|
|
Part: PX1002
Category:
Timing Circuits
-> Resonators
-> SAW Resonators
Description: Frequency = 86.85 ;; Description = Filter, IS-54 Tdma if
Company: RF Monolithics
Datasheet: Download PX1002 datasheet File size : 24 kB
Request For quote: Find where to buy PX1002
Datasheet text preview:
®
PX1002 86.85 MHz SAW Filter
Value +10 30 -40 to +85 265°C for 10 s Units dBm VDC °C
· · · · ·
Designed for TDMA IS-54 Receiver IF Applications Low Insertion Loss Excellent Selectivity Hermetic 13.3 X 6.5 mm Surface-Mount Case Unbalanced Input and Output
Absolute Maximum Ratings
Rating Maximum Incident Power in Passband Max. DC voltage between any 2 terminals Storage Temperature Range Max Soldering Profile
SM13365-12
Electrical Characteristics
Characteristic Nominal Center Frequency Passband Insertion Loss at fc 3 dB Passband Amplitude Ripple over fc ±15 kHz Group Delay Variation over fc ±10 kHz Third-Order Intermod. for -20 dBm tones at fc ±60 & 120 kHz Rejection fc ±60 kHz fc -880 kHz to fc -940 kHz Ultimate Operating Temperature Range Impedance Matching to 50 unbalanced Case Style Lid Symbolization (YY=year, WW=week) See note 4 TA 1 -20 External L-C SM13365-12 13.3 X 6.5 mm Nominal Footprint RFM PX1002 YYWW 1, 2, 3 11 65 65 +70 °C 16 dB GDV Sym fC IL BW3 1, 2 Notes 1 ±12 Min Typ 86.850 3 ±25 1.0 6.0 -95 Max 4.0 Units MHz dB kHz dBP-P µ s P-P dBm
Electrical Connections
Connection Port 1Hot Port 1 Gnd Return Port 2 Hot Port 2 Gnd Return Case Ground Terminals 2 3 8 9 All Others
Notes:
1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 and measured with 50 network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." The design, manufacturing process, and specifications of this filter are subject to change. 6. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. US and international patents may apply. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc. ©Copyright 1999, RF Monolithics Inc. Electrostatic Sensitive Device. Observe precautions for handling.
2. 3.
7. 8. 9. 10.
4. 5.
RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.
E-mail: info@rfm.com http://www.rfm.com PX1002 051403
PX1002 86.85 MHz SAW Filter
0 dB -20
-40
-60
-80 300 kHz/DIV
0 dB -4
µs
24 21 18 15
-8
12 9
-12
6 3
-16 30 kHz/DIV
0
RF Monolithics, Inc.
4347 Sigma Road Dallas, Texas 75244 USA
Phone: +1(972)233-2903 Fax: +1(972)387-8148 e-mail: info@rfm.com Home page: www.rfm.com
European Sales Office
PX1002 051403
86.85 MHz
Tape and Reel Specifications
SAW Filter
100 REF.
"B" REF.
Quantity Per Reel
254
100 Min 1000 Max
See Detail "A" 12..0 24 4
0 13.
21.0
.2
20
2.0
COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions Ao Bo Ko Pitch W 7.0 mm 13.8 mm 2.0 mm 12.0 mm 24.0 mm
PIN #1 USER DIRECTION OF FEED
RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.
E-mail: info@rfm.com http://www.rfm.com PX1002 051403
Others parts begin by px
PX-1 PX-2
|
|
|
