|
Details, datasheet, quote on part number:QC6117
| |
Datasheet text preview:
QC6117 Series
DS3883-1.2 September 1993
QC6117 Series
200KHz to 16MHz QUARTZ CRYSTAL OSCILLATORS
The QC6117 Series oscillator is a ruggedised simple p a c k a g e d oscillator designed for space and military applications where radiation hardness is a significant factor in the use of this product.
FEATURES
I Ceramic Chip Carrier Package I Radiation Hard Design I Low Power Consumption I CMOS Output I Small Size
ELECTRICAL SPECIFICATION
FREQUENCY RANGE FREQUENCY STABILITY
200KHz to 16 MHz ±100ppm Max. All causes (including frequency/temperature, frequency adjustment, ageing, load and voltage coefficients, environmental and radiation).
OPERATING TEMPERATURE RANGE OUTPUT Voltage Fan Out Mark/Space Ratio At VDD/2 Rise and Fall Time (between 0.3 & 0.7 VDD) START UP TIME SUPPLY Voltage Current VDD Unloaded Logic `0' Logic `1'
-55 to +125°C
0.1 VDD Max. 0.9 VDD Min. 2 CMOS Gates 60:40 - 40:60 10nS Max. 20mS Max.
+10V ±1.0V 20mA Max.
ENVIRONMENTAL SPECIFICATION
BUMP SEVERITY 4000 ±10 bumps at 390m/s2 peak acceleration, pulse duration 6ms in each direction of three mutually perpedicular axes. 10 to 60Hz 3.5 peak displacement 60 to 5000Hz 490m/s2 peak accn. 5 sweeps at 1 octave/min. in each of three mutually perpedicular axes (4hr 30mins. total). 0.5g2/Hz between 20Hz and 2kHz. Duration 30 mins. in each of three mutually perpedicular axes. 14715m/s2 peak acceleration for 0.5ms duration half sine pulse. 5 shocks in each direction of three mutually perpendicular axes.
VIBRATION SEVERITY (SINUSOIDAL)
VIBRATION SEVERITY (RANDOM)
SHOCK SEVERITY
ACCELERATION (STEADY STATE) Screening Only 49050m/s2 steady acceleration for 1 min. duration in the Y1 direction.
1
QC6117 Series
CLIMATIC CATEGORY STORAGE TEMPERATURE RANGE RADIATION HARDNESS Gamma Total Dose Transient Gamma Neutrons 10MRad typical, cobalt 60 source at 1MRad/hour rate. Output will be within specification not more than 10µs after exposure to 10KRad (Si) pulse at 1x1011 Rad/s peak dose, pulse width 70ns. Total fluence, 3x1014 neutrons/cm2 (1 MeV Si eqt). 55/125/56 -55°C to +150°C
MECHANICAL SPECIFICATION
WEIGHT (TYPICAL) OUTLINE DRAWING 1.1 grammes
Pin Connections 7 9 23 24 28 29 32 33 37 Note A Output Note A Note A +10V Note A Note A Gnd Note A
Notes: A) Internally connected. No external electrical connections possible. B) All other pins may have external electrical connections. Dimensions in mm (inches).
MARKING
The following information is indelibly marked on the top surface of each device and on each primary package: 1. GPS Logo 2. The nominal output frequency in 'kHz' or 'MHz' as appropriate 3. The type number 4. The data code in accordance with Clause 22 of BS9000: Part 1: 1981 5. The primary package is marked to indicate device static sensitivity 6. Customised marking is available on request
2
QC6117 Series
CONDITIONING Acceleration (steady-state) High Temperature Rapid Change of Temperature Power Burn-In 49050 m/s2 steady acceleration for 1 minute duration in the Y1 direction 24 hrs. at +150°C 10 cycles -55°C to +125°C 160 hrs. at +125°C
GENERAL NOTES
STATIC PRECAUTIONS All quartz crystal oscillators can contain devices which are deemed to be static sensitive. Full handling precautions must be followed at all times when dealing with these devices. Failure to do so may result in damage to the product. A useful guide is BS5783 1987 'Code of practice for Handling ESD'.
MECHANICAL PRECAUTIONS Handling Care must be taken to avoid damage during use of the device. GPS product is built to withstand normal assembly practices, however, levels of shock or vibration in excess of those specified may result in degraded performance or in extreme cases total failure of the product.
ORDERING INFORMATION
When Ordering Please Quote: The series number: QC6117. The required frequency. Our Sales Desk will be happy to advise upon any other parameters which require more detailed attention.
SPECIFICATION VARIATIONS
In the event that your exact requirements are not entirely met by this specification you should note that varients of this series are availble. Indeed this device can be fully customised to your exact specification. For details of this please contact our Sales Desk.
HEADQUARTERS OPERATIONS GEC PLESSEY SEMICONDUCTORS Cheney Manor, Swindon, Wiltshire, SN2 2QW, United Kingdom. Tel: (0793) 518000 Fax: (0793) 518411 GEC PLESSEY SEMICONDUCTORS P.O. Box 660017, 1500 Green Hills Road, Scotts Valley, CA 95067-0017, United States of America. Tel: (408) 438 2900 Fax: (408) 438 5576
CUSTOMER SERVICE CENTRES
· · · · · · · ·
FRANCE & BENELUX Les Ulis Cedex Tel: (1) 64 46 23 45 Tx: 602858 Fax: (1) 64 46 06 07 GERMANY Munich Tel: (089) 3609 06-0 Tx: 523980 Fax: (089) 3609 06-55 ITALY Milan Tel: (02) 66040867 Fax: (02) 66040993 JAPAN Tokyo Tel: (03) 3296-0281 Fax: (03) 3296-0228 NORTH AMERICA Integrated Circuits and Microwave Products Scotts Valley Tel: (408) 438 2900 Fax: (408) 438 7023 Hybrid Products Farmingdale Tel: (516) 293 8686 Fax: (516) 293 0061 SOUTH EAST ASIA Singapore Tel: (65) 3827708 Fax: (65) 3828872 SWEDEN Stockholm Tel: 46 8 702 97 70 Fax: 46 8 640 47 36 UNITED KINGDOM & SCANDINAVIA Swindon Tel: (0793) 518510 Tx: 444410 Fax: (0793) 518582
These are supported by Agents and Distributors in major countries world-wide. © GEC Plessey Semiconductors 1993 Publication No. DS3883-1.2 September 1993
This publication is issued to provide information only which (unless agreed by the Company in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. The Company reserves the right to alter without prior knowledge the specification, design or price of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to the Company's conditions of sale, which are available on request.
3
|
|
