Details, datasheet, quote on part number: ZSM560G
PartZSM560G
Category
DescriptionReset Low Monitor
CompanyZetex Inc.
DatasheetDownload ZSM560G datasheet
Quote
Find where to buy
 
  

 

Features, Applications

The is a three terminal under voltage monitor circuit for use in microprocessor systems. The threshold voltage of the device has been set to 4.6 volts making it ideal for 5 volt circuits. Included in the device is a precise voltage reference and a comparator with built in hysteresis to prevent erratic operation. The ZSM560 features an open collector output capable of sinking at least l0mA which only requires a single external resistor to interface to following circuits. Operation of the device is guaranteed from one volt upwards, from this level to the device threshold voltage the output is held low providing a power on reset function. Should the supply voltage, once established, at any time drop below the threshold level then the output again will pull low. The device is available a TO92 package for through hole applications as well as SOT223 for surface mount requirements.

FEATURES

SOT223 and TO92 packages Power on reset generator Automatic reset generation Low standby current Guaranteed operation from 1 volt Wide supply voltage range Internal clamp diode to discharge delay capacitor 4.6 volt threshold for 5 volt logic 20mV hysteresis prevents erratic operation

APPLICATIONS

Microprocessor systems Computers Computer peripherals Instrumentation Automotive Battery powered equipment

Input Supply Voltage Offstate Output Voltage Onstate Output Sink Current(Note 1) Clamp Diode Forward Current(Note 1) Operating Junction Temperature Operating Temperature Storage Temperature to 10V Internally limited to 150C Power Dissipation 2W(Note 2)

TEST CONDITIONS (Tamb=25C for typical values, to 85C for min/max values (Note3)) COMPARATOR

PARAMETER Threshold Voltage High state output (Vcc increasing) Threshold Voltage Low state output (Vcc decreasing) Hysteresis SYMBOL VIH VIL 4.5 0.01

Output sink saturation: (Vcc=1.0V, Isink=0.1mA) Onstate output sink current (Vcc , Output=4V) Offstate output leakage current (Vcc , Output=5V) Clamp diode forward voltage (If=10mA) Propagation delay (Vin Rl=10k, Tamb=25C) Isink Ioh Vf Td VOL V s

Operating input voltage range Quiescent input current (Vcc=5V) Vcc V A

Note: 1. Maximum package power dissipation must be observed. 2. Maximum power dissipation for the SOT223 package is calculated assuming that the device is mounted on a PCB measuring 2 inches square. 3. Low duty cycle pulse techniques are used during test to maintain junction temperatures as close to ambient as possible. 4-360



 

Related products with the same datasheet
ZSM560C
ZSM560N8
Some Part number from the same manufacture Zetex Inc.
ZSM560N8 Reset Low Monitor
ZSM561
ZSR1000 Voltage Regulator
ZSR285C 2.85 to 12 Volt Fixed Positive Local Voltage Regulator
ZSR300 Voltage Regulator
ZSR570
ZSR600 Voltage Regulator
ZSR700
ZSR800 Voltage Regulator
ZSR850
ZSR900 Voltage Regulator
ZSRSeries 2.85 to 12v Fixed Positive Local Voltage Regulator
ZTR250 Fixed 2.5 3-terminal Voltage References
ZTX1047A NPN Low Sat Transistor
ZTX1048A
ZTX1049A
ZTX1051A
ZTX1053A NPN Med Power Transistor
ZTX1055A NPN High Voltage Transistor
ZTX1056A
ZTX1147A PNP Low Sat Transistor
 
0-C     D-L     M-R     S-Z