Details, datasheet, quote on part number: GW70703
DescriptionSerial Annunciator Driver Module, main Driver with 16-outputs
CompanyGamewell FCI
DatasheetDownload GW70703 datasheet


Features, Applications

The 600 Series serial annunciator driver (SAN) is used to light a lamp or LED in an annunciator. It also provides a switched positive output per point for interface with building automation systems or driving relays. Each device is capable of interpreting the instructions from the main CPU, initiating its own programmed response, and retransmitting the instructions to the next device. The Gamewell-FCI 600 systems can accommodate to 64 devices connected to the serial communications port. In addition to the serial annunciator drives (SAN), these devices include remote annunciator (RAN) and remote printer interface (RPI). This combination of devices comprise the Gamewell-FCI status control network. Since each device contains its own microprocessor, each can be programmed independently. A series of devices can be programmed directly over the network from a single device, saving valuable installation time. Programming is accomplished via Windows®-based configuration software. Each SAN input point can activate up to five output points for matrix annunciation. There are two basic models available, the SAN and the SAN-RC. The SAN-16 is equipped with 16 freely programmable outputs which can be used for remote control or monitoring, expandable to 128 points using PDM modules. The SAN-16-RC has all of the features of the SAN-16, plus the ability to read inputs into the system. The SAN-16-RC has provisions for four inputs for: remote acknowledge, reset, signal silence, and lamp test. In addition to the basic 16 outputs, there are eight (8) common outputs for: common system alarm, common system trouble, AC power, communications, action required LED prompts for system acknowledge, reset and signal silence, and a driver for a local audible. The status control network, including SAN units, is connected to the main 600 Series control panel via an RS-232 data communication line. The SIM-232 module is used to

Microsoft® Windows® is a registered trademark of Microsoft® Corporation. gwf2027ph1.wmf

to 64 devices supported on a single 600 Series control panel. Windows®-based field programming. Dual optically isolated serial ports. Can interface with building automation systems via standard ASCII communication. Microprocessor based. Expandable in 16 point increments to 128 points. Supervised. Allows remote system control. Mounting track included.

Specifications are for information only, are not intended for installation purposes, and are subject to change without notice. No responsibility is assumed by Gamewell-FCI for their use. ©2007 Honeywell International Inc. All rights reserved. CS-2027 Rev. A page of 2

12 Clintonville Road, Northford, CT 06472-1610 USA Tel: (203) 484-7161 Fax: (203) 484-7118

provide an isolated RS-232 output from the main CPU of the 600 Series system panels. The IF602 and IF610 panels have built-in RS-232 ports.


The SAN units provide a means for remote annunciation and control of the system via a simple RS-232 connection. These driver units fit neatly into an annunciator unit and can be used to drive the LED or incandescent lights of a standard or graphic-type annunciator. When it is necessary for remote system control, the SAN-16-RC provides for up to eight inputs for system control. Any or all inputs may be used to customize any given command station's capabilities. The SAN units can also be used to interface with other building systems via ASCII or where dry contacts or a switched output is required. The SAN's outputs can be used to drive a relay to interface or control virtually any remote point or group of points.

Remote annunciation and control for the main control panel shall be supplied where indicated. Remote annunciation and control shall be accomplished via the RS-232 data communications line. It shall be possible to add to 64 devices to the communication line. Each device shall be capable of driving to 128 points. It shall be possible to mix annunciators, printers and LCD alphanumeric displays on a single line without the need for special software. Devices shall not be placement sensitive. All devices shall be individually field programmable and independent from each other. The device shall be Gamewell-FCI part numbers.

Serial annunciator driver module, main driver with 16-outputs. SAN-# Serial annunciator driver module, specify number of outputs in 16-point increments (i.e., SAN-48, SAN-128). Includes mounting track and interconnect cables. Contact the Gamewell-FCI Technical Support for details. SAN-16-RC Serial annunciator driver with four-remote control inputs, eight (8) common outputs and 16-outputs. SAN-#-RC Serial annunciator driver with four- remote control inputs, eight (8) common outputs and a specifiable number of outputs in 16-point increments (i.e., SAN-48-RC, SAN-128-RC). Includes mounting track and interconnect cables. Contact Gamewell-FCI Technical Support for details. PDM-16 Point driver module for field-expanding serial annunciator drivers, 16 outputs. SIM-232 Required serial interface module, mounts in 600 Series control 632, 654, and 658 to supply RS-232 ouputs. Note: This model is not required for use with the IF602 and IF610 Systems. GW70703 Programming cable (Programmed via a Windows®-based SAN program). Found on the Gamewell-FCI website. Note: This program is only available to Gamewell-FCI authorized distributors.


