|
|
Part: TSOP2130SA1
Category:
Description: IR Receiver Modules For Remote Control Systems
Company: Vishay Intertechnology
Datasheet: Download TSOP2130SA1 datasheet File size : 55 kB
Request For quote: Find where to buy TSOP2130SA1
Datasheet text preview:
VISHAY
TSOP21..SA1
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
Description
The TSOP21..SA1 - series are miniaturized receivers for infrared remote control systems. PIN diode and preamplifier are assembled on lead frame, the epoxy package is designed as IR filter. The demodulated output signal can directly be decoded by a microprocessor. The main benefit is the reliable function even in disturbed ambient and the protection against uncontrolled output pulses.
16125
Features
· Photo detector and preamplifier in one package · Internal filter for PCM frequency · Improved shielding against electrical field disturbance · TTL and CMOS compatibility · Output active low · Low power consumption · High immunity against ambient light
Parts Table
Par t TSOP2130SA1 TSOP2133SA1 TSOP2136SA1 TSOP2137SA1 TSOP2138SA1 TSOP2140SA1 TSOP2156SA1 30 kHz 33 kHz 36 kHz 36.7 kHz 38 kHz 40 kHz 56 kHz Carr ier Frequency
Special Features
· Enhanced data rate of 4000 bit/s · Operation with short bursts possible ( 6 cycles/ burs t )
Application Circuit
Transmitter TSOPxxxx with TSALxxxx
Circuit
R1 = 100 VS C1 = 4.7 µF VO +VS
Block Diagram
2 25 k Input PIN AGC Band Pass Demodulator
VS
OUT GND
µC
GND
1
OUT
R1 + C1 recommended to suppress power supply disturbances. The output voltage should not be hold continuously at a voltage below VO = 3.3 V by the external circuit.
3 Control Circuit
GND
Document Number 82160 Rev. 2, 15-Oct-2002
www.vishay.com 1
TSOP21..SA1
Vishay Semiconductors Absolute Maximum Ratings
Tamb = 25 °C, unless otherwise specified Parameter S upply Voltage Supply Current Output Voltage Output Current Junction Temperature Storage Temperature Range Operating Temperature Range Power Consumption Soldering Temperature (Tamb 85 °C) t 10 s, 1 mm from case (Pin 2) (Pin 2) (Pin 1) (Pin 1) Test condition Symbol VS IS VO IO Tj Tstg Tamb Ptot Tsd Value
VISHAY
Unit V mA V mA °C °C °C mW °C
- 0.3 to + 6.0 5 - 0.3 to + 6.0 5 100 - 25 to + 85 - 25 to + 85 50 260
Electrical and Optical Characteristics
Tamb = 25 °C, unless otherwise specified Parameter S upply Current (Pin 2) S upply Voltage (Pin 2) Transmission Distance Output Voltage Low (Pin 1) Irradiance (30 - 40 kHz) Irradiance (56 kHz) Irradiance Directivity Ev = 0, test signal see fig.3, IR diode TSAL6200, IF = 250 mA IOL = 0.5 mA, Ee = 0.7 mW/m 2, f = fo, test signal see fig.1 Pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig.3 Pulse width tolerance: tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig.3 Test signal see fig. 1 Angle of half transmission distance Test condition VS = 5 V, Ev = 0 VS = 5 V, Ev = 40 klx, sunlight Symbol ISD ISH VS d VOL Ee min Ee min Ee max 1 / 2 30 ± 45 0.2 0.3 4.5 35 250 0.4 0.5 Min 0.8 Typ. 1.1 1.4 5.5 Max 1.5 Unit mA mA V m mV
mW/m2 mW/m2 W/m2 deg
Typical Characteristics (Tamb = 25°C unless otherwise specified)
Ee Optical Test Signal (IR diode TSAL6200, IF=0.4 A, N=6 pulses, f=f0, T=10 ms)
t po Output Pulse Width ( ms )
0.35 0.30 Output Pulse 0.25 0.20 0.15 0.10 0.05 0.00 0.1
16907
tpi *) T *) tpi w 6/fo is recommended for optimal function Output Signal VO VOH VOL td1 )
1) 2)
t
Input Burst Duration l = 950 nm, optical test signal, fig.1
14337
3/f0 < td < 9/f0 tpi 4/f0 < tpo < tpi + 6/f0 t
tpo2 )
1.0
10.0
100.0 1000.0 10000.0
Ee Irradiance ( mW/m2 )
Figure 1. Output Function
Figure 2. Pulse Length and Sensitivity in Dark Ambient
Document Number 82160 Rev. 2, 15-Oct-2002
www.vishay.com 2
VISHAY
TSOP21..SA1
Vishay Semiconductors
Ee
Optical Test Signal
Ee min Threshold Irradiance ( mW/m 2 )
4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 0.01 Ambient, l = 950 nm
Correlation with ambient light sources: 10W/m2^1.4klx (Std.illum.A,T=2855K) 10W/m2^8.2klx (Daylight,T=5900K)
600 ms T = 60 ms Output Signal, ( see Fig.4 )
600 ms
t
94 8134
VO VOH VOL
Ton
Toff
t
16911
0.10
1.00
10.00
100.00
E Ambient DC Irradiance (W/m2)
Figure 3. Output Function
Figure 6. Sensitivity in Bright Ambient
0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0.1 1.0 l = 950 nm, optical test signal, fig.3 Toff Ton
Ee min Threshold Irradiance ( mW/m 2 )
Ton ,Toff Output Pulse Width ( ms )
1.0
2.0 f = fo f = 10 kHz 1.0
1.5
f = 1 kHz
0.5 f = 100 Hz 0.0 0.1 1.0 10.0 100.0 1000.0
10.0
100.0 1000.0 10000.0
16912
16910
Ee Irradiance ( mW/m2 )
DVsRMS AC Voltage on DC Supply Voltage (mV)
Figure 4. Output Pulse Diagram
Figure 7. Sensitivity vs. Supply Voltage Disturbances
E e min Threshold Irradiance ( mW/m 2 )
1.2
E e min / E e Rel. Responsivity
2.0 f(E) = f0 1.6 1.2 0.8 0.4 0.0 0.0 0.4 0.8 1.2 1.6 2.0 E Field Strength of Disturbance ( kV/m )
1.0 0.8 0.6 0.4 0.2 0.0 0.7 f = f0"5% Df ( 3dB ) = f0/7 0.9 1.1 1.3
16926
f/f0 Relative Frequency
94 8147
Figure 5. Frequency Dependence of Responsivity
Figure 8. Sensitivity vs. Electric Field Disturbances
Document Number 82160 Rev. 2, 15-Oct-2002
www.vishay.com 3
Others parts begin by ts
TS-1 TS-2 TS-3 TS-4 TS-5 TS-6 TS-7 TS-8 TS-9 TS-10 TS-11 TS-12 TS-13 TS-14 TS-15 TS-16 TS-17 TS-18 TS-19 TS-20 TS-21 TS-22 TS-23 TS-24 TS-25 TS-26 TS-27 TS-28 TS-29 TS-30 TS-31 TS-32 TS-33 TS-34 TS-35 TS-36 TS-37 TS-38 TS-39 TS-40 TS-41 TS-42 TS-43 TS-44 TS-45 TS-46
|
|
|
