|
Details, datasheet, quote on part number:QQ-65
| |
| Part: | QQ-65 |
| Category: | RF & Microwaves => Phase Shifters |
| Description: | Description = Phase Shifter, Digitally Controlled Analog ;; Freq. Range = 0.1-18 GHZ |
| Company: | MCE KDI Integrated Products |
| Datasheet: | Download QQ-65 datasheet File size : 100 kB |
| Request For quote: | Find where to buy QQ-65
|
| |
Datasheet text preview:
DIGITALLY CONTROLLED ANALOG
PHASE SHIFTERS
8, 10, OR 12 BITS GENERAL INFORMATION
KDI/Triangle Corp. digitally controlled phase shifters vary the phase of a microwave signal in response to a TTL compatible logic input signal. The unit consists of an analog phase shifter, Series PQ, plus a digital to analog converter. (See Figure 1) A balanced stripline configuration keeps the VSWR and amplitude change to a minimum for all values of phase.
RF ITT CANNON DA-15P OR EQUIV. PIN PIN 1 9 0.25[6,4] E
SERIES QQ
0.125[3,18] DIA. THRU 3 MTG. HOLES
POWER/LOGIC
D
F
NOTE: EITHER B RF CONNECTOR MAY BE USED FOR INPUT
Standard units operate with 8 bits allowing 256 discrete values of phase. If 10 bits are required add 10 to Model No. (e.g., QQ-12-10). If 12 bits are required add 12 to Model No. (e.g., QQ-12-12).
ANALOG PHASE SHIFTER
C 0.10[2,5] 0.19 [4,826] 1.00 [25,4] SMA FEMALE TYP. A 0.38[2.65] TYP.
RF
RF
ELECTRICAL PERFORMANCE
+15 15
D/A CONVERTER
Figure 1
FIG. 1
GENERAL SPECIFICATIONS
Frequency Coverage: RF Impedance: RF Power: 0.1 to 18.0 GHz 50 OHMS. 10 mW peak or CW, operating. Destruct level is 1 W, CW, 100 W peak.
Temperature Information: The units can be used over a 55°C to +85°C temperature range. However, the phase will change either ±5° or ±5%, whichever is greater. If temperature compensation is required, this can be done on request. With compensation, the variation can be held to ±1° or ±1%, whichever is greater, from 55°C to +85°C. Compensation increases the cost by 10%. The size remains the same. If compensation is desired, add a suffix T to the model number, e.g. (QQ-17T). Connectors: SMA. Mating multipin connector is supplied with each unit; ITT Cannon DA-15S or equiv.
Model No. QQ-12 QQ-16 QQ-17 QQ-27 QQ-28 QQ-34 QQ-44 QQ-45 QQ-49 QQ-60 QQ-65 QQ-66 QQ-72 QQ-73 QQ-74 QQ-94
Frequency Range GHz 0.10.2 0.250.5 0.250.5 0.51.0 0.51.0 1.02.0 2.04.0 2.04.0 2.22.3 4.08.0 6.018.0 7.012.4 8.012.4 8.010.0 8.018.0 16.017.0
Phase Shift Note 4 Minimum Degrees 45 45 360 180 360 360 180 360 180 360 180 360 60 180 360 45
Insertion Loss Maximum dB 0.6 0.6 4.5 3.0 4.5 4.5 3.0 5.0 2.0 8.0 12.0 12.0 2.0 4.5 17.0 2.0
Amplitude Ripple Maximum ±dB 0.15 0.15 1.25 0.40 1.25 1.50 0.50 1.50 0.30 1.50 2.0 2.0 0.25 1.0 3.5 0.20
VSWR OutMaximum line 1.35 4 1.35 4 1.70 2 1.50 1 1.75 5 1.80 5 1.60 6 1.90 3 1.50 6 1.90 1 2.50 4 2.20 1 1.75 4 1.75 4 2.50 1 1.65 4
Notes:
1. The voltages required are 15 volts at 50 mA. 2. Switching speed of all models is 200 nanosec. Higher speeds on request. For 12 bits speed is 2 microsec. 3. Monotonicity is guaranteed for all models. 4. Phase Flatness: The phase shift varies with frequency at any voltage setting. This variation, referred to 0° at logic 0 for each frequency, is approximately 15% for octave models, 10% for models with 25% bandwidth, and 7.5% for models with a 10% bandwidth. 5. In order to determine the step size (least significant bit) of any phase shifter, divide the listed value of phase shift by the number of steps. POWER LOGIC PIN CONNECTIONS # Bits # Steps
MECHANICAL OUTLINES
Outline 1 2 3 4 5 6 A in [mm] 5.00 [127,0] 7.75 [196,9] 6.50 [165,1] 3.00 [76,2] 7.75 [196,9] 5.00 [127,0] B in [mm] 2.00 [50,8] 2.50 [63,5] 2.00 [50,8] 2.00 [50,8] 2.50 [63,5] 2.00 [50,8] C in [mm] N/A 4 holes N/A 4 holes N/A 4 holes 1.50 [38,1] N/A 4 holes N/A 4 holes D in [mm] 1.800 [45,7] 2.300 [58,42] 1.800 [45,7] 1.800 [45,7] 2.300 [58,42] 1.800 [45,7] E in [mm] 4.500 [114,3] 7.250 [184,15] 6.000 [152,4] 2.500 [63,5] 7.250 [184,15] 4.500 [114,3] F in [mm] 0.50 [12,7] 0.75 [19,1] 0.25 [6,4] 0.30 [7,6] 0.25 [6,4] 0.25 [6,4]
8 10 12
256 1024 4096
PIN* 112 13 14 15
FUNCTION Logic Inputs +15 VDC 15 VDC GND
*PIN 1 is least significant bit
KEY: Inches[Millimeters] .XX ±.03 .XXX ±.010 [.X ±0.8 .XX ±0.25]
60 South Jefferson Road, Whippany, NJ 07981 Tel: 973-887-8100 · Fax: 973-884-0445 email: sales@mcekdi-integrated.com See us on the web @ www.mcekdi-integrated.com
11-5-02
|
|
