|
Details, datasheet, quote on part number:856019
| |
| Part: | 856019 |
| Category: | RF & Microwaves => Filters => SAW (Surface Acoustic Wave) Filters |
| Description: | Description = Filter - STD 140 High-selectivity ;; Frequency (MHz) = 140 ;; Bandwidth (MHz) = 28 ;; Insertion Loss (dB) = 21.0 Max ;; Modes of Operation = se ;; Package (mm) = 9.0 X 7.0 |
| Company: | TriQuint Semiconductor |
| Datasheet: | Download 856019 datasheet File size : 550 kB |
| Request For quote: | Find where to buy 856019
|
| |
Datasheet text preview:
Preliminary Data Sheet
Features
· · · · · · · For broadband applications Typical 3 dB bandwidth of 28.5 MHz High attenuation Single-ended operation Ceramic Surface Mount Package (SMP) Small size Replaces Sawtek P/N 851935
Part Number 856019 140 MHz SAW Filter
·
Package
Surface Mount 9.00 x 7.01 x 1.50 mm
Pin Configuration
Bottom View
1 2 3
10
1.50 NOM. 1.65 MAX. 9.00 2.54 1.80 0.76
4
9
5
8
7
6
7.01
2.54
1.12 1.02 x 2.54 1.02
Pin No. 4 5 9 10 1,2,3,6,7,8
Description Output Output return Input Input return Case ground
Dimensions shown are nominal in millimeters All tolerances are ±0.15mm except overall length and width +0.10mm/-0.15mm Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 0.5 - 1.0µm, over a 2 - 6µm Ni plating
Subject to change or obsolescence without notice
Rev C
11-Jul-2002
Page 1 of 5
Preliminary Data Sheet
Operating Temperature Range: (2) 0 to +70 oC
Part Number 856019 140 MHz SAW Filter
Electrical Specifications (1)
Parameter (3)
Center Frequency Maximum Insertion Loss Lower 1 dB Bandedge (4) Upper 1 dB Bandedge Lower 3 dB Bandedge (4) Upper 3 dB Bandedge Lower 40 dB Bandedge (4) Upper 40 dB Bandedge Amplitude Variation 127.2 - 152.8 MHz Phase Linearity 127.2 - 152.8 MHz Group Delay Variation 127.2 - 152.8 MHz Absolute Delay Relative Attenuation (4) 15 - 90 MHz 90 - 121.5 MHz 158.5 - 190 MHz 190 - 350 MHz Terminating Source Impedance (5) Terminating Load Impedance (5) Substrate Material Temperature Coefficient of Frequency Notes:
1. 2. 3. 4. 5. All specifications are based on the test circuit shown below In production, devices will be tested at room temperature to a guardbanded specification to ensure electrical compliance over temperature Electrical margin has been built into the design to account for the variations due to temperature and manufacturing tolerances All attenuation measurements are measured relative to minimum insertion loss This is the optimum impedance in order to achieve the performance shown
Minimum
152.8 153.7 121.5 45 40 37 42 -
Typical
140 20 126.45 153.75 125.53 154.46 122.45 157.41 0.7 4.3 22 0.66 50 45 43 51 50 50 128 LiNbO3 -74
Maximum
21 127.2 126.3 158.5 1.0 7 50 -
Unit
MHz dB MHz MHz MHz dB p-p deg p-p ns p-p µsec dB dB dB dB ppm/ oC
Test Circuit:
68nH 9 4 50 91nH
50 Single-ended
50
1,2,3,5 6,7,8,10
Subject to change or obsolescence without notice
Rev C
11-Jul-2002
Page 2 of 5
Preliminary Data Sheet
Part Number 856019 140 MHz SAW Filter
Typical Performance (at +25oC)
Subject to change or obsolescence without notice
Rev C
11-Jul-2002
Page 3 of 5
Preliminary Data Sheet
68nH 9 4 91nH
Part Number 856019 140 MHz SAW Filter
Matching Schematics
50 Single-ended
50
1,2,3,5 6,7,8,10
50
Marking
PCB Footprint
9.19 1.32
ID dot
SAWTEK 856019 XXXXXX
1.22
Date code
7.21
3.76
2.07
1.22
1.32 1.32
The date code consists of: day of the current year (Julian, 3 digits), last digit of the year (1 digit) and hour (2 digits)
This footprint represents a recommendation only Dimensions shown are nominal in millimeters
Tape and Reel
2.7 16.8 Ø330
0.3 2.0 4.0 Ø1 .5 A 1.75 7.5 16.0 7.22 12.0 A
ID dot
9.22
Ø102
Ø20.2 Ø13.0
2.0
Direction of travel
2.2 Section A-A
Ø1.5
Dimensions shown are nominal in millimeters Packaging quantity: 2000 units/reel
Subject to change or obsolescence without notice
Rev C
11-Jul-2002
Page 4 of 5
Preliminary Data Sheet
Maximum Ratings
Parameter
Operating Temperature Range Storage Temperature Range
Part Number 856019 140 MHz SAW Filter
Symbol
T Tstg
Minimum
0 -40
Typical
+25 -
Maximum
+70 +85
Unit
o o
C C
Warnings
· · Electrostatic Sensitive Device (ESD) Avoid ultrasonic exposure
Links to Additional Technical Information
PCB Layout Tips S-Parameters Qualification Flowchart Reel and Packaging Label Soldering Profile Other Technical Information
Sawtek's liability is limited only to the Surface Acoustic Wave (SAW) component(s) described in this data sheet. Sawtek does not accept any liability for applications, processes, circuits or assemblies which are implemented using any Sawtek component described in this data sheet.
Contact Information
PO Box 609501 Orlando, FL 32860-9501 USA
Subject to change or obsolescence without notice
Phone: +1 (407) 886-8860 Fax: +1 (407) 886-7061 Email: custservice@sawtek.com Web: www.sawtek.com
Rev C
Or contact one of our worldwide Network of sales offices, Representatives or distributors
11-Jul-2002
Page 5 of 5
|
|
