology achieves low noise, high ripple rejection and low quiescent current. s qHigh Ripple Rejection 75dB typ. (f=1kHz) qOutput Noise Voltage Vno=45Vrms qOutput capacitor with 2.2F ceramic capacitor (Vo2.7V) qOutput Current Io(max.)=500mA.

P6LU-0505EH52 : Power/w = 1 ;; Input/vdc = 5/12/24 ;; Output/vdc = 3,3/5/7,2/12/15/18 ;; ISOlation = 5200V ;; Package = SIP7.

PT5026 : Non-Isolated DC-DC Converters. Positive Input/Negative Output Integrated Switching Regulator Negative Output Input Voltage Range: to +7 Volts Laser-Trimmed Small Footprint Soft Start 5-Pin Mount Option (Suffixes & M) The PT5020 series of integrated switching regulators (ISRs) convert a positive input voltage, typically to a negative output voltage for a wide range of analog and datacom.

PT6886 : Non-Isolated DC-DC Converters. 5A Non-Isolated Output >90% Efficiency Low-cost Alternative to Isolated Converters to 36V Input Voltage Range Adjustable Output Voltage Output Remote Sense Standby Function Solderable Copper Case Surface Mountable IPC Lead Free 2 The PT6880 product family is a series of highly efficient, non-isolated integrated switching regulator (ISR) modules.

TPS75833 : . Fixed-Output and Adjustable Versions Dropout Voltage Typically A (TPS75833) Low 125 A Typical Quiescent Current Fast Transient Response 3% Tolerance Over Specified Conditions for Fixed-Output Versions Available 5-Pin TO220 and TO263 Surface-Mount Packages Thermal Shutdown Protection TO220 (KC) PACKAGE (TOP VIEW) EN IN GND OUTPUT FB/NC EN IN GND OUTPUT.

TPS76925DBVR : ti TPS76925, Ultra Low-power 100-mA Low-dropout (LDO) Line Regulators.

UCC283 : Low Dropout 3 Ampere Linear Regulator Family. Precision Positive Series Pass The UCC283-3/-5/-ADJ family of positive linear series pass regulators are tailored Voltage Regulation for low drop out applications where low quiescent power is important. Fabricated with a BiCMOS technology ideally suited for low input to output differential applica 0.45V Dropout at 3A tions, the UCC283-5 will pass 3A while.

 
0-C     D-L     M-R     S-Z