Serial Annunciator Driver: Basic SAN and SAN-RC provide 16point drives. SAN Input Power: 24 VAC/VDC Standby Current: 0.04 A max. Alarm Current: 2.0 A max. Output Power: 0.040 A max. per output. Dimensions: 5.1 D cm)

Input Power: From SAN Module Standby Current: 0.002 A Alarm Current: 0.002 A

12 Clintonville Road, Northford, CT 06472-1610 USA Tel: (203) 484-7161 Fax: (203) 484-7118 CS-2027 Rev. A page of 2


Some Part number from the same manufacture Gamewell FCI
FC-RM Zoned Audio Command Center Voice Evacuation Control Panel
MX-TCR Fire Phone Accessories
MS95-SD Addressable Manual Pull Station with Smartscan
BEAMMMK Intelligent beam Smoke Detector
7628 Four-zone Panel
30431 Fire Fighter Phone Accessories
TR-3B Multiprocessor-based
SNAC-9 Supplementary Notification Appliance Circuit Panel
SCE-95 Signal Control Element
AS-241575W-FR Wheelock AS Series Audible Strobe Devices & AH Series Audible Devices
SS-PDR Intelligent Low-flow Photoelectric Duct Smoke Detectors
XRM-24 Fire Alarm Control Panel with Built-in DACT and Remote-site Upload/download Capability
SS-BF Filtrex Hostile Area Smoke Head Analog Addressable Detector with Smartscan
71742 Series ET LOW Profile Speaker Strobes
FST-8 Duct Housing, 4-wire, less Detector head
AS9025 Cooper-wheelock As/ah Serles
VSYS1 Emergency Voice Evacuation
IF602VE-126 Analog Addressable Control Panel with Voice Evacuation
301BL4 Photoelectronic Detector
SCD Signal Control Element
F402 Two-zone Fire Alarm Control Panel

CH90-24-W : Wheelock CH Series Electronic Chimes & Chime Strobes

NS-121575W : Cooper-wheelock NS Series Horn Strobes & NH Series Horns

DH-SB1 : Electromagnetic Door Holders

PC24177W : SC Strobes and PC Horn/strobes

P1224MCW : Selectable Output Strobes AND Horns

M34-114 : Three-fold Fire Alarm Boxes and Transmitters

CAB-D : Multiprocessor-based

VSYS14 : Emergency Voice Evacuation

A5060 : Intelligent Low-flow Photoelectric Duct Smoke Detectors

Same catergory

FU-319SPA-C6 : Ingaas Apd Preamp Module For The 1.31 & 1.55 Wavelength Range. FU-319SPP-C6 is InGaAs avalanche photodiode module with GaAs preamplifier, designed for use in high-speed, long haul optical communication systems. The coaxial package contains InGaAs avalanche photodiode coupled with single-mode fiber pigtail and GaAs preamplifier. High-sensitivity (-33dBm typ) 5pin coaxial package Selectable single power supply voltage.

SSL-LXA1008SUGTR41 : Z-bend Axial Leads / Flat Lens - Alingap/gaalas.

ADL5320 : 400 MHz to 2700 MHz Pre-driver RF Amplifier The ADL5320 is a broadband, linear pre-driver RF amplifier that operates at frequencies from 400 MHz to 2700 MHz. The device can be used in a wide variety of wired and wireless applications, including ISM, WLL, PCS, GSM, CDMA and WCDMA. The ADL5320 operates with 5 V supply voltage with a supply current of 104 mA. The ADL5320.

CITR208Q1G : Circuit Breaker WITH On/off Capability. This unique circuit breaker consists of a thermal circuit breaker and a rocker switch style housing. When an overload condition occurs, the contacts will break apart. By returning the actuator to the OFF position, then back to ON, the circuit breaker mechanism with reset. S Electrical Ratings Electrical Life Contact Resistance Dielectric Strength Insulation.

X25642M : Advanced SPI Serial E2prom with Block Lock Protection. This X25642 device has been acquired by IC MICROSYSTEMS from Xicor, Inc. Advanced SPI Serial E PROM with Block Lock 2MHz Clock RateLow Power CMOS --<1µA Standby Current --<5mA Active To 5.5V Power SupplySPI Modes X 8 Bits --32 Byte Page ModeBlock Lock Protection 2 --Protect 1/2 or all of E PROM ArrayBuilt-in Inadvertent Write Protection --Power-Up/Down.

OM5204SC : Hermetic Jedec To-258aa HIGH Efficiency, Center-tap Rectifier. HERMETIC JEDEC TO-258AA HIGH EFFICIENCY, CENTER-TAP RECTIFIER Very Low Forward Voltage Very Fast Switching Time Hermetic Metal Package, JEDEC TO-258AA Low Thermal Resistance Isolated Package High Surge Available Screened To MIL-S-19500, TX, TXV And S Levels This series of products in a hermetic package is specifically designed for use at power switching.

531-40047-4 : RF Connectors RA PCB F JACK NO HDW. s: Manufacturer: Amphenol ; Product Category: RF Connectors ; RoHS:  Details ; Product: Connectors ; RF Series: F ; Gender: Receptacle (Female) ; Contact Plating: Tin ; Shell Plating: Tin ; Impedance: 75 Ohms ; Body Style: Right Angle ; Connector Type: Connectors - Printed Circuit Board ; Packaging: Bulk ; Factory.

