|
|
Part: M55310/18-C01A
Category:
Timing Circuits
-> Oscillators
Description: .01Hz - 15MHz Crystal Oscillator
Company: Vectron International
Datasheet: Download M55310/18-C01A datasheet File size : 245 kB
Request For quote: Find where to buy M55310/18-C01A
Datasheet text preview:
INCH-POUND MIL-PRF-55310/18D 8 July 2002 SUPERSEDING MIL-PRF-55310/18C 25 March 1998
PERFORMANCE SPECIFICATION SHEET OSCILLATOR, CRYSTAL CONTROLLED, TYPE 1 (CRYSTAL OSCILLATOR (XO)), 0.01 Hz THROUGH 15.0 MHz, HERMETIC SEAL, SQUARE WAVE, CMOS This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification and MIL-PRF-55310. Pin number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Inches .002 .018 .100 .150 .20 mm 0.05 0.46 2.54 3.81 5.1 Function NC NC NC NC NC NC B - (GND/CASE) OUTPUT NC NC NC NC NC B+ mm 6.9 7.62 11.2 13.7 22.53
Inches .27 .300 .44 .54 .887
NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerances are ±.005 (0.13 mm) for three place decimals and ±.02 (0.5 mm) for two place decimals. 4. All pins with NC function may be connected internally and are not to be used as external tie points or connections. FIGURE 1. Dimensions and configuration.
AMSC N/A 1 of 5 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
FSC 5955
MIL-PRF-55310/18D REQUIREMENTS: Interface and physical dimensions: See figure 1. Mounting: See figure 1. Terminals: See figure 1. Seal: Hermetic in accordance with MIL-PRF-55310, maximum leakage rate 5 x 10 atm cc/s. Weight: 0.5 ounce, maximum. * Oscillator: Class 2 (see 1.2.3 of MIL-PRF-55310). Calibration: Manufacturer calibrated. * Screening: In accordance with MIL-PRF-55310, product level B or S, as applicable. Temperature: Operating: See table I. Storage: -62°C to +125°C. Oscillator load: 10 kilohms ±5 percent shunted by 15 pF ±5 percent capacitor for CMOS compatible square. Output waveform: Symmetrical square wave. Output voltage: At designated CMOS load. Logic 1: See table I. Logic 0: See table I. Rise and fall times: See table I. Duty cycle: 40 to 60 percent duty cycle. Supply voltage: See table I. Input current: At designated supply voltage (see table I). Output frequency: Frequency as designated at time of acquisition (see table I). Initial accuracy at reference temperature (up to 30 days after shipment): See table I. Initial frequency-temperature accuracy (one-half temperature cycle): Verification applicable. 1/ Frequency-temperature tolerance (one-half temperature cycle, referenced to frequency measured at +23°C ±1°C, immediately prior to starting of the test): See table I. Measurements taken at ten equally spaced increments over the specified operating temperature range. 1/ 1/ For the purpose of transitioning this device to MIL-PRF-55310, `Frequency stability versus temperature' has been renamed `Frequency-temperature tolerance'. The verification requirements of `initial frequencytemperature accuracy (one-half temperature cycle)' shall apply except that frequency measurements shall be referenced to the frequency measured at +23°C ±1°C (fref) instead of to the nominal frequency (fnom).
-8
2
TABLE I. Dash numbers and operating characteristics.
Dash number Output frequency range Supply voltage ±10% Maximum Input current at maximum supply voltage 1/ mA 25 25 20 20 15 15 10 10 3 3 Output voltage Rise and fall times (max) Initial accuracy ppm at +23°C ±1°C Frequency aging ppm/year after 30 days Frequency-temperature tolerance (ppm)
Logic: 1 (min)
Logic: 0 (max)
-55°C to +125°C A ±50 ±100 ±50 ±100 ±50 ±100 ±50 ±100 ±50 ±100
-55°C to +105°C B ±40 ±80 ±40 ±80 ±40 ±80 ±40 ±80 ±40 ±80
-20°C to +70°C C ±25 ±50 ±25 ±50 ±25 ±50 ±25 ±50 ±25 ±50
01 02 11 12 21 22 31 32 41 42
0.01 Hz to 15.0 MHz 0.01 Hz to 12.0 MHz 0.01 Hz to 10.0 MHz 0.01 Hz to 8.0 MHz 0.01 Hz to 5.0 MHz
V dc +15 +15 +12 +12 +10 +10 +8 +8 +5 +5
V dc 12.8 12.8 10.2 10.2 8.5 8.5 6.8 6.8 4.2 4.2
V dc 1.5 1.5 1.2 1.2 1.0 1.0 0.8 0.8 0.5 0.5
ns 30 30 35 35 40 40 50 50 70 70
±15 ±25 ±15 ±25 ±15 ±25 ±15 ±25 ±15 ±25
±5 ±10 ±5 ±10 ±5 ±10 ±5 ±10 ±5 ±10
1/ Maximum input current for no load condition. Actual configuration of CMOS loads must be added to determine power supply requirements.
Others parts begin by m5
|
|
|
