|
Details, datasheet, quote on part number:X24640P-2.5
| |
Datasheet text preview:
64K
X24640
400KHz 2-Wire Serial E2PROM with Block LockTM
DESCRIPTION
8K x 8 Bit
FEATURES
·
· ·
·
· · · · · · · · ·
Save Critical Data with Programmable Block Lock Protection --Block Lock (0, 1/4, 1/2, or all of E2PROM Array) --Software Program Protection --Programmable Hardware Write Protect In Circuit Programmable ROM Mode 400KHz 2-Wire Serial Interfac --Schmitt Trigger Input Noise Suppression --Output Slope Control for Ground Bounce Noise Elimination Longer Battery Life With Lower Power --Active Read Current Less Than 1mA --Active Program Current Less Than 3mA --Standby Current Less Than 1µA 1.8V to 3.6V, 2.5V to 5.5V and 4.5V to 5.5V Power Supply Versions 32 Word Page Write Mode --Minimizes Total Write Time Per Word Internally Organized 8K x 8 Bidirectional Data Transfer Protocol Self-Timed Write Cycle --Typical Write Cycle Time of 5ms High Reliability --Endurance: 100,000 Cycles --Data Retention: 100 Years 8-Lead SOIC 20-Lead TSSOP 8-Lead PDIP
The X24640 is a CMOS Serial E2PROM, internally organized 8K x 8. The device features a serial interface and software protocol allowing operation on a simple two wire bus. The bus operates at 400 KHz all the way down to 1.8V. Three device select inputs (S0S2) allow up to eight devices to share a common two wire bus. A Write Protect Register at the highest address location, FFFFh, provides three write protection features: Software Write Protect, Block Lock Protect, and Programmable Hardware Write Protect. The Software Write Protect feature prevents any nonvolatile writes to the device until the WEL bit in the Write Protect Register is set. The Block Lock Protection feature gives the user four array block protect options, set by programming two bits in the Write Protect Register. The Programmable Hardware Write Protect feature allows the user to install the device with WP tied to VCC, program and Block Lock the desired portions of the memory array in circuit, and then enable the In Circuit Programmable ROM Mode by programming the WPEN bit in the Write Protect Register. After this, the Block Locked portions of the array, including the Write Protect Register itself, are permanently protected from being erased.
FUNCTIONAL DIAGRAM
SERIAL E2PROM DATA AND ADDRESS (SDA) DATA REGISTER Y DECODE LOGIC COMMAND DECODE AND CONTROL LOGIC BLOCK LOCK AND WRITE PROTECT CONTROL LOGIC S2 S1 S0 DEVICE SELECT LOGIC WRITE PROTECT REGISTER 4K x 8 SERIAL E2PROM ARRAY 8K x 8 2K x 8
SCL
PAGE DECODE LOGIC
2K x 8
WP
WRITE VOLTAGE CONTROL
7038 FM 01
©Xicor, 1995, 1996 Patents Pending 7038-1.2 4/25/97 T0/C2/D0 SH
1
Characteristics subject to change without notice
X24640
Xicor E2PROMs are designed and tested for applications requiring extended endurance. Inherent data retention is greater than 100 years. PIN DESCRIPTIONS Serial Clock (SCL) The SCL input is used to clock all data into and out of the device. Serial Data (SDA) SDA is a bidirectional pin used to transfer data into and out of the device. It is an open drain output and may be wire-ORed with any number of open drain or open collector outputs. An open drain output requires the use of a pull-up resistor. For selecting typical values, refer to the Pullup resistor selection graph at the end of this data sheet. Device Select (S0, S1, S2) The device select inputs (S0, S1, S2) are used to set the first three bits of the 8-bit slave address. This allows up to eight devices to share a common bus. These inputs can be static or actively driven. If used statically they must be tied to VSS or VCC as appropriate. If actively driven, they must be driven with CMOS levels (driven to VCC or VSS). Write Protect (WP) The Write Protect input controls the Hardware Write Protect feature. When held LOW, Hardware Write Protection is disabled. When this input is held HIGH, and the WPEN bit in the Write Protect Register is set HIGH, the Write Protect Register is protected, preventing changes to the Block Lock Protection and WPEN bits.
* .197" S0 S1 S2 VSS
PIN NAMES Symbol
S0, S1, S2 SDA SCL WP VSS VCC NC
Description
Device Select Inputs Serial Data Serial Clock Write Protect Ground Supply Voltage No Connect
7038 FM T01
PIN CONFIGURATION
Not to scale 8-Lead PDIP/SOIC 1 2 3 4 * .244" X24640 8 7 6 5 VCC WP SCL SDA
20-Lead TSSOP
NC S0 S1 NC 0.300" Max NC NC S2 VSS NC NC
1 2 3 4 5 6 7 8 9 10
20 20 19 19 18 18 17 17 16 16
X24640 15 15
NC VCC WP NC NC NC SCL SDA NC NC
14 14 13 13 12 12 11 1 0.252"
* SOIC Measurement
7038 FM 02
2
X24640
DEVICE OPERATION The device supports a bidirectional bus oriented protocol. The protocol defines any device that sends data onto the bus as a transmitter, and the receiving device as the receiver. The device controlling the transfer is a master and the device being controlled is the slave. The master will always initiate data transfers, and provide the clock for both transmit and receive operations. Therefore, the device will be considered a slave in all applications. Clock and Data Conventions Data states on the SDA line can change only during SCL LOW. SDA state changes during SCL HIGH are reser ved for indicating start and stop conditions. Refer to Figures 1 and 2. Start Condition All commands are preceded by the start condition, which is a HIGH to LOW transition of SDA when SCL is HIGH. The device continuously monitors the SDA and SCL lines for the start condition and will not respond to any command until this condition has been met.
Figure 1. Data Validity
SCL
SDA DATA STABLE DATA CHANGE
7038 FM 03
Figure 2. Definition of Start and Stop
SCL
SDA START BIT STOP BIT
7038 FM 04
3
|
|