MCP4361-103E/ST : IC, DIGITAL POT 10KOHM 257 QUAD 20-TSSOP. s: End To End Resistance: 10kohm ; Track Taper: - ; Resistance Tolerance: - ; No. of Steps: 257 ; Supply Voltage Range: 2.7V to 5.5V ; Control Interface: Serial, SPI ; No. of Pots: Quad ; Memory Type: EPROM - OTP ; Temperature Coefficient: ± 150ppm/°C ; Potentiometer IC Case Style: TSSOP ; No. of Pins: 20 ; Operating.

255-328SR16M-ROX : Speakers & Transducers 32.8khZ RECEIVER. Higher sensitivity, wider bandwidth, and excellent stability over a wide temperature and humidity range. s: Manufacturer: Kobitone ; Product Category: Speakers & Transducers ; RoHS:  Details ; Frequency Range: 32.8 KHz ; Sound Pressure Level: - 67 dB ; Maximum Power Rating: 0.2 W ; Shape: Round ; Termination.

MAX16029TG+ : Supervisory Circuits Dual/Triple/Quad Sequencng/Suprvisory. s: Manufacturer: Maxim Integrated Products ; RoHS:  Details ; Number of Voltages Monitored: 4 ; Output Type: Open Collector / Drain ; Manual Reset: Resettable ; Watchdog: No Watchdog ; Power-Up Reset Delay (Typ): 190 ms ; Supply Voltage (Max): 28 V ; Supply Voltage (Min): 2.2 V ; Supply.

D38999/26FB35JN : Aluminum, Nickel Plated, Electroless Free Hanging (In-Line) Circular Connectors, Interconnect Plug, Female Sockets; CONN PLUG 13POS STRAIGHT W/SCKT. s: Connector Type: Plug, Female Sockets ; Shell Size - Insert: 11-35 ; Mounting Type: Free Hanging (In-Line) ; Fastening Type: Threaded ; : Shielded ; Packaging: Bulk ; Number of Positions: 13 ; Termination:.

BA9743AFV-E2 : Pmic - Voltage Regulator - Dc Dc Switching Controller Integrated Circuit (ics) Controller Digi-Reel® 3.6 V ~ 35 V; IC CTRLR REG 2CH SW SSOP-B16. s: PWM Type: Controller ; Number of Outputs: 2 ; Package / Case: 16-TSSOP (0.173", 4.40mm Width) ; Packaging: Digi-Reel® ; Duty Cycle: 100% ; Voltage - Supply: 3.6 V ~ 35 V ; Frequency - Max: 800kHz ; Buck:.

OSTHA172150 : Through Hole Terminal Block - Wire To Board Connectors, Interconnect Through Hole; CONN TERM BLOCK 17POS 7.62MM. s: Color: Green ; Current: 10A ; : Lever Actuated ; Mating Orientation: Horizontal with Board ; Mounting Type: Through Hole ; Pitch: 0.300" (7.62mm) ; Voltage: 300V ; Wire Gauge: 14-24 AWG ; Number of Levels: 1 ; Positions Per Level: 17 ; Packaging:.

TAS5508-5142K7EVM : Eval Board - Audio Amplifier Programmers, Development System; EVAL MODULE FOR TAS5508B/TAS5142. s: Amplifier Type: Class D ; Board Type: Fully Populated ; Max Output Power x Channels @ Load: 100W x 2 @ 4 Ohm ; Output Type: 2-Channel (Stereo) ; Operating Temperature: 0°C ~ 70°C ; Voltage - Supply: 10.8 V ~ 13.2 V ; Utilized IC / Part: TAS5142, TAS5508B.

PV36Z253A01B00 : Ohm Trimmer Potentiometers, Variable Resistors Side Adjustment 25 Turn; TRIMMER 25K OHM 0.5W TH. s: Resistance (Ohms): 25K ; Power (Watts): 0.5W, 1/2W ; Number of Turns: 25 ; Adjustment Type: Side Adjustment ; Tolerance: ±10% ; Mounting Type: Through Hole ; Temperature Coefficient: ±100ppm/°C ; Resistive Material: Cermet ; Packaging: Bulk ; Lead Free.

ETQP6F2R0HL : 1 ELEMENT, 3.5 uH, GENERAL PURPOSE INDUCTOR, SMD. s: Mounting Option: Surface Mount Technology ; Devices in Package: 1 ; Lead Style: J ; Standards and Certifications: RoHS ; Application: General Purpose, Power Choke ; Inductance Range: 3.5 microH ; Inductance Tolerance: 30 (+/- %) ; DCR: 0.0033 ohms ; Rated DC Current: 12500 milliamps ; Testing.

RM21TR-15P(71) : 15 CONTACT(S), ZINC ALLOY AND BRASS, MALE, CIRCULAR CONNECTOR, SOLDER, RECEPTACLE. s: Gender: Male ; Termination Types: SOLDER ; Mounting Style: CableEnd, 4-hole ; Number of Contacts: 15 ; Approvals: RoHS.

34-02UYC/S599 : T-1 3/4 SINGLE COLOR LED, SUPER YELLOW, 5 mm. s: LED Type: Yellow ; Peak Wavelength: 591 nm (5910 Ă…) ; Viewing Angle: 40 degrees ; Forward Current: 150 milliamps ; LED Package : T-1 3/4.

0-C     D-L     M-R     S-Z