|
Details, datasheet, quote on part number:856064
| |
| Part: | 856064 |
| Category: | RF & Microwaves => Filters => SAW (Surface Acoustic Wave) Filters |
| Description: | Description = Filter - STD 140 High-selectivity ;; Frequency (MHz) = 140 ;; Bandwidth (MHz) = 2 ;; Insertion Loss (dB) = 22.186 Max ;; Modes of Operation = se ;; Package (mm) = 19.0 X 6.5 |
| Company: | TriQuint Semiconductor |
| Datasheet: | Download 856064 datasheet File size : 580 kB |
| Request For quote: | Find where to buy 856064
|
| |
Datasheet text preview:
Preliminary Data Sheet
Features
· · · · · · For IF applications Typical 3 dB bandwidth of 2 MHz High attenuation Single-ended operation Ceramic Surface Mount Package (SMP) Replaces Sawtek P/N 851905 (BW 3dB = 2.0MHz)
Part Number 856064 140 MHz SAW Filter
·
Package
Surface Mount 19.00 x 6.50 x 1.75 mm
Pin Configuration
Bottom View
1
2
3
4
5
1.75 NOM. 1.96 MAX. 0.76
10 9
8
7
6
19.0 1.80 1.91 R0.51 6.50 2.31
1.02
Pin No. 5 10 1,6 2,3,4 7,8,9
Description RF output RF input Ground Case ground Case ground
Dimensions shown are nominal in millimeters All tolerances are ±0.15mm except overall length and width +0.15mm/-0.10mm Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 0.5 - 1.0µm, over a 2 - 6µm Ni plating
Subject to change or obsolescence without notice
Rev A
06-Sep-2002
Page 1 of 5
Preliminary Data Sheet
Operating Temperature Range: (2) 0 to +70 oC
Part Number 856064 140 MHz SAW Filter
Electrical Specifications (1)
Parameter (3)
Center Frequency Minimum Insertion Loss Lower 1 dB Bandedge (4) Upper 1 dB Bandedge Lower 3 dB Bandedge (4) Upper 3 dB Bandedge Lower 40 dB Bandedge (4) Upper 40 dB Bandedge Amplitude Variation 139.15 - 140.85 MHz Phase Linearity 139.15 - 140.85 MHz Group Delay Variation 139.15 - 140.85 MHz Relative Attenuation (4) 15 - 136 MHz 144 - 220 MHz 220 - 230 MHz 230 - 250 MHz 250 - 260 MHz 260 - 350 MHz Terminating Source Impedance: (5) Terminating Load Impedance: (5) Substrate Material Notes:
1. 2. 3. 4. 5. All specifications are based on the test circuit shown below In production, devices will be tested at room temperature to a guardbanded specification to ensure electrical compliance over temperature Electrical margin has been built into the design to account for the variations due to temperature and manufacturing tolerances All attenuation measurements are measured relative to minimum insertion loss This is the optimum impedance in order to achieve the performance shown
Minimum
140.845 141.022 138.272 60 45 38 45 26 45 -
Typical
140 21.5 139.06 140.94 138.91 141.09 138.31 141.67 0.5 1.8 85 64 56 46 65 31 65 50 50 Quartz
Maximum
22.186 139.155 138.978 141.726 1.0 3.5 180 -
Unit
MHz dB MHz MHz MHz MHz MHz MHz dB p-p deg p-p ns p-p dB dB dB dB dB dB -
Test Circuit:
Actual matching values may vary due to PCB layout and parasitics
47nH 10 5 18pF 50 110nH
50 Single-ended
50
1,2,3,4 6,7,8,9
Subject to change or obsolescence without notice
Rev A
06-Sep-2002
Page 2 of 5
Preliminary Data Sheet
Part Number 856064 140 MHz SAW Filter
Typical Performance (at +25oC)
Subject to change or obsolescence without notice
Rev A
06-Sep-2002
Page 3 of 5
Preliminary Data Sheet
Actual matching values may vary due to PCB layout and parasitics
47nH 10 5 110nH
Part Number 856064 140 MHz SAW Filter
Matching Schematics
50 Single-ended
50
1,2,3,4 6,7,8,9
18pF
50
Marking
PCB Footprint
8.84
SAWTEK 856064 XXXXXX
ID Dot Date Code
6.70
2.00
1.22
.69
The date code consists of: day of the current year (Julian, 3 digits), last digit of the year (1 digit) and hour (2 digits)
This footprint represents a recommendation only Dimensions shown are nominal in millimeters
Tape and Reel
2.7 32.8 Ø330 ID dot
0.3 2.0 4.0 Ø1.5 R0.75 A 1.75
14.2 19.6 32.0 28.4
Ø102
Ø20.2 Ø13.0
2.0
0.20
Direction of travel
2.3 Section A-A
7.1
12.0
Ø1.5
A
Dimensions shown are nominal in millimeters Packaging quantity: 2000 units/reel
Subject to change or obsolescence without notice
Rev A
06-Sep-2002
Page 4 of 5
Preliminary Data Sheet
Maximum Ratings
Parameter
Operating Temperature Range Storage Temperature Range
Part Number 856064 140 MHz SAW Filter
Symbol
T Tstg
Minimum
0 -40
Maximum
+70 +85
Unit
o o
C C
Warnings
· · Electrostatic Sensitive Device (ESD) Avoid ultrasonic exposure
Links to Additional Technical Information
PCB Layout Tips S-Parameters Qualification Flowchart Soldering Profile Other Technical Information
Sawtek's liability is limited only to the Surface Acoustic Wave (SAW) component(s) described in this data sheet. Sawtek does not accept any liability for applications, processes, circuits or assemblies which are implemented using any Sawtek component described in this data sheet.
Contact Information
PO Box 609501 Orlando, FL 32860-9501 USA
Subject to change or obsolescence without notice
Phone: +1 (407) 886-8860 Fax: +1 (407) 886-7061 Email: custservice@sawtek.com Web: www.sawtek.com
Rev A
Or contact one of our worldwide network of sales offices, representatives or distributors
06-Sep-2002
Page 5 of 5
|
|
