Details, datasheet, quote on part number: TDA7375H
PartTDA7375H
Category
Description
CompanyN.A.
DatasheetDownload TDA7375H datasheet
Quote
Find where to buy
 
  

 

Features, Applications

HIGH OUTPUT POWER CAPABILITY: x 35W/4 EIAJ x 35W/4 EIAJ 1KHz, 10% MINIMUM EXTERNAL COMPONENTS COUNT: NO BOOTSTRAP CAPACITORS NO BOUCHEROT CELLS INTERNALLY FIXED GAIN (26dB BTL) ST-BY FUNCTION (CMOS COMPATIBLE) NOAUDIBLE POPDURING ST-BYOPERATIONS DIAGNOSTICS FACILITY FOR: CLIPPING OUT TO GND SHORT OUT TO VS SHORT SOFT SHORT AT TURN-ON THERMAL SHUTDOWN PROXIMITY Protections: OUPUT AC/DC SHORT CIRCUIT BLOCK DIAGRAM

TO GND VS ACROSS THE LOAD SOFT SHORT AT TURN-ON OVERRATING CHIP TEMPERATURE WITH SOFT THERMAL LIMITER LOAD DUMP VOLTAGE SURGE VERY INDUCTIVE LOADS FORTUITOUS OPEN GND REVERSED BATTERY ESD

DESCRIPTION The is a new technology class AB car radio amplifier able to work either in DUAL BRIDGE or QUAD SINGLE ENDED configuration. The exclusive fully complementary structure of the output stage and the internally fixed gain guaranABSOLUTE MAXIMUM RATINGS

Symbol Vop VS Vpeak IO Ptot Tstg, Tj Operating Supply Voltage DC Supply Voltage Peak Supply Voltage (for = 50ms) Output Peak Current (not repetitive = 100s) Output Peak Current (repetitive > 10Hz) Power Dissipation (Tcase = 85C) Storage and Junction Temperature Parameter Value to 150 Unit C

tees the highest possible power performances with extremely reduced component count. The on-board clip detector simplifies gain compression operation. The fault diagnostics makes it possible to detect mistakes during car radio set assembly and wiring in the car. GENERAL STRUCTURE

Symbol Rth j-case Description Thermal Resistance Junction-case Max Value 1.8 Unit C/W

ELECTRICAL CHARACTERISTICS (Refer to the test circuit, 1KHz; T amb = 25C, unless otherwise specified

Symbol VS Id VOS PO Parameter Supply Voltage Range Total Quiescent Drain Current Output Offset Voltage Output Power THD = 4 Bridge Single Ended Single Ended, = 14.4V, Bridge = 13.7V, Bridge Single Ended, to 4W Bridge, = 1KHz Single Ended = 10KHz Single Ended = 1KHz Bridge = 10KHz Bridge IN GV EIN Input Impedance Voltage Gain Voltage Gain Match Input Noise Voltage = 0; "A" weighted, S.E. Non Inverting Channels Inverting Channels Bridge to 22KHz SVR A SB ISB SB Ipin7 Supply Voltage Rejection Stand-by Attenuation ST-BY Current Consumption ST-BY In Threshold Voltage ST-BY Out Threshold Voltage ST-BY Pin Current Play Mode = 5V Max Driving Current Under Fault Icd off Icd on Vsat pin10 Clipping Detector Output Average Current Clipping Detector Output Average Current Voltage Saturation on pin = 5% Sink Current at Pin = 1W VST-BY to 1.5V Single Ended Bridge Single Ended Bridge RL = Test Condition Min. 8 Typ. Max. 18 150 Unit A V

Max. Output Power EIAJ Output Power Distortion

See built-in S/C protection description Pin 10 Pulled-up to 5V with = 4 Saturated square wave output.


 

Some Part number from the same manufacture
TDA7427AAD1
TDA7430.31
TDA7437T
TDA7460
TDA8005AG
TDA8011
TDA8040
TDA8041
TDA8042
TDA8043K
TDA8060
TDA8114
TDA8134
TDA8147
TDA8174A-AW
TDA8198
TDA8204
TDA8214
TDA8215
TDA8304
TDA8315
 
0-C     D-L     M-R     S-Z