|
Details, datasheet, quote on part number:856069
| |
| Part: | 856069 |
| Category: | RF & Microwaves => Filters => SAW (Surface Acoustic Wave) Filters |
| Description: | Description = Filter - STD 140 High-selectivity ;; Frequency (MHz) = 140 ;; Bandwidth (MHz) = 10 ;; Insertion Loss (dB) = 21.7 Max ;; Modes of Operation = se ;; Package (mm) = 13.3 X 6.5 |
| Company: | TriQuint Semiconductor |
| Datasheet: | Download 856069 datasheet File size : 662 kB |
| Request For quote: | Find where to buy 856069
|
| |
Datasheet text preview:
Data Sheet
Features
· · · · · · · · For broadband applications Typical 3 dB bandwidth of 10 MHz High attenuation No impedance matching required for operation at 50 Single-ended operation Ceramic Surface Mount Package (SMP) Small size Replaces Sawtek P/N 851921 (BW 3dB=10 MHz)
Part Number 856069 140 MHz SAW Filter
·
Package
Surface Mount 13.3 x 6.50 x 1.50 mm
Pin Configuration
Bottom View
1
2
3
4
5
1.50 NOM. 1.65 MAX. 0.64
10
13.3 1.80 1.91
9
8
7
6
6.50
R0.51 2.31 1.02
Pin No. 1 5 6 10 2,3,4 7,8,9
Description Input return Output Output return Input Case ground Case ground
Dimensions shown are nominal in millimeters All tolerances are ±0.15mm except overall length and width ±0.10mm Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 0.5 - 1.0µm, over a 2 - 6µm Ni plating
Subject to change or obsolescence without notice
Rev -
08-Oct-2002
Page 1 of 5
Data Sheet
Operating Temperature Range: (2) -30 to +85 oC
Part Number 856069 140 MHz SAW Filter
Electrical Specifications (1)
Parameter (3)
Center Frequency Minimum Insertion Loss Lower 1 dB Bandedge (4) Upper 1 dB Bandedge Lower 3 dB Bandedge (4) Upper 3 dB Bandedge Lower 40 dB Bandedge (4) Upper 40 dB Bandedge Amplitude Variation 135.524 - 144.508 MHz Phase Linearity 135.524 - 144.508 MHz Group Delay Variation 135.524 - 144.508 MHz Absolute Delay Relative Attenuation (4) 15 - 130 MHz 130 - 133 MHz 147 - 150 MHz 150 - 350 MHz Source Impedance (5) Load Impedance (5) Substrate Material Temperature Coefficient of Frequency Notes:
1. 2. 3. 4. 5.
Minimum
144.508 145 133.379 47.8 52 50.6 51.3 -
Typical
140 20.87 135.38 144.79 135.00 145.24 133.85 146.72 0.7 5 45 1.52 50 57 53 53 50 50 LINbO3 -94
Maximum
21.7 135.524 135 146.551 0.94 6.31 57.3 -
Unit
MHz dB MHz MHz MHz MHz MHz MHz dB deg nsec µsec dB dB dB dB ppm/oC
All specifications are based on the test circuit shown below In production, devices will be tested at room temperature to a guardbanded specification to ensure electrical compliance over temperature Electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing tolerances All attenuation measurements are measured relative to minimum insertion loss This is the optimum impedance in order to achieve the performance shown
Test Circuit:
15nH 10 5 1,2,3,4 6,7,8,9 50 68nH
50 Single-ended
50
No impedance matching required
Subject to change or obsolescence without notice
Rev -
08-Oct-2002
Page 2 of 5
Data Sheet
Part Number 856069 140 MHz SAW Filter
Typical Performance (at +25oC)
Subject to change or obsolescence without notice
Rev -
08-Oct-2002
Page 3 of 5
Data Sheet
15nH 10 5 1,2,3,4 6,7,8,9 68nH
Part Number 856069 140 MHz SAW Filter
Matching Schematics
50 Single-ended
50
50
No impedance matching required
Marking
PCB Footprint
8.84
SAWTEK 856069 XXXXXX
6.70
2.00
1.22
.69
The date code consists of: JJJ = Julian day, Y = last digit of year, M = manufacturing site code
This footprint represents a recommendation only Dimensions shown are nominal in millimeters
Tape and Reel
24.8 2.7 Ø330 ID dot
0.3 2.0 4.0 Ø1.5 A 1.75 11.5 13.9 24
Ø102
Direction of travel Ø20.2 Ø13.0 2.0
2.3 Section A-A 7.1 12.0 Ø1.5 A
Dimensions shown are nominal in millimeters Packaging quantity:2000 units/reel
Subject to change or obsolescence without notice
Rev -
08-Oct-2002
Page 4 of 5
Data Sheet
Maximum Ratings
Parameter
Operating Temperature Range Storage Temperature Range
Part Number 856069 140 MHz SAW Filter
Symbol
T Ts t g
Minimum
-30 -40
Maximum
+85 +85
Unit
o o
C C
Warnings
· · Electrostatic Sensitive Device (ESD) Avoid ultrasonic exposure
Links to Additional Technical Information
PCB Layout Tips S-Parameters Qualification Flowchart Soldering Profile Other Technical Information
Sawtek's liability is limited only to the Surface Acoustic Wave (SAW) component(s) described in this data sheet. Sawtek does not accept any liability for applications, processes, circuits or assemblies which are implemented using any Sawtek component described in this data sheet.
Contact Information
PO Box 609501 Orlando, FL 32860-9501 USA
Subject to change or obsolescence without notice
Phone: +1 (407) 886-8860 Fax: +1 (407) 886-7061 Email: custservice@sawtek.com Web: www.sawtek.com
Rev -
Or contact one of our worldwide Network of sales offices, Representatives or distributors
08-Oct-2002
Page 5 of 5
|
|
