|
|
Part: SL339N
Category:
Analog & Mixed-Signal Processing
-> Comparators
Description: Quad Single Supply Comparator
Company: System Logic Semiconductor
Datasheet: Download SL339N datasheet File size : 42 kB
Request For quote: Find where to buy SL339N
Datasheet text preview:
SL339
Quad Single Supply Comparator
The SL339 consists of four independent precision voltage comparators with an offset voltage specification as low as 2.0 mV max for four comparators which were designed specifically to operate from a single power supply over a wide range of voltages. Application areas include limit comparators, simple analog to digital converters; pulse, squarewave and time delay generators; wide range VCO; MOS clock timers; multivibrators and high voltage digital logic gates. · Single or Split Supply Operation · Low Input Bias Current · Low Input Offset Current · Input Common Mode Voltage Range to Gnd · Low Output Saturation Voltage · TTL and CMOS Compatible
ORDERING INFORMATION SL339N Plastic SL339D SOIC TA = 0° to 70° C for all packages.
LOGIC DIAGRAM PIN ASSIGNMENT
PIN 3 = VCC PIN 12 = GND
SLS
System Logic Semiconductor
SL339
MAXIMUM RATINGS *
Symbol VCC Power Supply Voltages Single Supply Split Supplies VI D R VICR ISC IIN TJ Tstg TL PD Input Differential Voltage Range Input Common Mode Voltage Range (1) Output Short Circuit to Ground Input Current, per pin (2) Junction Temperature Plastic Packages Storage Temperature Lead Temperature, 1mm from Case for 10 Seconds Power Dissipation @TA=25°C Plastic Package Derate above 25°C 150 -65 to +150 260 1.0 8.0 °C °C °C W mW/°C 36 ±18 36 -0.3 to VCC Continuous 50 mA V V V Parameter Value Unit
*
Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. Notes: 1. Split Power Supplies. 2. VIN<-0.3V. This input current will only exist when voltage at any of the input leads is driven negative.
RECOMMENDED OPERATING CONDITIONS
Symbol VCC TA DC Supply Voltage Operating Temperature, All Package Types Parameter Min ±2.5 or 5.0 0 Max ±15 or 30 +70 Unit V °C
This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, VIN and VOUT should be constrained to the range GND(VIN or VOUT)VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or V C). C Unused outputs must be left open.
SLS
System Logic Semiconductor
SL339
DC ELECTRICAL CHARACTERISTICS(TA=0 to +70°C)
Guaranteed Limit Symbol VIO Parameter Input Offset Voltage Test Conditions V0=1.4V VCC=5.0-30V;RS100 VICR=0V - (VCC-1.5)V V0=1.4V VCC=5.0-30V VICR=0V - (VCC-1.5)V V0=1.4V VCC=5.0-30V VICR=0V - (VCC-1.5)V VCC=5.0-30V RL=,VCC=5.0 RL=,VCC=30V A VOL t1 Voltage Gain Large Signal Response Time Response Time Output Sink Current Saturation Voltage Output Leakage Current VCC=15V, RL=15K VIN=TTL Logic Swing, Vref=1.4V, VCC=5.0V, RL=5.1K , VRL=5.0V VCC=5.0V, RL=5.1K , VRL=5.0V VI(-)=1.0V, VI(+)=0V, V01.5V, VCC=5.0V VI(-)=1.0V, VI(+)=0V, Isink4.0mA, VCC=5.0V VI(+)=1.0V, VI(-)=0V, V0=5.0V V0=30V Min Typ Max 9.0 Unit mV
II B
Input Bias Current
-
400
nA
IIO
Input Offset Current
-
±150
nA
VICR ICC
Input Common Mode Voltage Range Supply Current
0 200* 300*
VCC-2.0V 2.0* 2.5* -
V mA V/mV ns
t2 Isink Vsat IOL
6.0* -
1.3* -
700
µs mA mV nA
0.1* 1000
VI D R *=@25°C
Differential Input Voltage Range
All VINGND or V-Supply (if used)
VCC*
V
SLS
System Logic Semiconductor
Others parts begin by sl
SL-1 SL-2 SL-3 SL-4 SL-5 SL-6 SL-7 SL-8 SL-9 SL-10 SL-11 SL-12 SL-13
|
|
|
